Question about Chevrolet Aveo

1 Answer

2006 Aveo.Need to get the right side door panel off.Pry off? Pressure pins?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 76 Answers

Just have a look on the door panel and if you can see circle discs wich you can prise off allowing the panel to come off if there are none of these then try slowly prising the panel off being carefull not to lose any clips or damage the panel itself.

Posted on Jul 29, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How to remove door panel from 2006 suzuki grand vitara

The door is afixed with push pins.

Remove the screw that secures the pull handles, then use a thin device between the door panel and the metal frame. slid until you are close to a pin and then apply outward pressure.
Best to start at he bottom or lower outer edge...once the bottom and sides are loose, lift the panel verticaly to release top edge...

Jun 29, 2015 | 2006 Suzuki Grand Vitara

1 Answer

How do I remove the drivers side door panel on a 2006 Chevrolet Aveo?

Most panels today, slide straight up, not pulled out.

Nov 08, 2014 | 2006 Chevrolet Aveo

1 Answer

How do I take inside door panel off

Tools Needed:

Flathead screwdriver (the pointier the end the better)
T30 torx wrench

Removing the panel:

Before the panel can be removed you must start by removing the bolts holding it on.

Begin by locating the black rubber square in the pocket on the arm rest

To remove it wedge a flathead screwdriver under it and pop it up

25120304-etqrlrti5hbclqlowkwdhbst-5-2.jpg Undo the 2 T30 Torx bolts holding the control panel down.

25120304-etqrlrti5hbclqlowkwdhbst-5-5.jpg Next is to remove the control panel. To do so, pry it up with a flathead.

25120304-etqrlrti5hbclqlowkwdhbst-5-9.jpg Once its up, undo the 3 connections and put it somewhere.


25120304-etqrlrti5hbclqlowkwdhbst-5-20.jpg Next pry open the cap in the door handle cubby (if someone can post a way to not break it that would be great)

25120304-etqrlrti5hbclqlowkwdhbst-5-27.jpg Remove the T30 torx bolt behind it.

25120304-etqrlrti5hbclqlowkwdhbst-5-35.jpg Next remove the button thing on the side of the door panel.

25120304-etqrlrti5hbclqlowkwdhbst-5-44.jpg To remove it, push inward on the inner circle and pry it off with a flathead

25120304-etqrlrti5hbclqlowkwdhbst-5-54.jpg To undo the bottom portion of the panel, start by pushing the flathead behind the panel

25120304-etqrlrti5hbclqlowkwdhbst-5-65.jpg Pull the screwdriver away from the door to release the pin. Do this along the bottom of the whole panel until all nine pins have been released.

25120304-etqrlrti5hbclqlowkwdhbst-5-77.jpg Finally before you can remove the panel. Stick the flathead behind the piece holding the tweeter and pop the pressure clip loose.

25120304-etqrlrti5hbclqlowkwdhbst-5-90.jpg To lift the panel off put your hands on the side off the panel and pull the bottom away from the door. Then lift up, releasing the panel from the channel at the top of the door. Lift it over the top of the lock pole thing.
The latch cable will need to be removed next. It is simply held on by a clip.

25120304-etqrlrti5hbclqlowkwdhbst-5-104.jpg Once the cable is released the final thing to do is disconnect the final remaining connections.
Once the connections are disconnected the panel can be completely removed.

25120304-etqrlrti5hbclqlowkwdhbst-5-119.jpg Doing the passenger side door is basically the same. The only difference is that the bolts are in different locations and there are only 2 connections
One of the bolts is in the door handle pocket, just like the drivers side

25120304-etqrlrti5hbclqlowkwdhbst-5-135.jpg Once again i managed to snap the little cover off again.To locate the other 2 bolts, you need to remove the metallic grey trim. Begin by sticking the flathead in the side of it

25120304-etqrlrti5hbclqlowkwdhbst-5-152.jpg Pry along the edges until you can pull it off


25120304-etqrlrti5hbclqlowkwdhbst-5-189.jpg The 2 bolts will be located under neath. Remove each of the 2 T30 torx bolts.


25120304-etqrlrti5hbclqlowkwdhbst-5-230.jpg Just like the driver side, you next need to undo all the clips along the bottom of the panel as well as the little button thing on the side and the pressure clip by the tweeter. Lift it up to release it from the channel and disconnect the cable and the connections.

When putting it all back together, just reverse what you did and it should go back together no problem. Just make sure (this took me awhile to figure out) that when you put the button thing in that you make sure the inner circle is popped out.

25120304-etqrlrti5hbclqlowkwdhbst-5-252.jpg Insert it with it popped out and then push the inner circle in.

Sep 20, 2014 | 2006 Pontiac G6

1 Answer

How do i repaire the door handel to my 1997 dodge avenger i can open it from inside but not on the out side

This is a very mechanical fix. Open the door. Remove whatever screws you can find on the panel, sometimes they are hidden behind little plastic "buttons". Most larger screws are around the armrest and door pull handle. After that the door panel is just pryed off a little at a time. Start at the bottom corner away from the hinge, carefully insert a large screw driver and pry corner. Once you get one corner up you can use a bright light to kinda see what other places you have to pry up. Try to pry in a even pressure, put screwdriver close to hold down pin. These pins are intended to be used once so many times after you get it all open many of the pins will be broken. I've found you can get replacements at autoparts store (red packages called "help") Lowe's has a selection of unique fasteners. With panel off its simply mechanical know how to replace handle. I've never seen a diagram or anything you just have to be good mechanically. Good luck!

Mar 17, 2010 | 1997 Dodge Avenger

2 Answers

How do I replace stoplight bulb. Removed two screws on lens but can't remove lens to replace bulb.

Use a small flat head screwdriver to pry off the lens from the plastic housing. The stop light bulb replacement number you need is: 1157

Dec 22, 2009 | 2006 Chevrolet Aveo

2 Answers

How do I take off the driver's door to fix the loc mechanism?

to remove door panel,carefully pry off trim around door handle,remove plug[s] & screw[s] from armrest,remove screws or pry off speaker grille.bottom & sides of panel is attached with push pins.pry them out & lift panel to release window weatherstripping.not as hard as it sounds once you've done it.a small nail pulling tool works well on push pins

Sep 20, 2009 | 1997 Ford Expedition

1 Answer

How do you remove the door panel in order to access the speaker etc. ?

There should be 2 to 3 screws covered by little plastic covers near the door armrest and door release. Remove those then using a flat head screwdriver carefully pry the panel away from the door. You'll want to move the screwdriver between the door and the panel till you find the push pins and do most of the pry work on each side of the push pins you find. These pins will be difficult to remove but they will release. When you are done you can simply align the door and apply pressure to the pins and re-insert them and the screws.

Sep 04, 2009 | 2001 Jeep Cherokee

1 Answer

Right side half side broke

disconnect outer tie rod and ball joints from wheel hub. remove hub. check for retaining bolts to trans . remove axel u will probably need to use a pry bar

Aug 14, 2009 | 2006 Chevrolet Aveo

2 Answers

Getting driverside door panel off

remove the trim piece around the door handle. there are 4 tabs, one at 12 o'clock, 3 o'clock 6 o'clock and 9 o'clock. remove the 2 screws in the indention for closing the door. carefully remove all of the locking pins in the door. there is a special tool for this but if you are careful and take your time 2 screwdrivers will also work. Start in the lower left corner and slowly pry the panel away. you will be able to see the pins as you are pulling away. slide the screwdrivers on either side of the pin and carefully pry open. once all pins are released the small trim piece by the mirror needs to be removed in the same way. there is one pin only. after the trim piece is removed lift the panel up to release it from the window channel

Jun 28, 2009 | 1999 Chevrolet Tahoe

1 Answer

Fusion door panel removel

There is a fastener behind a circle looking plug behind the inside door handle. Take a small flat screwdriver and pop it off. It will be a torx. The same as the other screws on the door panel. After removing all fasteners start with the bottom of the panel and get your fingers between the panel and pry ou there will be door fasteners that will pop releasing the door. Do this carefully.

Nov 08, 2008 | 2008 Ford Fusion

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides