Question about 1991 Nissan 240SX

1 Answer

1991 nissan 240 sx

I hav a 1991 220sx and everytime i get it into 4th gear right before shifting into 5th gear the vehicle cuts out and then i have to hit the clutch and the gas 2-3 times before it will engage

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I HIT A BUMP AND FUEL PRESSURE WENT TO ZERO. IS THERE A WAY TO BY PASS THE ACCIDENT FUEL SHUNT?

Posted on Nov 22, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lost 5th gear


sounds like you have a problem with your shift linkage check to insure you re installed linkage right make

Dec 05, 2013 | Nissan Cars & Trucks

1 Answer

My 2000 Nissan Xterra will not go into 3rd 4th or 5th gear


In the installation of a new clutch in most instances it is necessary to remove the gear lever from inside the vehicle . Check that you have the end of the gear lever actually situated in the groove that lines up all the shift rails as you may have placed the end outside the groove and can move only one rail. You have given no indication of a clutch problem at this stage so I am sure that is where the problem will be.

Dec 05, 2013 | 2000 Nissan Xterra

1 Answer

Gear shifter cable


sounds like a stretched gear shift cable or the linkage on the tranny may need some adjusting i would start with the linkage first jack vehicle up and do a visual while some one goes through the gears make sure to use jack stands so that the power wheels are off the ground.....good luck

Nov 09, 2013 | Nissan 200SX Cars & Trucks

1 Answer

Cuts out at 2500 rpms and dies on idle


2 possible reasons
1--- failed cat converter blocking the exhaust
2---EVAP system not venting the fuel tank properly
run the fault codes and have an exhaust shop check the at converter

Nov 22, 2017 | 1997 Nissan Pickup

1 Answer

My 1995 sentra shifts fine in all gears but when i accelerate in 4th or 5th gear it the rpms wind up and the car doednt real respond feels like its in the accelerater do i need a new clutch


Sounds like the clutch is slipping. If the clutch is bad, it will slip in high gears (4th & 5th) but seem to work fine in lower gears. Clutch probably needs replaced but have a mechanic check it out first because it's a fairly expensive job. If your clutch is actuated via a cable (not hydraulic), it may just need adjusting.

Dec 10, 2010 | Nissan Sentra Cars & Trucks

1 Answer

91 VOLVO 240 WILL NOT SHIFT INTO 4TH GEAR. WHEN I PRESS THE 3RD GEAR BUTTON ON THE SHIFTER, THERE IS A CLICKING IN THE DASHBOARD


Your overdrive relay is bad,but its just as easy to bypass this relay,and never have this problem again IPB sales an bypass plate.5e0ce8b.jpg

Jun 29, 2009 | 1991 Volvo 240

1 Answer

What is the spark plug gap for 1991 nissan 240 sx and can I find a diagram for the wire harness to the ditributor cap


if you have a 1.6 engine the gap is .041 ths /(1.04mm) if you have a 2.0 engine the gap is .033 ths / (.84mm)

May 30, 2009 | 1991 Nissan 240SX

Not finding what you are looking for?
1991 Nissan 240SX Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...