Question about 2003 Hyundai Santa Fe

2 Answers

Change a clutch - 2003 Hyundai Santa Fe

Posted by on

  • Anonymous Aug 01, 2008

    hello i am trying to remove a gearbox but it wont come out, any ideas everything is disconnected transfer box removed but still will not come past flywheel. any help will be helpful.

  • Filemoni Vagana Aug 21, 2008

    hello i am trying to remove a gearbox but it wont come out, any ideas everything is disconnected transfer box removed but still will not come past flywheel. any help will be helpful.



    how to seperate the Gearbox from the Engine its a manual gearbox, because I need to change my clutch. I've opened all the nuts around the gearbox but still it doesnt seperate, I've tried to pull out but its still stuck. Hopefully someone can help me with this. Or to open the whole topics is how to change the disc clutch of a gearbox.

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Hyundai Master
  • 70,387 Answers

Remove the drive shaft 1st, and the transfer case if it is a 4X4, then with the transmission supported remove the cross member and mount, disconnect any wiring and all linkage on trans, the shift linkage may have to be removed from top side in truck, but it has to come out. Make sure everything top and bottom is removed then remove that bolts that attach trans to back of engine, carefully pull trans back, and lower down on a floor jack, then unbolt clutch cover and remove the disc and cover, remove the engine flywheel and take it to a machine shop to have it resurfed, if you don't do this the new clutch will ****/shudder on release. Make sure you support the truck with good jack stands at all four corners, you will need to get it as high up in the air as possiable, at least 3 feet. reverse above to reinstall. Good luck and be careful!

Posted on Jul 28, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Hi i guess you have solved the mistery by now you have to remove the clutch arm nut and arm ( it has a master spline so you cant get it wrong) on the cross shaft as this has a PULL type of clutch and the arm has to undo as you pull the gear box out it will NOT come out unless you do to replace do the reverse operation regards ray w QLD OZ

Posted on Apr 06, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

My clutch intermittently shudders/vibrates when depressed. Is that a sign it is failing?


The short answer is YES. Most likely a warped clutch, will need a new pressure plate and clutch disk and in the worst case fly wheel replaced or machined. The good news is that it could last for awhile before complete failure or until you get annoyed and wish to replace it.

Apr 13, 2015 | 2005 Hyundai Tucson

1 Answer

Loud snapping noise heard when changing gears


From the way you've described it your gear stick linkages maybe on there way out. When changing gear does the car resist getting into gear?

If it's more of a crunching sound then I would try double de clutching, to do this you need to:
change gear as usual but instead of holding down the clutch throughout the gear change hold it down to take the vehicle into neutral then release the clutch then push the clutch down again and change into desired gear.
To change down it's basically the same principal but you push down the clutch to put the vehicle into neutral then push the throttle down just to pitch revs then release the throttle and push the clutch down to change into your desired gear, if it won't go in to gear easily then rather the throttle until it does.

You can go onto youtube and search for double de clutching and I'm sure some results will come up

hope this helps!

Apr 30, 2014 | 2004 Nissan Altima

1 Answer

How to change clutch in a '08 Shelby GT 500


You should change the slave cylinder when doing the clutch.

A lot of good information here:
http://www.teamshelby.com/forums/index.php/topic/72113-advice-on-new-clutch-for-shelby-gt500/

Jun 17, 2013 | Cars & Trucks

1 Answer

Hyundai excel 1996 have to double clutch to change gears


Where is clutch engaging? close to firewall or up high on pedal. If up high, your clutch needs replacing, Low, your clutch is ok, maybe throwout bearing is bad or air in system or not adjusted correctly

Apr 05, 2013 | Cars & Trucks

2 Answers

My renault scenic i hard to change gear


possible clutch cable or cluth itself, check the clutch cable first to see if its stretched, i didnt check and put a new clutch in ,and wasted £250 , try euro car parts for cheapest clutch cable.

May 17, 2010 | Cars & Trucks

1 Answer

My clutch for the compressor is bad. 98 nissan froniter 4cyclinder . Is it possible to change clutch without removing compressor? Or should I just change entire compressor out?


It is possible to change the clutch out if you can find someone who will sell them. Check out some place like surpluscenter.com, check out the power transmissions tab, and click on clutches, and you may find one. Otherwise, it's difficult to find the clutches by themselves. You'll need a puller to get the old one off.

May 12, 2010 | 1998 Nissan Frontier

1 Answer

Clutch change


hi it seems your clutch is losing pressure,it works like a shock, known as a hydrolic clutch, i recommend you change it asap.

Feb 05, 2009 | 2000 Volkswagen Beetle

1 Answer

Clutch won't engage--cannot shift


hydraulic clutch needs servicing or needs bleeding like a brake system wont work with air in the lines neither will hydraulic clutch's. you shouldnt have to change the clutch just service the slave cylinder ,that should give you back some pedal to use..you might want a mechanic to bleed it or have it replaced.

Jan 05, 2009 | 1994 Mercury Tracer

Not finding what you are looking for?
2003 Hyundai Santa Fe Logo

398 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...