Question about Chevrolet C1500

1 Answer

Where is the camshaft and crankshaft position sensors on a 1998 Silverado with a 5.0 Liter 305 V8?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

The camshaft position sensor is the distributor on the back top of engine. The crankshaft position sensor is right behind the harmonic balancer on the front of the engine

Posted on Feb 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0016 and P0017 check engine pop up after i run for 10 to 15 miles?


the common causes for code P0017 are as follows:
  • A faulty cam or crank sensor
  • The cam or crank circuit is open or shorted
  • The timing belt/chain is out of time
  • The cam or crank tone ring is slipped/broken
  • A problem in the VVT system P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor) God Bless! Hope this helps you.

Mar 08, 2016 | Cars & Trucks

1 Answer

Where is the crankshaft position sensor on my 2010 srx 3 liters


Camshaft/Crankshaft Position Sensor Replacement - Cadillac Forums

www.cadillacforums.com/.../261074-camshaft-crankshaft-position-senso...

May 29, 2012 - 8 posts - ‎4 authors
I have a 2004 CTS - 3.6L and am trying to get the camshaft position ... at my local Auto Zone and it simply shows camshaft position sensor A. Code P0340 Camshaft Position Sensor
14 posts
Mar 23, 2013
How to change the camshaft and crankshaft position ...
6 posts
Oct 9, 2011
Where is camshaft position sensor on 2003?
7 posts
Dec 28, 2009
Crankshaft Position Sensor 3.6L 04 CTS
5 posts
Jul 15, 2008
More results from www.cadillacforums.com

2004 Cadillac DTS crankshaft position sensors - YouTube

? 3:22
https://www.youtube.com/watch?v=jbjLJZzF3xA
Sep 16, 2013 - Uploaded by Rogelio Cervantes
Quick overview crankshaft position sensor replacement for a 2004 Cadillac DTS 4.6 liter North Star. ... 2003 Cadillac CTSCrank Position Sensor Part 3 Done!!! - Duration: 8:21. 2LateIWon 8,433 views. 8:21. How To Check .

Jan 16, 2016 | Cars & Trucks

1 Answer

2009 XF 4.2L Where is crankshaft position sensor located?


2009 JAGUAR XF 4.2L V8 Supercharged Auto Parts

https://www.rockauto.com/.../x,carcode,1442330,d,2009_JAGUAR_XF_...
RockAuto has parts for your 2009 JAGUAR XF 4.2L V8 Supercharged and all ... XF 4.2L V8 Supercharged Ignition Parts, Camshaft Position Sensor Crankshaft ...

Jaguar XF Crank Position Sensor - PartsGeek.com

www.partsgeek.com > ... > Jaguar Crank Position Sensor > XF Parts
Oct 1, 2009 - They are available for the following Jaguar XF years: 2010, 2009, 10, 09. ... 10 2010 Jaguar XF Crank Position Sensor 4.2L V8 Intermotor.
Images for 2009 XF 4.2L crankshaft position sensor ...

Dec 11, 2015 | Jaguar Cars & Trucks

1 Answer

How do replace ignition control module in 1998 K-1500 5.0 liter vortec


This system does not use the ignition module used on the DI systems in the past. The VCM controller now controls the ignition control (IC) and bypass functions.
The crankshaft sensor, located in the front engine cover, is perpendicular to a target wheel attached to the crankshaft. The target wheel is equipped with slots situated 60 degrees apart. As the crankshaft rotates, the target wheel rotates past the crankshaft position sensor. The rising and falling edges created by the slots cause a signal to be sent back to the VCM. This signal occurs three times per crankshaft revolution and is referred to as the 3x signal for V6 applications. The signal occurs four times per crankshaft revolution and is referred to as the 4x signal for V8 applications.
The VCM then utilizes this 3x (V6) or 4x (V8) signal in order to provide the correct spark to the engine by way of the single coil driver module. The single coil driver module is basically an electronic switch that when commanded by the VCM, causes the primary coil voltage to breakdown, energizing the secondary coil and providing a spark via the coil wire to the distributor cap. The distributor consists of the following components:
The system consists of the following components:
?€¢
Vehicle control module (VCM)


?€¢
Distributor


?€¢
Ignition coil driver module


?€¢
Ignition coil


?€¢
Crankshaft position (CKP) sensor


Now which part do you want to replace ?

?€¢
Cap and rotor


?€¢
Camshaft position sensor


?€¢
Gear drive and shaft

The camshaft drives the distributor shaft which rotates providing a spark to the correct cylinder by way of the cap and rotor. The camshaft position (CMP) sensor functions much like the crankshaft sensor previously described but provides only a 1x signal to the VCM. That is, for every 2 rotations of the crankshaft, there is 1 rotation of the camshaft. Note that the camshaft position sensor will not affect driveability. The sole purpose of the camshaft position sensor is to provide the VCM with the necessary information for the misfire diagnostic trouble codes (DTCs).

Sep 06, 2015 | 1998 Chevrolet K1500

1 Answer

Where are the camshaft and crankshaft position sensors on 2001 silverado 8.1 V8


pic-1681384701591865649-tmb.jpegCrank shaft sensor
Remove the driver side rear ignition coil bolts. Reposition the coil. Disconnect the crankshaft position (CKP) sensor electrical connector. # Use penetrating oil and allow the oil to soak around the CKP sensor prior to removing the sensor. You're looking at left, rear side of engine.
CAMSHAFT POS.
front side of engine on the drives side about half way up the timing cover, not hard to get to.

Nov 11, 2013 | Chevrolet 3500 Cars & Trucks

1 Answer

Lincoln Ls v8 camshaft sensor fix


Here's a link on your crankshaft position sensor,here's the camshaft one.

Jul 24, 2013 | Cars & Trucks

1 Answer

4x4 v8 1998 dodge truck won't start


well if ur not getting spark and u changed all of the ignition components lets think about the computer in order for the ignition to work you have crankshaft position sensor that fires the fuel injectors and the spark change that and if still nothing then change the camshaft postion sensor that sensor tells the computer that the 1 piston has came all the way up and it tells the crankshaft sensor to do its thing

Feb 21, 2013 | 1998 Dodge Ram 1500 4WD

2 Answers

98 silverado 5.7L camshaft position sensor


ITS ABOVE CRANKSHAFT PULLEY.IT CONNECTS WITH CRANKSHAFT POSITION SENSOR.

Oct 23, 2009 | Chevrolet Silverado 1500 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

678 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...