Question about 2002 Dodge Neon

1 Answer

Camshaft sensor replacement I need to know how to.

Posted by on

  • Anonymous Oct 21, 2008

    camshaft sensor location on motor

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 512 Answers

Drivers side of the head..bolted to the head at the back of the front cam shaft

Posted on Oct 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace camshaft position sensor ?


need more information since each manufacturer puts the sensor in different spots --generic answer --the following link shows different vehicles sensors being replaced
How to replace camshaft position sensor in your vehicle Camshaft Position Sensor Replacement Replace Camshaft Position Sensor Yahoo Video Search Results

Aug 31, 2016 | Cars & Trucks

2 Answers

Camshaft sensor in 2009 hhr


You should probably take the car to a reliable shop or the dealer for that problem because those codes pertain to the intake and exhaust camshaft position actuator valves - not the sensor itself. It's more than just simply replacing the sensor for that problem.

May 06, 2014 | 2009 Chevrolet HHR

1 Answer

1996 camshaft sensor


You don't need to be at tdc to replace the camshaft sensor.

Mar 08, 2014 | Cars & Trucks

1 Answer

2006 frontier camshaft position sensor


If you do not know where the Camshaft Position Sensor is located, then it would be safe to assume that you have not properly tested the sensor or the circuits that operate the sensor. Therefore, you cannot possibly know for sure that it even NEEDS to be replaced...so why are you looking to replace it?

Nov 20, 2011 | 2006 Nissan Frontier

1 Answer

Where is the camshaft position sensor located in my 06 dodge magnum? And is there anything special i may need to know in order to replace it myself?


The camshaft position sensor, it is on the passenger side in the front on the engine block, it will have a grey connector attached.

To replace:

Disconnect the negative battery cable.
Remove 10mm bolt and remove camshaft sensor.
Unplug sensor, apply dielectric grease to new sensor and plug in, apply a small amount of grease to o-ring, replace into block and tighten bolt.
Reconnect battery cable....that's it, your done.

Thank you for useing FixYa, please take time to rate me.

Jun 29, 2011 | Dodge Magnum Cars & Trucks

1 Answer

Can i replace the camshaft sensor on my sebring


the camshaft sensor is not sold separately for a 2.5 engine,it is mounted in the distributor and you would have to replace the whole distributor!

Dec 05, 2009 | 2000 Chrysler Sebring

3 Answers

How can i fix code po344 intrepid 2002


Before replacing the cam shaft sensor,verify good terminal tension and connection at the sensor.This carline has a history of faulty connections here and this could fixya before spending the cash on car parts....good luck

Jul 24, 2009 | 2004 Dodge Intrepid

1 Answer

Car won't start


The camshaft sensor on this engine was located on the passenger side of the engine. You will need to remove the serpentine belt, and you can get to it by removing the inner fender or splash guard and get to it that way. I went down from the top. There are two sensors, one is a CRANKSHAFT sensor and other is a cam sensor. Make sure you know which is which. The crankshaft sensor is at the bottom of the engine, the camshaft is right by the water inlet. It is held in by 1 or 2 bolts. If your car is throwing the code for the camshaft sensor, just a heads up. I replaced the sensor and the sensor detects magnets installed on the camshaft. The engine kept throwing the code and came to find out one of the magnets had come off the end of the cam. I am telling you this just in case you go through the replacement and still end up with the code. the camshaft sensor is not too hard to replace, it's tight but it can be done. unbolt the old and bolt in the new. Make sure you disconnect battery before tackling this project. Hope that help some..

May 29, 2009 | 1991 Buick LeSabre

2 Answers

Need help finding camshaft position sensor


2.0L 2.4L Removal The camshaft position sensor is mounted to the rear of the cylinder head.

Remove the negative battery cable. Disconnect the PCV hose and reposition Disconnect electrical connectors from the camshaft position sensor. Remove camshaft position sensor mounting screws. Remove sensor.Loosen screw attaching target magnet to rear of camshaft and remove magnet.
Instalation The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.
- Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
- Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
- Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins. - Connect the PCV Valve hose. - Connect the negative battery cable.
2.7L V6 Removal
The camshaft position sensor is mounted in the front of the head.

Disconnect electrical connector from sensor. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
Without pulling on the connector, pull the sensor out of the chain case cover.

Installation - Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
- Attach electrical connector to sensor.

Good luck and hope this helps





May 02, 2009 | Dodge Stratus Cars & Trucks

1 Answer

Cam Shaft Sensor Problems


Had the same problem before on my 04 Neon SXT...camshaft sensor is on left side of engine block, take out the battery and to the left of it (face car) is the camshaft position sensor. To change it you'll have to move a few hoses but its plan to see there on the left side of the engine...pretty easy remove and replace. Fixed my problem of car not going above 2k RPM when i replaced the sensor.

Dec 15, 2008 | 2004 Dodge Neon

Not finding what you are looking for?
2002 Dodge Neon Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...