Question about Nissan Maxima

1 Answer

Irregular idle on maxima 2000 scan tool codes 1302 and 0302

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 1,894 Answers

Can you please explain your problem in detail. please

Posted on Jul 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have p1320 code in my 2000 maxima


code p 1320 refers to ignition signal---circuit malfunction===causes wiring---ignition coil/ module---ignition system---crank position sensor---ECM
the light will remain until it is reset by the scan tool
At this point from your description of cooling down , the fault may be in the ignition module ( over heating from internal problem)
The crank sensor may have a similar problem

Dec 20, 2015 | 2000 Nissan Maxima

1 Answer

I have 2007 maxima 3.5 i did tune up, at first it idled around 2000rpm, cleared the code for high idle and now its surging? Any ideas, i thought the computer would would set the idle back to normal.


Nissans require a special relearn procedure that is done with a professional, bidirectional scan tool.It only takes a few minutes but you need the right equipment.

Aug 13, 2013 | Cars & Trucks

1 Answer

HOW DO YOU CALIBRATE A MASS AIR FLOW AENSOR FOE 2000 MAXIMA


you do not calibrate a mass air flow sensor. If you are trying to adjust the idle it can be doen but the right way to do it is perform "Idle Volume Learn" You can only do this with a nissan scan tool called a consult.

Jul 02, 2011 | 2000 Nissan Maxima

1 Answer

My maxima is idling quickly, and it continues to do so whilst driving even after the motor has warmed up. what do I need to do to fix this??


First check for any disconnected vacuum hoses. If good, have the car scanned at a local auto parts store to see if any pending codes are present. There may be a problem with the idle air control motor or the throttle position sensor.

Apr 23, 2010 | 2000 Nissan Maxima

1 Answer

2000 maxima with no overdrive and code po744 .no tranny slipage in1-2 shift or 2-3 shift,very smooth.the od light works and comes on and off when the od button is pushed.


This code indicates a mechanical problem inside the transmission. Likely in the valve body or the torque converter. He is a description of the cause and a list of possible problems. To diagnose this you need a scan tool capable of reading the trans control module and a pressure guage to read the fluid pressure.

Nov 27, 2009 | 2000 Nissan Maxima

1 Answer

Anyone know how to get the OBD codes from a 2000 Maxima without the use of the OBD II tool?


i dont think you are able to get the codes without a scanner but if you go to autozone, kragen, or pepboys they should let you scan it for free

Aug 11, 2009 | 2000 Nissan Maxima

1 Answer

Car idle revs


If the check engine light is on, take the car to an autoparts store and have them use a scan tool to retrieve any fault codes stored in the computer. Most parts stores will perform the scan at no charge. Getting the codes will go a long way toward identifying what the problem is. I would look at a faulty idle air control valve, but getting the codes should end the speculation. Hope this helped and best wishes.

Aug 01, 2009 | 2000 Honda Civic

3 Answers

Not idling


Try checking your idle air control valve and see what happens

Jul 19, 2009 | 1996 Nissan Maxima

1 Answer

2000 maxima with 84,000 miles


the code means the converter on the side cyliner # 2 is not working like it should ,to check to be sure you need a scan tool and data from the front and rear o2 sesor cannot mimic each other if they do the converter is bad ,there are aftermarket converters for that car but they dont preform as well as the factoy one .


Jul 13, 2009 | 2000 Nissan Maxima

1 Answer

I'm the original owner of a 2005 vw beetle, less than 11,000 miles, but out of mfg warranty. MIL light has started showing, with a very irregular idle. Any idea what could be causing this?


Best thing to do is if there is an Auto Zone near to you, have them scan the can for the DTC code which should be related to your irregular idle. There to many things that can cause the idle problem you have and with the DTC code, that should explain or at least lead us to the cause of the irregular idle. Auto Zone all so scan free of charge and can give you the step by step instructions to repairing the car to have it run 100% again. Good luck and keep me posted, be glad to help

Jul 05, 2009 | 2005 Volkswagen New Beetle Convertible

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...