Question about Chevrolet Beretta

2 Answers

Leaking clutch fluid drips on ground but hoses and master cylinder are ok what do i do

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check ur slave cyinder

Posted on May 23, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Change the slave cylinder!!!!!!!!!!

Posted on Apr 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where to check clutch fluid level on 2004 mini


the clutch fluid reservoir is at the clutch master cylinder or is an extension of the brake master cylinder
look for a hose from the clutch master cylinder to the brake master cylinder reservoir

Dec 28, 2015 | 2004 Mini Cooper

2 Answers

My clutch seems to have gone out tonight. The clutch is very easy to push to the floor...and it pops back....there's no pressure at all. The clutch fluid is leaking from the hose. Could this be the...


it could be either the master cylinder or the slave cylinder,it could also be the clutch pressure plate check the master & slave cylinders first because if it's the pressure plate the gear box will have to be removed to replace the pressure plate, even if you are uncertain it is most likely cheaper to replace the master & slave cylinders than it would be to replace the pressure plate.....hope this helps......cheers.

Aug 31, 2011 | Saturn Vue Cars & Trucks

2 Answers

My 1996 eclipse keeps losing clutch fluid. have to keep replacing fluid. do not see any fluid leakage on the ground. what could be causing this?


Your car has a clutch master & slave cylinder and fluid can be running down hose or leaking slightly that you may not notice fluid spots. One or both need to be replaced.

Feb 28, 2011 | Mitsubishi Eclipse Cars & Trucks

1 Answer

Are the brake master cylinder and the clutch slave cylinder interconnect in some way? I'm told that the slave cylinder get its fluid from the master cylinder.


The brake system and the clutch master cylinder have the same fluid tank, look at the brake master cylinder fluid tank, on the right hand side about half way up is a hose that goes over to the clutch master cylinder, if fluid level is not above this hose the clutch will stop functioning. If the clutch slave cylinder, mounted on the front side of transmission bellhousing, leaks then the clutch will stop functioning. The slave cylinder has a bleed screw, check these items and fill and bleed as neccessary. Hope this helps, let me know.

Jul 28, 2010 | 1995 Ford Escort

2 Answers

Clutch goes all the way to the floor without resitance on my daughters 2004 sunfire. there is fluid on the ground and when I checked fluid level it appeared to be empty


Examine carefully to locate exact point of leak. Could be the hydraulic line, a connection between line & slave cylinder or master cylinder, or a bad slave cylinder. Once you identify the point of leak, I can help you with repair info if needed.

Jun 04, 2010 | 2004 Pontiac Sunfire

1 Answer

The clutch was lose and when you pushed on it it went to the "ground". My husband checked and it was out of the "clutch fluid" (sorry...I'm a girl!) and we did notice that there is a little bit of...


the clutch pedal is hooked up to the clutch master cylinder which is connected to the clutch slave cylinder at the transmission by a metal line. If the slave cylinder is leaking (most common) replace it usually --two bolts and a metal line fitting. the clutch system will have the air purged which can be done by gravity bleeding. reattach the components open the bleeder valve on the slave cylinder and keep topping off the clutch mastercylinder with fluid untill the stream of fluid out of the slave cylinder no longer has bubbles. test peddal stiffness and repeat as needed--a vaccum pump can also be used to draw the fluid through the system

Aug 10, 2009 | Isuzu Rodeo Cars & Trucks

5 Answers

Stuck clutch pedal on a Mazda B series truck


Replace both clutch slave and master cylinders, and bleed well. I've also had this happen.

Jul 11, 2009 | 1988 Mazda B2200

1 Answer

Where is the clutch valve located on a 95 honda accord


clutch master cylinder is located drivers side firewall,right next to brake master cylinder. it has small shot glass size fluid resevoir mounted above it,fluid is fed through hose down into clutch master. clutch master cylinder has a rod mounter on ft of it that goes through firewall and attaches to clutch pedal under dash . clutch slave cylinder is mounted on ft passenger side of transmission assy. most common leak is from master cylinder,you would be able to look under dash ,follow clutch pedal up to where it attatched to clutch master pushrod.follow that rod to wear it meets up to a small 1 1/2" or so rubber boot.fluid will be leaking from that boot if master is leaking.

Jul 03, 2009 | 1995 Honda Accord

3 Answers

Leaking clutch fluid Where is the slave cylinder"..I have been told to look at the slave cylinder because I do not see fluid under the car.


Slave cylinder should be on the left side of the bellhousing (follow the line from the clutch master if necessary) If you don't see fluid but you have lost some, also check where the rod from the pedal goes through the firewall to the master...they often leak there and will not drip on the ground.

May 30, 2009 | Hyundai Motor 2002 Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...