Question about 2002 Chrysler PT Cruiser

2 Answers

Egr valve how do you change out an egr valve and where is it located?

Posted by on

  • 1 more comment 
  • Anonymous Mar 17, 2014

    Where is the Egr valve location

  • Anonymous Mar 17, 2014

    WHERE IS LOCATED THE
    EGR VALVE

  • Anonymous Mar 28, 2014

    Is it necessary to replace an EGR Valve

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 255 Answers

Hi,the egr valve is located at the intake manifold ,you will see it when you open the hood , it looks like a little space ship, when you get the new one you will have no problem finding it,it is bolted with two bolts and is very easy to install, good luck.

Posted on Aug 24, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How do you change out an egr valve and where is it located?

Posted on Jan 30, 2009

5 Suggested Answers

  • 398 Answers

SOURCE: egr valve location

The EGR Valve Location is typically housed on the intake manifold this schematic may help you
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528008822d

Posted on Mar 07, 2009

chuck943
  • 783 Answers

SOURCE: egr valve location

here is a pic of it.
[IMG]http://i253.photobucket.com/albums/hh43/chuck943/V2903019.gif[/IMG]

Posted on Mar 02, 2009

c17hydro
  • 2984 Answers

SOURCE: Location of EGR Valve

Found the info!!

This Dodge EGR valve is a certain kind of device that is mounted right on your intake manifold which controls the amount of exhaust gasses back into your engine.
On a 2005 Dakota with 4.7 liter engine (non-HO), the EGR valve is located near the intake manifold on the driver's side right up against the firewall. It's hard to spot as it sits lower than the intake manifold. To change it, remove the electrical connector. There's a red tab that needs to be pushed to one side and then you have to squeeze down on a tab to get it free. Using a 13 mm socket, remove the bolt that you can see. I had to use a 3 inch wobble extention and then a 8 inch extension with a deep well socket to reach it with my 3/8 inch ratchet. There's a second bolt that you can't see between the EGR valve and the firewall. With a little trial and error and a lot more luck, you can reach the hidden bolt with the 3 inch wobble extension and a 13 mm deep well socket. Attach the ratchet after the socket is on and remove. This one isn't easy and if there's any Dodge engineers reading this one, a couple of extra inches of clearance between the valve and the firewall wouldn't have killed you no matter what the cost accountants said. With both bolts removed, you should be able to pull out the metal pipe that connects the manifold to the EGR valve out of the manifold (Pull to the right) and then you can lift the valve out. For assembly, the metal pipe connecting the intake manifold the EGR valve has to be removed and reinstalled on the new valve. It's held on with 2 5/16th" bolts. You should put the rear bolt on tight, but leave the front bold loose for the reinstall as some adjustment is necessary to get it put back together and the rear is a pain to tighten when installed. Line up the bolts that attach the valve and get the rear 13 mm bolt (The one you couldn't see on disassembly) started. Do not start the other 13 mm bolt as you'll need to pivot the valve and pipe to the left in order to reinsert the pipe into the intake manifold. Once the pipe is in the intake manifold. Start the other 13 mm bolt and tighten both 13 mm bolts and then the 5/16" bolts holding the pipe onto the valve. Reinstall the electrical connection. Please don't forget to rate!!!!

Posted on Mar 14, 2009

ZJLimited
  • 17970 Answers

SOURCE: egr valve location on dodge ram 2005 4.7

The EGR, or exhaust gas recirculation valve, takes inert exhaust gasses drawn from the exhaust system and reintroduces them into the combustion chamber through the intake manifold. This process lowers the peak combustion temperature and helps combat the formation of Nitrous Oxide (NOx) in the exhaust.

f0255cf.jpg

  1. Separate the intake ducts from the air cleaner assembly by loosening the retaining clamps and pulling the ducts away from the housing.
  2. Disconnect the vacuum line from the air cleaner assembly.
  3. Remove the wing nut that secures the air cleaner housing lid to the base.
  4. Remove both the air cleaner hosing lid and base.
  5. Locate the EGR valve. Look at the front of intake manifold. The EGR valve will be bolted to the intake manifold just in front of the carburetor.
I hope help you with this. Good luck.

Posted on Sep 07, 2009

ZJLimited
  • 17970 Answers

SOURCE: were is the egr valve located for mazda rotege5

2002 Mazda Protege5 with the FS2.0 Motor. The EGR Valve is located below the throttle-body. You must take off the Intake tube to get a good view of it. To replace it I think you might have to take off the throttle-body.

0335fe8.jpg

Fig. Exploded view of the intake manifold assembly with 2.0L (FS) engine

Good luck (remember rated this).

Posted on Jun 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of the EGR Valve


th?id=hn.608027864339644782&w=183&h=146&c=7&rs=1&url=http%3a%2f%2fwww.auto-parts-online.com%2fproducts%2fegr-valve-riviera-regal-electra-caprice-84-87-egv795.html&pid=1.7this is what the EGR looks like, usually near the back of the intake manifold on carbureted vehicles. check the vacuum at the hose before changing the EGR, your vac hose may be leaking instead of a faulty EGR. cost a dollar for vac hose.

Feb 27, 2014 | 1996 Chevrolet Caprice

1 Answer

P 1401 location


Codes don't have a certain location, a code means a problem has occurred in a system of the electronics of the cars fuel control or emission control system.
P1401 NISSAN - EGR Temperature SensorPossible causes- EGR Temperature Sensor harness is open or shorted
- EGR Temperature Sensor circuit poor electrical connection
- Faulty EGR Temperature Sensor
- Malfunction of EGR function, EGRC-BPT valve or EGRC-solenoid valve
- Blocked EGR passages When is the code detected?An excessively low voltage from the Exhaust Gas Recirculation (EGR) temperature sensor is sent to Engine Control Module (ECM) even when engine coolant temperature is low, or an excessively high voltage from the EGR temperature sensor is sent to ECM even when engine coolant temperature is high.
P1401 NISSAN Description The Exhaust Gas Recirculation (EGR) temperature sensor detects temperature changes in the EGR passage way. When the EGR valve opens, hot exhaust gases flow, and the temperature in the passage way changes. The EGR temperature sensor is a thermistor that modifies a voltage signal sent from the Engine Control Module (ECM). This modified signal then returns to the ECM as an input signal. As the temperature increases, EGR temperature sensor resistance decreases.
This sensor is not used to control the engine system. It is used only for the on board diagnosis

Oct 08, 2012 | 2000 Nissan Maxima

1 Answer

How to replace the egr valve.


I want to change the EGR valve Myself in my 2003 Hyundai XG350L anyone know how to do that?

Apr 08, 2012 | 2002 Hyundai XG350

1 Answer

Is there an EGR valve on 01 Jeep Grand Cherokee 4.7 L, and if so where?


The EGR Valve is located on the rear, driver's side of the engine. It's a failry easy job, and you should be able to this yourself.

The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head. An exhaust gas routing tube connects the EGR valve to the intake manifold.

2010-05-30_173844_1.gif
  • Remove electrical connector at top of EGR valve solenoid.
  • Remove tube mounting bolt at intake manifold.
  • Remove two bolts connecting EGR tube to valve assembly.
  • Remove gasket located between EGR tube flange and EGR valve assembly. 2010-05-30_173909_2.gif
  • Remove two EGR valve mounting bolts.
  • Separate valve assembly from engine.
  • Remove and discard metal gasket located between cylinder head and valve assembly.


Sep 30, 2011 | 2001 Jeep Cherokee

1 Answer

How do I install an EGR valve for 2005 dodge durango?


To install the EGR Valve on a 2005 Durango first it is necessary to remove the air intake hoses and palce them to the side. Next, in order to get the EGR valve you will need to remove the windshield wiper motor, which is a pain but necessary to do get to the EGR valve. After removing all of the itemsthat are in the way you will be faced with a task that will try your patience, the EGR valve is located on the right side of the motor, (as if you were facing the motor from the front) just behind and to the rear of the throttle body. After you locate it you will need a rachet with a flexible head because it is fairly difficult to reach otherwise. A mirror and light will also help so you can see what you are doing since the EGR valve is located in such a hard place to see and get to that you will only be able to see part of it while you are removing the screws. After removing the EGR valve, simply reversethe procedure and your done. P.S. I own a 2005 Dodge Durango SLT with a 4.7L engine and I replaced mine this year after a check engine light came on and I checked the code on the OBD. By the way the EGR valve is a pain in the rear to change. Good luck!

Jun 29, 2010 | 2005 Dodge Durango

2 Answers

1988 F-150 4.9 six. Pulled codes and it showed egr valve was not closing. Changed egr valve and now when driving there is a miss when engine warms up. Did not have the miss before I changed egr valve.


Check to make sure you didn't accidentally loosen a spark plug wire or broke/disconnected a vacuum hose.

A trick you can try; spray WD40 around the area you were working in, and see if the idle changes. If the idle changes then the problem is associated with a vacuum leak in that area....look for loose/cracked vacuum line.

Mike...

Nov 20, 2009 | 1988 Ford F 150

3 Answers

EGR problem on 2001 Camry??


Replace filter in EGR Modulator located to the left of EGR valve.
How do you clean the intake port below the EGR valve?

Sep 30, 2009 | 2001 Toyota Camry Solara

2 Answers

Egr valve location on dodge ram 2005 4.7


The EGR, or exhaust gas recirculation valve, takes inert exhaust gasses drawn from the exhaust system and reintroduces them into the combustion chamber through the intake manifold. This process lowers the peak combustion temperature and helps combat the formation of Nitrous Oxide (NOx) in the exhaust.

f0255cf.jpg

  1. Separate the intake ducts from the air cleaner assembly by loosening the retaining clamps and pulling the ducts away from the housing.
  2. Disconnect the vacuum line from the air cleaner assembly.
  3. Remove the wing nut that secures the air cleaner housing lid to the base.
  4. Remove both the air cleaner hosing lid and base.
  5. Locate the EGR valve. Look at the front of intake manifold. The EGR valve will be bolted to the intake manifold just in front of the carburetor.
I hope help you with this. Good luck.

Sep 07, 2009 | 2005 Dodge Ram 1500

2 Answers

2005 Dodge 1500 code p0404 EGR valve.


The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,

  1. Remove electrical connector (5) at top of EGR valve solenoid.
  2. Remove tube mounting bolt (1) at intake manifold.
  1. Remove two bolts (4) connecting EGR tube (1) to valve assembly.
  2. Remove gasket located between EGR tube flange and EGR valve assembly.
  3. Remove two EGR valve mounting bolts (5).
  4. Separate valve assembly (3) from engine.
  5. Remove and discard metal gasket located between cylinder head and valve assembly.
INSTALLATION
  1. Clean area at rear of left cylinder head where it joins base of EGR valve.
  2. Clean EGR tube where it joins EGR valve.
  3. Position new gasket between EGR valve and cylinder head.
  4. Position EGR valve to cylinder head. Install and tighten two bolts (5). Refer to Torque Specifications.
  5. Position new gasket between EGR tube flange and EGR valve assembly.
  6. Position EGR tube (1) to side of EGR valve and into intake manifold.
    1. Install EGR tube flange bolt (1) at intake manifold. Tighten bolt. Refer to Torque Specifications.
    2. Connect electrical connector (5) to top of EGR valve solenoid (2).Do a final tightening of two EGR tube bolts (4). Refer to Torque Specifications

Feb 05, 2009 | 2005 Dodge Ram 1500

Not finding what you are looking for?
2002 Chrysler PT Cruiser Logo

1,324 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...