Question about 1999 Chevrolet K1500

1 Answer

TRUCK STARTS OCCASIONALLY, WHEN IT WON'T START I HAVE NO SPARK & NO FUEL INJECT, INTO TBI, REPLACED ECM,USED OLD CHIP, ALSO REPLACED COIL,KNOCK SENSOR,FUEL RELAY,IGNITION SWITCH AND IN TANK FUEL PUMP

Posted by on

  • Anonymous Mar 29, 2014

    Car is starting but won't turn over. There is fuel in the tank

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a '99 suburban and had the same problem. Couldn't figure it out. Took it to the dealer, and it was a engine disable type module. There is a sensor in the ignition switch that "sees" the key (connected to this module), and allows the engine to start/run. Could be the sensor or the module. My problem was the module. Seem to remember costing about $500 with troubleshooting, parts, labor. Good luck.

Posted on Sep 27, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1990 chev silverado that won't start has fuel pressure has spark injectors won't inject changed injectors could the throttle position sensor being bad cause the injectors not to work


No. If it is throttle body injectors(TBI), Check the plugs for power with the key on. No power, check fuse and wiring. If you have power, use a test light at the injector plug on both pins, crank the engine, the light should flash. No flashing, check the wire from the plug the the engine control module(ECM) If it is good(less than 5 ohms and not shorted) replace the ECM. TBI Has only one driver in the ECM, fires both injectors. Multi port injectors(MPI) has several drivers in the ECM. Unlikely they all died at the same time. Unless you have recently done some welding on the truck. Being it is a 90. I would pull all the fuses and visually inspect them. This also get rid of any corrosion problems. Fixed many problems by pulling a good fuse.

May 21, 2016 | Cars & Trucks

2 Answers

I have a 1987 chevy S10 4x4 xcab pickup . it just died one day i rebiult the TBI and put a new computer in it and new coil in . Have checked all the fuses . and it will not start .do you know what i


Check if you have spark (coil or ignition problem) Next consider what you did when rebuilding the TBI as there may be parts that will only operate in one way or settings that have to be adjusted. Lastly is the new ECM compatible with the system (immobiliser) Use a scanner to reset the ecm program

Nov 22, 2014 | 1987 Chevrolet S-10 Pickup

1 Answer

My 98 gmc 1500 V8 5.0l won't start. Has good spark


Spray starting fluid into the air intake of the engine, if it starts and you have fuel pressure you have no injection or injector pulse as we call it. Check ECM fuse one and two for continuity if it starts with fluid..

May 25, 2012 | 1998 GMC Sierra

1 Answer

Won't start


Check the fuel injectors, with the key on one side of the two wire connector will have battery voltage, if none is present then check the ECM fuses in the underhood fuel box.

Jun 22, 2017 | 1999 GMC Sonoma

1 Answer

90 chevy 350 tbi crank no start, truck was started driven around the block parked it and let it idle a few minutes before shuting it off, the next day it would not start, it acts like timing is off and is...


You first need to check the fuel pressure, an easy way to access this is to buy a can of spray starting fluid, spray it into the TBI throttle valve and if the truck starts and dies you have no fuel pressure. Replace the fuel; pump, and make sure you get the right pump, it is a low pressure system.

May 19, 2017 | 1990 Chevrolet C1500

1 Answer

Did engine swap on 97 1500 all new sensors, fuel pump. also new ecm. have spark and fuel pressure. truck will not start.


remove the eprom out of the old computer and check the numbers and see if they are different if they are swap out the eprom. You can get to it by removing the two screws out of the top of rhe computer and you will see the chip. also does it have the coil pack or single coil?

Jan 19, 2010 | 1997 Chevrolet K1500

4 Answers

97 gmc sierra no fuel no spark replaced ign module and pickup coil still no spark


1996 GMC 1500 Pickup.
Replaced Coil, Dist cap/Rotor, Ign Mod & pick-up.
All showed to be bad with OHM meter.

20A ECM-B fuse keeps blowing out and I'm afraid to burn these new parts up....

ANY IDEAS OUT THERE???

Mar 31, 2009 | GMC Sierra 1500 Cars & Trucks

Not finding what you are looking for?
1999 Chevrolet K1500 Logo

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...