Question about 1992 Pontiac Bonneville

1 Answer

1992 pontiac bonneville se

Does the engine have to be lifted to remove the water pump?

Posted by on

1 Answer

No, in fact that water pump is fairly easy to change.

Posted on Aug 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to find the cmp sensor?


Should be just below the water pump. Look on the passenger side of the front of the engine. You should see some wires connected just below the water pump.

Jun 26, 2014 | 1992 Pontiac Bonneville

1 Answer

Diagram or manual of starter in 1992 pontiac bonneville


Chilton manual at any auto parts store will have the information you need

Jan 04, 2012 | 1992 Pontiac Bonneville

1 Answer

My 1992 SE sputters when accelerating and sometimes stalls out


It is a clear case of the fuel pump malfunctioning. As not enough fuel is being pumped when accelerating, the engine sputters and stalls. The pump could be needing servicing. Nothing serious. Happens. So, please have it serviced.

Aug 24, 2010 | 1992 Pontiac Bonneville

2 Answers

I am trying to locate the crankshaft sensor on a 92 pontiac bonneville se


It is by the crankshaft pulley.It is behind the pulley and you have to remove the pulley to replace it.There is a special tool for installing the new one.If you look through the pulley you should be able to see it.Hope this helps.Good luck.

Feb 24, 2010 | 1992 Pontiac Bonneville

2 Answers

I need a serpentine belt diagram for a 1997 pontiac bonneville se 3.8L - no turbo


0900c152800b19a9.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 8: You can use a box-end wrench on the pulley nut to rotate the tensioner ...


0900c152800b19aa.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 9: ... then remove the belt from the pulleys


0900c152800b19ab.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 10: Serpentine drive belt routing and removal - 3.8L (VIN L) engine shown, VIN C similar


0900c152800b19ac.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 11: Make sure to note the drive belt routing prior to removing it - 3.8L (VIN K) engine shown


0900c152800b19ad.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 12: Drive belt removal on a 1992-95 supercharged engine
To install:
Be sure the belt is aligned into the proper grooves of the accessory drive pulleys.
  1. Lift the tensioner, and install the belt onto pulleys. Make sure the belt is routed properly.



0900c152800b19ae.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 13: Many vehicles have a label you can check to be sure the belt is installed and routed correctly
  1. For 1996-99 vehicles, raise and safely support the vehicle. Install the engine mounting bracket lower spacer, stud and nut.
  2. For 1996-99 supercharged engines, perform the following:
    1. Attach the connector to the crank sensor.
    2. Install the right-hand splash shield, then carefully lower the vehicle.

  3. Install the belt guard or reservoir.
  4. Connect the negative battery cable.

Nov 18, 2009 | 1997 Pontiac Bonneville

1 Answer

I have a 1992 pontiac bonneville 3.8 car and on startup makes a h


Time for a new fuel sock and fuel pump, pump is in the tank.

Sep 29, 2009 | 1992 Pontiac Bonneville

2 Answers

1998 pontiac grand am se 2.4 i need to find and replace water pump


this is a very big job, I have the same car, it is located at the bottom rear of the engine, you need to remove the timing chain housing, timing chain turns the water pump, and also remove the exhaust manifold, takes no less than 6 hours in a shop on a lift

Jul 01, 2009 | 1995 Pontiac Grand Am

1 Answer

1992 bonneville transmisson won't engage


not likely possibly the cover for torque converter may be loose. if rattling coming from pass. side may be belt tensioner/or water pump. to check shut engine off remove serp. belt check water pump pulley for play by wiggling back an forth do same with belt tensioner. check trans fluid level while on level surface engine warm&running tranny in park. some gm cars have had problems with crank shaft pulleys making rattling noise also.

Oct 03, 2008 | 1992 Pontiac Bonneville

Not finding what you are looking for?
1992 Pontiac Bonneville Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...