Question about 1997 Dodge Neon

1 Answer

Neon headlamps I need to convert my UK registered Neon to European lhdrive headlights Who is headlight manufacturer or where I can source them please.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 21,949 Answers

If you are in spain valencia region go to repuestos serca look in phone book,they are available in any large motor factor ,there are two or three manufacturers ,valeo bosch and ,,,cant remember the other one

Posted on Nov 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing headlight for 1994 olds ciera


It depends on which lamps you have? The none-European is like the picture. You use a screw driver of some type and remove that frame, then remove the headlamp frame.

The other type, you get under the hood and remove headlamp bulb connector to remove bulb.

26034627-kx0ho3obetoh5at412oainxa-2-0.jpg

Jan 02, 2016 | Cars & Trucks

2 Answers

I need help troubleshooting the passenger headlight that will not turn on. Story is below


Insure that ground wire for that lamp is good and connections are good. Use multimeter to insure you have voltage to the bulb socket. Trace wires back to headlamp relay cheaking for broken wire.

Jun 26, 2015 | 2005 Ford F-150

1 Answer

I recently had some front drivers side damage to my car. The head light was smashed and the wheel well pushed in far enough that it occasionally rubs against the wheel when I make right turns. I've managed...


Mr Pinske,

The rear running lights aren't on the same circuit as the headlight(s). To get the car legal for
night driving, replace the broken headlight (both need to work to drive legally at night),
and tackle the running lights as a separate project.
First thing to check on the running lights - the bulbs. Why: incandescent light bulbs that are
on at the time of an impact cannot withstand the impact and the filaments can fail, so fixing
your rear running lights may simply be a matter of replacing the two light bulbs.
If the bulbs are ok, your accident has caused a wiring fault, which you will locate
between the ignition switch and the rear running lights.
Here's the manual on how to replace the headlight:

1993 Buick Century
HEADLIGHT REMOVAL & INSTALLATION
Non-European Style
See Figures 1, 2, 3, 4 and 5
  1. Remove the headlamp trim panel attaching screws.

archaeology_17.jpg



Fig. 1: Remove the headlamp trim panel attaching screws

  1. Remove the headlamp bulb retaining screws. Do not touch the two headlamp aiming screws, (at the top and side of the retaining ring), or the headlamp aim will have to be readjusted.


archaeology_18.jpg


Fig. Fig. 2: Remove the headlamp trim panel assembly from it's mounting location

  1. Using a screwdriver, remove the retaining ring screws.
archaeology_19.jpg


Fig. 3: Using a screwdriver, remove the retaining ring screws

archaeology_20.jpg

Fig. 4: Once the retaining ring screws are removed, the ring can be pulled away

  1. Pull the bulb and ring forward then separate them. Unplug the electrical connector from the rear of the bulb.


archaeology_21.jpg


Fig. Fig. 5: Pull the bulb out and unplug the electrical connector
To install:

  1. Plug the new bulb into the electrical connector.
  2. Install the bulb into the retaining ring and install the ring and bulb.
  3. Install the trim panel.
Replacing the European style headlights is a slightly different procedure.

Mar 15, 2011 | 1993 Buick Century

2 Answers

Hi I have a mazda mx5 mk3 from the UK and I am looking to change my headlights in order for me to register my car in France. I need to change the full headlight assembly and was wondering if you could...


try fitting stick on beam correctors on the outside of the headlamps you usally buy them from a mazda dealers parts dept a lot cheaper than fitting headlamps and comply with french and uk law once fitted

Feb 24, 2011 | Mazda MX-5 Miata Cars & Trucks

1 Answer

How do I install a headlight assembly for a 2005 dodge neon


HEADLAMP MODULE REMOVAL
  1. Release hood latch and open hood.
  2. From behind bumper fascia, remove bolt holding outboard end of module to fender.
  3. Loosen bolts holding inboard end of module to radiator closure panel.
  4. Remove bolt holding grille to headlamp module.
  5. Remove bolts holding top of module to upper crossmember Headlamp Module
  6. Disengage wire connector from headlamp and parking lamp sockets.
  7. Separate headlamp module from vehicle.
INSTALLATION Reverse the preceding operation.

Feb 18, 2011 | 2005 Dodge Neon

1 Answer

I need to replace the entire headlamp assembly units on both the driver and passenger sides of a Mercury Cougar V6 2.5l. The car was built in 2000 and badged as a "FORD COUGAR" where it was...


It will cost a fortune to buy brand new. You can find lot of second hand ones on ebay.co.uk and ebay.com. Lot of ebay sellers in UK wont ship overseas. If you are in USA then you can find on US ebay and there are heaps available. Use a headlight restoration kit and the light will become brand new again. If you need further info, let me know.

Jan 05, 2011 | 2002 Mercury Cougar

1 Answer

Am desparately trying to find French headlights for my (currently) UK registered Daewoo Korando (a 1999 V-reg) in order to re-register in France. Can you suggest any possible suppliers? Many...


hi tracey,use lhd converter kit (from dealers in UK) then you NEED to go to a mainland european dealer to get headlights,dont be supprised if they havnt got a clue what a Korando is,as GM used different names for different countries.....you will need to SEE the same car to find out if its supplied in France.(or any other mainland country, unless you have seen the same car over here)regards,
geoff.England.

Oct 22, 2010 | Daewoo Korando Cars & Trucks

2 Answers

I need to replace front headlamp lens peugeot 405 1992


phone the scrapyard you bought it from, they had to take it out and having had your business, will hopefully be helpful!

Feb 21, 2009 | 1989 Peugeot 405

1 Answer

Passenger front headlamp bulb replacement required


Remove the carpet covering the inside near the headlight. Remove round rubber plug. (pull hard, the plug has NO WIRES coming out of it) Use the 5mm wrench that is in the toolkit. (toolkit is behind the spare tire). Turn the wrench 180 degrees and the whole headlight assembly will loosen. Pull out the whole assembly. Remove plastic end cap. The high beam, low beam and parking bulbs are all right inside that cover. Just did my 2002 for the first time. This is also covered in the manual if you have one. Thanks, max327@aol.com

Feb 10, 2009 | 2000 Porsche Boxster

1 Answer

How to install 2003 dodge neon headlight assembly.


  1. Disconnect and isolate the battery negative cable.
  2. Remove screws attaching headlamp module to upper crossmember.
  3. Remove headlamp module from vehicle.
  4. Disconnect wire connectors from back of headlamp module.
  5. Remove headlamp module

Jul 02, 2008 | 2003 Dodge Neon

Not finding what you are looking for?
1997 Dodge Neon Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...