Question about 1991 Chevrolet Cavalier

1 Answer

Need a wiring diagram for 1996 chevy astro - 1991 Chevrolet Cavalier

Posted by on

  • Anonymous Dec 16, 2008

    manual

  • Anonymous Feb 24, 2009

    when i turn a/c on my driving lights get brighter and wipers come on

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

1991 chevy cavalier wont start

Posted on Jan 10, 2009

5 Suggested Answers

SOURCE: 1996 chevy express van audio wiring diagram

go to www.the12volt.com

Posted on Aug 31, 2008

  • 1 Answer

SOURCE: 2000 Chevy Astro van rear ac

astro van 2000 rear a/c switch

large orange power 13.8 volts pin G
small orange pin A
blue pin B
not used pin C
not used pin D
gray pin H
yellow pin F
black pin E

Posted on May 03, 2009

c17hydro
  • 2984 Answers

SOURCE: need to replace 1991 chevy astro van break pads

The following procedure requires the use of a C-clamp and slip-joint lock pliers.

  1. Siphon off about 2/3 of the brake fluid from the master cylinder reservoirs.

CAUTION The insertion of thicker replacement pads will push the piston back into its bore and will cause a full master cylinder reservoir to overflow, possibly causing paint damage. In addition to siphoning off fluid, it would be wise to keep the reservoir cover on during pad replacement.

  1. Raise and support the front of the vehicle on jackstands. Remove the wheels.
When replacing the pads on just one wheel, uneven braking will result; always replace the pads on both wheels.
  1. Install a C-clamp on the caliper so that the frame side of the clamp rests against the back of the caliper and so the screw end rests against the metal part (shoe) of the outboard pad.
  2. Tighten the clamp until the caliper moves enough to bottom the piston in its bore. Remove the clamp.
  3. Remove the 2 Allen head caliper mounting bolts enough to allow the caliper to be pulled off the disc.
  4. Remove the inboard pad and loosen the outboard pad. Place the caliper where it will not strain the brake hose; it would be best to wire it out of the way.
  5. Remove the pad support spring clip from the piston.
  6. Remove the 2 bolt ear sleeves and the 4 rubber bushings from the ears.
  7. Riveted style brake pads should be replaced when they are worn to within 1/32 in. (0.8mm) of the rivet heads; bonded style pads should be replaced when they are worn to no less than 1/32 in. (0.8mm) of the backing plate.
  8. Check the inside of the caliper for leakage and the condition of the piston dust boot.
To install:
  1. Lubricate the 2 new sleeves and 4 bushings with a silicone spray.
  2. Install the bushings in each caliper ear. Install the 2 sleeves in the 2 inboard ears.
  3. Install the pad support spring clip and the old pad into the center of the piston. You will then push this pad down to get the piston flat against the caliper. This part of the job is a hassle and requires an assistant. While the assistant holds the caliper and loosens the bleeder valve to relieve the pressure, obtain a medium pry bar and try to force the old pad inward, making the piston flush with the caliper surface. When it is flush, close the bleeder valve so that no air gets into the system.
Make sure that the wear sensor is facing toward the rear of the caliper.
  1. Place the outboard pad in the caliper with its top ears over the caliper ears and the bottom tab engaged in the caliper cutout.
  2. After both pads are installed, lift the caliper and place the bottom edge of the outboard pad on the outer edge of the disc to make sure that there is no clearance between the tab on the bottom of the shoes and the caliper abutment.
  3. Place the caliper over the disc, lining up the hole in the caliper ears with the hole in the mounting bracket. Make sure that the brake hose is not kinked.
  4. Start the caliper-to-mounting bracket bolts through the sleeves in the inboard caliper ears and through the mounting bracket, making sure that the ends of the bolts pass under the retaining ears of the inboard shoe.
  5. Push the mounting bolts through to engage the holes in the outboard shoes and the outboard caliper ears and then threading them into the mounting bracket.
  6. Torque the mounting bolts to 37 ft. lbs. (50 Nm). Pump the brake pedal to seat the linings against the rotors.
  7. Using a pair of slip-joint locking pliers, place them on the notch on the caliper housing, bend the caliper upper ears until no clearance exists between the shoe and the caliper housing.
  8. Install the wheels, lower the vehicle and refill the master cylinder reservoirs with brake fluid. Pump the brake pedal to make sure that it is firm. If it is not, bleed the brakes.

Posted on Oct 11, 2009

ZJLimited
  • 17970 Answers

SOURCE: i need the engine wiring diagram for chevi

1996 Chevrolet Cavalier 2.2L SFI OHV 4cyl

This is a sample for an 1996 2.2L (VIN 4) engine schematic...
4773406.jpg

You can find more details and the Repair Guide about your model in autozone.com (free register). Select the Year, Make, Model and Engine for access.

I hope help you with this (remember rated this help) Good luck.

Posted on Oct 14, 2009

Puppet03
  • 172 Answers

SOURCE: horn does not work. relay and fuse good, need wiring diagram

Had the same problem myself i just replaced the horn itself.

Posted on Oct 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 Chevy van fusebox location


Donald, You did not state the model, so I posted the link for the models I found for chevy van fuse box. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Interior Fuse Box Location 1990 1996 Chevrolet G20 1994 Chevrolet G20...
Blown Fuse Check 1990 1996 Chevrolet G20 1994 Chevrolet G20 Chevy Van 4 3L...
fuse box diagram 1990 chevy astro van pdf 1 Docs Engine com
1990 Chevy van fusebox location Google Search

Jul 27, 2016 | Cars & Trucks

1 Answer

I have a 1998 chevy astro van and need a wiring diagram for wires under the dash.


Any repair shop with Mitchell On Demand can print the diagram for you. It may cost you a few dollars, however.

Nov 05, 2014 | 1998 Chevrolet Astro Van

1 Answer

Location sending unit


If it is a 4.3 L engine, it is located at the right hand side of the distributer as you are looking in at the engine. It looks somewhat like a mushroom W/ a wire going iinto it.

Jun 02, 2014 | 1996 Chevrolet Astro

1 Answer

Wiring diagram chevy


http://www.bbbind.com/technical.html
free wiring diagrams and TSB's for every make and model.

Jan 21, 2014 | 1998 Chevrolet Astro

1 Answer

1996 Chevy Astro Van--"Will not


I would check the rotor very carefully. They tend to burn a hole through the plastic under the center tab. It's hard to see sometimes. The spark follows that path instead of to the wire terminals. You may just want to try a new distributor cap and rotor.

Aug 08, 2011 | 1996 Chevrolet Astro

1 Answer

1994 astro ext will not start


fuel pump relay is under the hood in the fuse/relay box. information is in your owners manual.
when was the last time you replaced the fuel filter, maybe its plugged?

Nov 02, 2009 | 1994 Chevrolet Astro

1 Answer

Where can I get a free download?


your installing an aftermarket cd player in place of factory radio?
it would be best to buy the harness adapters. they plug into the factory harness and will tell you what all the wires are. harness is usually only 10-15 dollars. here is the diagram also.7834529.gifa4b592f.gif

Oct 02, 2008 | 1997 Chevrolet Venture

1 Answer

2000 Chevy Astro van rear ac


astro van 2000 rear a/c switch

large orange power 13.8 volts pin G
small orange pin A
blue pin B
not used pin C
not used pin D
gray pin H
yellow pin F
black pin E

Sep 15, 2008 | 2000 Chevrolet Astro

Not finding what you are looking for?
1991 Chevrolet Cavalier Logo

322 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...