Question about 2000 Toyota Land Cruiser

1 Answer

2000 toyota land cruiser door power lock

All doors lock up when i turn off the ignition, also the reading light does not work when the ignition is off.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 979 Answers

This is normal if I'm reading this right. The door locks are supposed to pop up when you turn off the key when in "child proof" mode. The reading lamp is wired to prevent low battery conditions by only operating when the engine is running. Did you just get the car?

Posted on Jul 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toyota land cruiser


Clean or replace the door switch.

Sep 07, 2014 | Toyota Land Cruiser Cars & Trucks

1 Answer

Immobilizer light will not go off when key inserted, Lock smith said my computer was not responding, Toyota wants to replace computer but that's 1200 bucks and I want to make sure that this will fix the...


YOU MUST HAVE MASTER KEY:
1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.

5. Within 3 seconds the power door locks should cycle automatically indicating successful
entry into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
B. Immediately after letting go of the lock and unlock buttons, press the lock button by
itself and hold for 2 seconds. Within 3 seconds, the door locks should cycle once
indicating successful programming. If the door locks do not cycle, or cycle twice.
repeat steps A and B in step 6 as your remote has not been accepted.
C. Repeat steps A and B in step 6 for each new remote.

7. Close drivers door.

Sep 18, 2013 | 2001 Toyota Land Cruiser

1 Answer

Toyota Land Cruiser ignition question.


Sounds like the connector between the lock cylinder and the switch is broken.
You would need to remove the key switch to find out.

May 14, 2013 | 2000 Toyota Land Cruiser

1 Answer

I've own a 95 land cruiser, When i open the driver door or any to get in the vehicle...all the lights within the dash starts to flicker and a control pace. When i stick the key in the ignition and start...


This is a security problem, try using the key to unlock the pass/side door and see if it does this if it doesnt then the switch on the lock on the driver door is bad, the switch is to shut down the alarm.

Nov 05, 2010 | 1995 Toyota Land Cruiser

1 Answer

Lost remote and like to program new remote. HELP. 2000 prado vx.


1. Start with the following conditions: you are in the vehicle a. Key is out of the ignition
b. Drive door is open ( all other doors are closed)
c. Driver door is unlocked (other door locks don't matter)

2. Insert the key into the ignition (don't turn it) and pull it out.
3. Perform these steps within 40 seconds: a. Cycle the power locks 5 times. Use an even pace and try
to go relatively fast.
b. Close, then open the drivers door.
4. Perform these steps within 40 seconds: a. Cycle the power locks 5 times (same as before).
b. Turn the ignition to ON then back to OFF.
c. Turn the ignition to ON then back to OFF.
d. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should cycle (automatically)
indicating successful entry into programming mode. Return to step 1
if the locks do not cycle at this point.

6. Perform these steps within 40 seconds: a. Press the LOCK and UNLOCK buttons on the transmitter
simultaneously for 1 second.
b. Immediately after letting go of the lock and unlock buttons,
press the lock button by itself and hold for 2 seconds.
Within 3 seconds, the door locks should cycle ( LOCK then
UNLOCK) once-- indicating successful programming. If
the door locks don't cycle, or cycle twice. Repeat steps
6a and 6b--this remote has not been accepted.
c. Repeat steps 6a and 6b for EACH transmitter that will
operate the vehicle. Including any old transmitters.

7. Close the driver door.
Good luck and hope this helps.

Nov 04, 2009 | 2000 Toyota Land Cruiser

1 Answer

Remote works but doors don't lock/unlock


Check the remote battery or replace. Check all fuses. If you need to reprogram, try this.

key not in ignition.
driver door open-others closed
driver door unlocked

1-insert and remove key from ignition two times

2-close and open driver door two times

3-insert and remove key once from ign.

4-close and open drvr door twice

5-insert key into ign.,then close driver door

6-turn key to on (not start) then off, twice
this is rewrite mode,have all remotes to reprogram
it will clear any lost remotes.

7-remove key from ignition,the door locks should cycle twice.if not start over.it may take a few tries.

8-press lock/unlock together and hold for a second

9-release,and press lock on remote,the door locks will cycle confirming program.continue to do other remotes you have,steps 8 and 9.if only one in possesion,you are done.

to end mode open door or insert key into ig.you can do up to 4 remotes.read this a couple of times to get the sequence down.there are time restraints,but if you go in order it will work.do not wait more than a second b/t each step and you will be ok.i know from experience that you can do this as fast as you can and it will enter mode.if steps out of order or you wait to long it wont.print this and have in lap,read ahead of what you are doing.good luck

Jun 13, 2009 | 2000 Toyota Land Cruiser

1 Answer

Remoe dont lock or unlock the doors. hazard lights, indicators and horn dont work.


You might have a blowen fuze. I would check that first. If it is blowen and continues to blow after replaceing it, then you have a short somwere in the wiring.

May 19, 2009 | 2000 Toyota Land Cruiser

1 Answer

Remote door entry not working


could be that the remote lost memory during battery change may need to reprogram

Apr 28, 2009 | 2000 Toyota Land Cruiser

Not finding what you are looking for?
2000 Toyota Land Cruiser Logo

230 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...