Question about 1995 Dodge Intrepid

1 Answer

I have had my 1995 Intrepid for a few yaers. I seem to be having trouble with my turn signles. and fourway flashers. I've replaced fuses, bulbs andthe flasher unit under the dash board.I don't know what else to try.

Posted by on

1 Answer

Yeah try checking the 2 little wires on the pos sid batt terminal / mine corroded so i cleaned and reattached them and it solved the prob
thx

Posted on Jul 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mazda b2000 1986 truck turn signls dont work replaced fuse flashers work but no turn signles


You do not replace any parts, until you find a problem

The manual you have, has to be a wiring diagram book

You study that & then do some testing to find the problem

Dec 05, 2014 | Mazda Cars & Trucks

1 Answer

My turn signals don't work and I've checked the bulbs, fuses & flasher.


About all that is left on the list is the turn signal switch.
Do you have power in and out of the switch ?

Feb 04, 2013 | 1995 Buick Skylark

1 Answer

Turn signals blin continually


There is only a few things that can cause blinkers to blink continually, meaning if your saying they wont shut off, Normally it is the blinker flasher or a fuse. Sometimes it can be in the blinker switch itself. I first would check the flasher, and turn signl fuse. If the blinker stays on and does not flash, still can be bad flasher or fuse or a ground problem, You would then have to check the wires around area where there contact to the tail light blinkers and front blinkers. But first start as said earlier with checking flasher fuse, switch and fuse. Mike

Jan 16, 2012 | 1995 Cadillac DeVille

1 Answer

Can,t get signal or flashers to work on 1997 Dodge Intrepid


I assume you've checked the Fuses :p Obviously that hasnt worked and the bulbs and lights haven't worked either... SO try this????
Open the driver's side door and examine the end of the dash for an access panel. Behind the access panel are fuses and flashers. There are two flashers inside the access panel for controlling the turn signal and the hazard lights. You can distinguish them apart from each other by turning on the hazards or the turn signal and feeling for the clicking. If you turned on the hazards, then the flasher that is clicking is the hazard flasher.
Remove the turn signal flasher from the dash and reinstall the new flasher into the vacated slot in the dash. Close the access panel and start thetruck . Check the turn signals for proper operation and make sure the hazards work as well.


Please let me know how it goes
  • Jan 07, 2012 | Cars & Trucks

    1 Answer

    I have a 2004 jeep wrangler the running lights come on and dirrectionals come on also, after checking fuse's and bulbs and replacing brake switch,i still have no brake lights,can someone help me


    you have a bad ground the brake light are independent of the rest of the lights if the turn signals work and the brake lights don't you have a bad ground blowen fuse or your turn signals are not grounded properly so the turn signal lights may be dim or erritic in nature you can also check the blinker switch for it can be shorted (remember that there are two 1 for the turnsignals & 1 for the fourway flashers

    Mar 09, 2010 | 2004 Jeep Wrangler

    1 Answer

    1997 Chevy Tahoe both turn signals stopped working


    Sounds like the flasher unit to me. Normally the emergency flasher and turn signal are separate.

    Jul 21, 2009 | 2001 Chevrolet Tahoe

    3 Answers

    Turn signal problems


    Turn signal flasher should be plugged in on fuse panel.

    Jun 02, 2009 | 1995 Dodge Intrepid

    1 Answer

    Rear flasher not working front flasher flashing rapidly


    with the blinker on hold the socket in your hand and wiggle on the bulb and see if it starts to blink. if so then you have a bad socket that needs replaced or sometimes can be cleaned and apply electrical grease. if you cant get the bulb to blink then get in vehicle and watch the signl indacator while putting pressure on the selector in which ever direction your having problems with. if you get it to work properly by doing this then you will need a new switch .

    Jan 29, 2009 | 2003 Ford Explorer

    Not finding what you are looking for?
    1995 Dodge Intrepid Logo

    Related Topics:

    144 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dodge Experts

    yadayada
    yadayada

    Level 3 Expert

    60541 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21927 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6811 Answers

    Are you a Dodge Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...