Question about Hyundai Motor 2004 Sonata

1 Answer

Timing marks of cam shaft timing belt - Hyundai Motor 2004 Sonata

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Timing marks on a 2001 2.5 sonata

Posted on Mar 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replace timing belt but cant set timing


Hi Robert, It would help to know what engine is in your vehicle? A rule of thumb way to set up the valve timing is as follows. Rotate the crank shaft until the crank shaft mark is about 90 degrees from TDC. This will protect the valves from damage when rotating the cams to align them. With the tappet cover removed rotate the cam shaft or shafts so that the number one cylinder is on compression (both inlet and exhaust valves fully closed) and the last cylinder in line on overlap, Look for adjacent timing marks on the cam gears and somewhere close to those look for the alignment marks (maybe notch marks, holes or indented match marks). (Some manufactures use the machined gasket surface where the tappet cover closes onto the cylinder head). Look closely for the static mark on the cylinder head and align the cam(s) to it or them. Once completed, set the crank at Top Dead Center and look carefully for a timing mark which aligns with the gear and set them. Fit the belt so the marks align when the tensioner bearing is released and presses the belt under load. (follow the manufactures recommended tightening instructions.) . (Remember never to crimp a timing belt, if it has been, throw it away and get another, even if it is new!) If the belt snapped and that is the reason for replacement, internal damage may have resulted inside the engine. A snapped belt may cause damage to the valves, the camshafts, the cam shaft caps and to the pistons. If the engine turns much faster than expected and sounds as if there is no compression, you have problems! (Those I've just mentioned. I hope not for your sake. best of luck Regards John

Dec 12, 2011 | 2000 Hyundai Accent

3 Answers

How to set timing when you relesh tensioner and it changes the alignment postion of pullies 2000 ford ranger 2.5 l


Here is the trick. Align marks. Put the timing belt on the crank shaft pulley first, and after on the overhead cam pulley. Release tensioner and rotate the crank shaft till the timing belt makes two full circles. Try to align marks, you will be at least one tooth off. Align the crank shaft on the mark, and find out how many teeth you are off at the cam shaft pulley. Count the teeth. Remove the timing belt from cam shaft pulley only. Move cam shaft pulley in reverse according to the number of teeth you counted. Make sure the crank shaft pulley is on the mark. Mount the belt at cam shaft pulley.Rotate the belt two circles and check the marks. Repeate this procedure til after releasing the tensioner, and rotating the timing belt two full circles, the mars will be align.

Nov 22, 2010 | 2000 Ford Ranger SuperCab

1 Answer

How do i time my Golf 1 correctly? it consumes a lot


its tricky enough if your not sure what your doing but ill run you through it. 1. remove top rocker cover and timing belt cover. 2 make up the position of the pully on the cam shaft at the top and the drive shaft at the bottom, this marks are you fail safe incase you cant time the engine. 3 remove the timing belt and pully tentioner, note if your going this far you are as well to replace the timing belt,tentioner and water pump. 4 On the cam shaft at the top if you force them to turn you will see a small indicator mark on the shaft this mark has to line up with the other indicator mark on the housing between the cam shaft and the cam shaft pully, once they line up your top end is timed, mark up the pully incase it moves. 5 on the drive shaft pully there is also markings that have to line up but you can also feel the position of the pully as you turn it, you will feel the piston been forced up and it is timed at top dead centre on cylinder one, which means the the piston has to be at the top just before the point of returning back down, using your feeling as a guide and the markings lined up you will have timing. also mark up this pully, your new marking should be very very close to the fail safe markings you put on at the start. when you have your marking replace the timing belt with the longest distance between pully contact going on first, try not disturb your timing or your hard work will have been for nothing, make sure the tentioner on the belt is tight but not to tight to the point where you ll stretch the belt or snap it, put everything back as you found it and crank the engine, job done, best of luck. hope this helps( rate me on my answer thanks )

Aug 27, 2010 | 2000 Volkswagen Golf

2 Answers

Timming bailt marks for 1990 plym laser rs


REMOVAL & INSTALLATION 1.8L Engine
  1. If possible, position the engine so the No. 1 piston is at TDC.
  2. Disconnect the negative battery cable.
  3. Remove the timing belt covers.
  4. Remove the timing (outer) belt tensioner and remove the outer timing belt.
  5. Remove the outer crankshaft sprocket and flange.
  6. Remove the silent shaft (inner) belt tensioner and remove the belt. Fig. 1: Silent shaft belt timing marks — 1.8L engine 89573g93.gif
    Fig. 2: Checking the silent shafts for proper positioning 89573g94.gif
    Fig. 3: Timing belt timing mark alignment — 1.8L engine 89573g95.gif
    To install:
  7. Align the timing marks of the silent shaft sprockets and the crankshaft sprocket with the timing marks on the front case. Wrap the timing belt around the sprockets so there is no slack in the upper span of the belt and the timing marks are still aligned.
  8. Install the tensioner pulley and move the pulley by hand so the long side of the belt deflects about 1⁄4 in.
  9. Hold the pulley tightly so the pulley cannot rotate when the bolt is tigthened. Tighten the bolt to 15 ft. lbs. (20 Nm) and recheck the deflection amount.
  10. Install the timing belt tensioner fully toward the water pump and tighten the bolts. Place the upper end of the spring against the water pump body.
  11. Align the timing marks of the camshaft, crankshaft and oil pump sprockets with their corresponding marks on the front case or rear cover. NOTE: There is a possibility to align all timing marks and have the oil pump sprocket and silent shaft out of time, causing an engine vibration during operation. If the following step is not followed exactly, there is a 50 percent chance that the silent shaft alignment will be 180 degrees off.
  12. Before installing the timing belt, ensure that the left side (rear) silent shaft (oil pump sprocket) is in the correct position as follows:
    1. Remove the plug from the rear side of the block and insert a tool with shaft diameter of 0.31 in. (8mm) into the hole.
    2. With the timing marks still aligned, the shaft of the tool must be able to go in at least 2 1/2 in. If the tool can only go in about 1 in., the shaft is not in the correct orientation and will cause a vibration during engine operation. Remove the tool from the hole and turn the oil pump sprocket 1 complete revolution. Realign the timing marks and insert the tool. The shaft of the tool must go in at least 2 1/3 in.
    3. Recheck and realign the timing mark.
    4. Leave the tool in place to hold the silent shaft while continuing.
  13. Install the belt to the crankshaft sprocket, oil pump sprocket, then camshaft sprocket, in that order. While doing so, make sure there is no slack between the sprocket except where the tensioner is installed.
  14. Recheck the timing marks' alignment. If all are aligned, loosen the tensioner mounting bolt and allow the tensioner to apply tension to the belt.
  15. Remove the tool that is holding the silent shaft and rotate the crankshaft a distance equal to 2 teeth on the camshaft sprocket. This will allow the tensioner to automatically apply the proper tension on the belt. Do not manually overtigthen the belt or it will howl.
  16. Tigthen the lower mounting bolt first, then the upper spacer bolt.
  17. To verify correct belt tension, check that the deflection at the longest span of the belt is about 1⁄2 in.
  18. Install the timing belt covers and all related items.
  19. Connect the negative battery cable.

Aug 02, 2010 | 1990 Plymouth Laser

1 Answer

Set harmonic balancer to top dead centre,set cams to timing marks,engine will not start but turns over. Hyundai Terracan 2002


hi from uk assume you have renewed c/belt and balance shaft timing belt? if so? and sure your timing marks on cams and the c/shaftcog are correct ? the oil pump also correctly aligned with marks? and the balance shaft gear also has time marking ? want to run thro how and which marks you have aligned and at TDC No1 all belt/s have to be aligned ??

Dec 27, 2009 | Hyundai Sonata Cars & Trucks

1 Answer

Need timing belt marks for 2003 sonata


timing belt marks are as follows= crank at TDC marks are at 10 oclock the both cams marks at TDC are at 12 .oclock position marks are clear if you look theoil pump gear also driven by belt marks are approx 11 oclock position also marked thebalance shaft gear/cog must also be set to 9 oclock position when the b/shaft belt is fitted to hold theoil pump sprocket in its correct position remove the small screw/blank plug on side of block then use an 8 mm posi screwdriver insert into hole it should travel approx 60 mm to engage if not rotate pump gear 360 degree till it does locate fit main belt from crank anti clockwise to cams then tension same with b/shaft tensioner make sure you torque all bolts correctly any more info req'd come back hope this helps ?

Dec 17, 2009 | Hyundai Motor 2003 Sonata

1 Answer

Timing engine


I had a 2.4 L engine in a caravan and replace the water pump that was controlled by the timing belt.
I was having the same problem, I called my bother in law to help. The crank shaft has to stay perfectly timing on the low end. The cam shaft marks are set exactly one half of a tooth apart. So when looking at it, The left side cam gear mark is a half a tooth higher then the right side. Then you have to try and slip on the belt . That is the easy part. When letting go of the timing belt tensioner the marks should line up perfectly across from each other. You have to take off the belt again and make sure you keep correct tension on the crank shaft so the mark is not moving when you are putting on the belt. There is a web site call Alldata.com. The web site cost a few dollars but it willl give you a detail instructions on how to time the engine with pictures to guide you. This is the same web site the pro's use.

I hope this has been helpful.

Oh, by the way you are lucky because the engine is not an interferrence type , so you can not damage the valves at least. Since you know the oil pump is out of time , check all the spark plugs again , they are probably oil soaked .

May 01, 2009 | Mitsubishi Diamante Cars & Trucks

1 Answer

Timimg for a 1990 nissan maxima


If your belt came with marks, then they should match the marks that are on the sprockets and block, if not, you must have the cam marks align with those on the engine. If you're in doubt about the exact spot, lay a tooth pick across the sprockets so that you can check alignment to the block.

Apr 12, 2009 | 1990 Nissan Maxima

2 Answers

1994 Volvo 940 Station Wagon timing belt


I hope you've solved the problem by now, but there are alignment marks on the crank shaft (top pulley), idler (lower side), and cam shaft (smaller, bottom pulley) which should be aligned with stationary marks on the timing belt rear cover.

The belt has marks that align with the aforementioned marks (lines). The double marks on the belt align with the camshaft marks and the single marks with the others.

Loosen the tensioner clamp (nut) to allow the spring loaded tensioner to press on the belt and retighten the nut.

Rotate the crank shaft (clockwise, probably two revolutions) and make sure the pulley marks realign to the marks on the cover (they don't have to realign with the marks on the belt).

Rotate the crank shaft a full revolution once the belt is on and check that alignment is preserved.

Periodically loosen and retension the tensioner nut (access through a hole in the cover) to ensure that tension is maintained as the belt relaxes.

Oct 25, 2008 | 1994 Volvo 940

2 Answers

Timing belt on 2004santa fe crdi


It's a lot of work, and should be done at 60,000 miles. You will have to remove the front cover of the engine to get to it. There's not a lot of room to work with either. If that belt goes on you, so will your engine.

Jul 25, 2008 | 2004 Hyundai Santa Fe

Not finding what you are looking for?
Hyundai Motor 2004 Sonata Logo

296 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6869 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...