Question about 2002 Mitsubishi Galant

1 Answer

Car radio and cd player locked

Although I have the unlock password (4 digit numeric) which contains a zero and a nine whereas the buttons only show numbers 1 to 6. How do I punch in the numbers especially the 0 and the 9 - Mitsubishi Magna 2002 Australian model

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The 4 digit code is entered using station preset buttons "1" through "4". Each time you press one of these presets the appropriate code digit increments from 0 to nine. As an example, say the code is 5193, press the "1" preset 6 times (zero is displayed on the first press, 1 on the second, etc.), press the "2" button twice, the "3" button 10 times and the "4" button 4 times. The code 5193 will be displayed on the unit.

To accept the code, press the CD button and if the code is correct the unit will come back to life.

Posted on Aug 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I unlock the radio on a 2001 Saturn ls300


I need more information. When the radio is on, does the display show 4 lines like this. ---- or does it spell the word "lock" on the display. If it says "lock" , you must take it to a G.M. dealer .
If it shows the dash lines, then turn off the radio.Turn the key to "run". Hold the preset buttons 5 & 6 down for 5 seconds or so until you see the ----. Using the seek /scan button, enter 0000.If it doesn't unlock, then some other 4 digit code was previously entered. Off to G.M. you must go.

Aug 02, 2014 | 2001 Saturn L-Series

1 Answer

When i try to turn my radio on it says loc hoow do i unlock it?


Does your GM car or truck Radio display LOC and does not turn on? Chevrolet, Buick, Pontiac, GMC, Cadillac, Oldsmobile vehicles used a theft system to lock the radio when power is lost. This system was used from the ealy 1990's to the early 2000's.

Instructions:
  1. If your radio displays the word LOC, you can retrieve a set of factory numbers in the radio that enable you to get a backup unlock code. If the radio says INOP, you will have to leave the key in the "ON" position, or let the car run for at least 1 hour before you attempt any unlock procedure. INOP means a secondary theft lock due to too many false attempts to unlock the radio.
  2. Looking at the face of your GM Delco radio, hold down the preset buttons 1 & 4 OR 2 & 3 (Depending on year and model) for approximately 10 seconds or until a set of 2 or 3 numbers comes up on the display. Write the numbers down.
  3. Next press the AM / FM button. A new set of 3 numbers will now show. Write these numbers down. You will then need to call a 1-800 phone number with these numbers to get the unlock code. There are many sites on the internet that can get it for you- for a small fee. Or, try calling your local GM Dealer and ask for them to do it. Many times they will do it for free. It only takes a minute.
  4. Once you have the unlock code, enter it by pressing the MIN button until the display shows the last 2 digits of the unlock code, then press the HR button until the first 2 numbers or shown. Then press the AM / FM button to enter the code. The radio will now display SEC, and normal function is restored.
Also, its possible that you need RESET your GM Radio; this is the procedure: While performing maintenance on your car, you may disconnect the radio from the battery in your GM vehicle. GM cars contain Delco radios that are protected by Theftlock, which locks the radio after it has been disconnected from a power source. Iit can only be reset and unlocked with a car-specific security code. Identifying the security code for your GM vehicle is the only way to reset the car radio and disable the Theftlock protection device.

Instructions:
  1. Turn on your car. Your Delco radio will show "LOC" in the LED display.
  2. Press and hold down both the second and third preset buttons. Hold these buttons down for at least six seconds.
  3. Write down the two- or three-digit code that appears in the LED display.
  4. Press the AM/FM button on the radio.
  5. Write down the next two- or three-digit code that appears in the LED display. You should be left with either a four- or six-digit number. Turn off your car.
  6. Call the Delco radio automated customer support line at 1-800-537-5140.
  7. Press "1" and then press the pound sign. The automated voice should respond "Invalid code, try again."
  8. Enter the number 139010 into your phone and then press the "*" sign.
  9. Enter the four- or six-digit number you wrote down from Steps 3 and 5, and then press the "*" button.
  10. Write down the four-digit code given by the automated voice.
  11. Turn on your car. Enter the Delco unlock code using the procedure outlined by your GM owner's manual. Normally, the unlock code is entered with the "HR" and "MN" buttons on your radio.
  12. Press the AM/FM button. If you have entered the code correctly, your LED display will read "SEC" and the radio will be unlocked.

Also can check your Does your GM car or truck Radio display LOC and does not turn on? Chevrolet, Buick, Pontiac, GMC, Cadillac, Oldsmobile vehicles used a theft system to lock the radio when power is lost. This system was used from the ealy 1990's to the early 2000's.
jQuery('.intro .thumbnail').each(function(i,e){ jQuery(e).find('img').one('error',function(){ jQuery(e).remove(); }); });
Instructions:
  1. If your radio displays the word LOC, you can retrieve a set of factory numbers in the radio that enable you to get a backup unlock code. If the radio says INOP, you will have to leave the key in the "ON" position, or let the car run for at least 1 hour before you attempt any unlock procedure. INOP means a secondary theft lock due to too many false attempts to unlock the radio.
  2. Looking at the face of your GM Delco radio, hold down the preset buttons 1 & 4 OR 2 & 3 (Depending on year and model) for approximately 10 seconds or until a set of 2 or 3 numbers comes up on the display. Write the numbers down.
  3. Next press the AM / FM button. A new set of 3 numbers will now show. Write these numbers down. You will then need to call a 1-800 phone number with these numbers to get the unlock code. There are many sites on the internet that can get it for you- for a small fee. Or, try calling your local GM Dealer and ask for them to do it. Many times they will do it for free. It only takes a minute.
  4. Once you have the unlock code, enter it by pressing the MIN button until the display shows the last 2 digits of the unlock code, then press the HR button until the first 2 numbers or shown. Then press the AM / FM button to enter the code. The radio will now display SEC, and normal function is restored.
Also, its possible that you need RESET your GM Radio; this is the procedure: While performing maintenance on your car, you may disconnect the radio from the battery in your GM vehicle. GM cars contain Delco radios that are protected by Theftlock, which locks the radio after it has been disconnected from a power source. Iit can only be reset and unlocked with a car-specific security code. Identifying the security code for your GM vehicle is the only way to reset the car radio and disable the Theftlock protection device. jQuery('.intro .thumbnail').each(function(i,e){ jQuery(e).find('img').one('error',function(){ jQuery(e).remove(); }); });
Instructions:
  1. Turn on your car. Your Delco radio will show "LOC" in the LED display.
  2. Press and hold down both the second and third preset buttons. Hold these buttons down for at least six seconds.
  3. Write down the two- or three-digit code that appears in the LED display.
  4. Press the AM/FM button on the radio.
  5. Write down the next two- or three-digit code that appears in the LED display. You should be left with either a four- or six-digit number. Turn off your car.
  6. Call the Delco radio automated customer support line at 1-800-537-5140.
  7. Press "1" and then press the pound sign. The automated voice should respond "Invalid code, try again."
  8. Enter the number 139010 into your phone and then press the "*" sign.
  9. Enter the four- or six-digit number you wrote down from Steps 3 and 5, and then press the "*" button.
  10. Write down the four-digit code given by the automated voice.
  11. Turn on your car. Enter the Delco unlock code using the procedure outlined by your GM owner's manual. Normally, the unlock code is entered with the "HR" and "MN" buttons on your radio.
  12. Press the AM/FM button. If you have entered the code correctly, your LED display will read "SEC" and the radio will be unlocked.

Also can check 1999-Pontiac-Firebird-Owners-Manual (page 163), there are several information about to lock and unlock.


Hope this help (remember comment and rated this).

Apr 06, 2010 | 1999 Pontiac Firebird

1 Answer

Unlock procedure for vw/audi


audi gamma cc type


1e2fb0f.jpg The following is the procedure to re-activate the radio if the display shows "SAFE". It is important that the procedure be followed in the correct order.

  1. Turn on radio. The radio display shows "SAFE".
  2. Press the FM1 and AM buttons simultaneously and hold until "1000" shows on the display. Release the buttons. Do NOT press these buttons again, otherwise the radio will consider "1000" to be the code.
  3. Use Preset buttons 1 ... 4 to enter the four-digit code number from your radio card. Preset button 1 corresponds to the first digit, Preset button 2 corresponds to the second digit, etc. Each press of the button increments the number by 1.
  4. Once the code shown on the display is correct, press the FM1 and AM buttons simultaneously and hold until the word "SAFE" appears in the display, then release the buttons.
  5. The radio should unlock and be usable shortly afterwards.
  6. If an incorrect code is entered, the word "SAFE" appears, first flashing and then continuously. You can repeat the above steps to unlock the radio once more, the number of attempts will be shown in the display. If an incorrect code is entered again, you radio will be locked for about one hour. After one hour - the radio must stay on and the key must remain in the ignition lock - if the display goes out, the you can repeat the above procedure to unlock again. The cycle - two attempts, one hour lock-up - still applies.
  7. If you lose your radio code, contact your Audi dealer.




audi delta






0cf92c2.jpg

The following is the procedure to re-activate the radio if the display shows "SAFE". It is important that the procedure be followed in the correct order.

  1. Turn on radio. The radio display shows "SAFE".
  2. Press the FM1/2 and DX buttons simultaneously and hold until "1000" shows on the display. Release the buttons. Do NOT press these buttons again, otherwise the radio will consider "1000" to be the code.
  3. Use Preset buttons 1 ... 4 to enter the four-digit code number from your radio card. Preset button 1 corresponds to the first digit, Preset button 2 corresponds to the second digit, etc. Each press of the button increments the number by 1.
  4. Once the code shown on the display is correct, press the FM1/2 and DX buttons simultaneously and hold until the word "SAFE" appears in the display, then release the buttons.
  5. The radio should unlock and be usable shortly afterwards.
  6. If an incorrect code is entered, the word "SAFE" appears, first flashing and then continuously. You can repeat the above steps to unlock the radio once more, the number of attempts will be shown in the display. If an incorrect code is entered again, you radio will be locked for about one hour. After one hour - the radio must stay on and the key must remain in the ignition lock - if the display goes out, the you can repeat the above procedure to unlock again. The cycle - two attempts, one hour lock-up - still applies.
  7. If you lose your radio code, contact your Audi dealer.

Mar 29, 2010 | 1997 Audi A4

1 Answer

Cd player showing locked


You will need to see a dealer to unlock and reset the codes need to recover the radio. Possible power lose?

Jul 19, 2009 | 2005 Chevrolet Malibu

1 Answer

I brought my son a 1997 Audi, and the radio is in safe mode, can anyonr help me get the code?


  1. Turn on radio. The radio display shows "SAFE".
  2. Press the P.Scan and RBDS buttons simultaneously and hold until "1000" shows on the display. Release the buttons. Do NOT press these buttons again, otherwise the radio will consider "1000" to be the code.
  3. Use Preset buttons 1 ... 4 to enter the four-digit code number from your radio card. Preset button 1 corresponds to the first digit, Preset button 2 corresponds to the second digit, etc. Each press of the button increments the number by 1.
  4. Once the code shown on the display is correct, press the P.Scan and RBDS buttons simultaneously and hold until the word "SAFE" appears in the display, then release the buttons.
  5. The radio should unlock and be usable shortly afterwards.
  6. If an incorrect code is entered, the word "SAFE" appears, first flashing and then continuously. You can repeat the above steps to unlock the radio once more, the number of attempts will be shown in the display. If an incorrect code is entered again, you radio will be locked for about one hour. After one hour - the radio must stay on and the key must remain in the ignition lock - if the display goes out, the you can repeat the above procedure to unlock again. The cycle - two attempts, one hour lock-up - still applies.
  7. If you lose your radio code, contact your Audi dealer.

Jun 22, 2009 | 2002 Audi A6

1 Answer

I have a 1999 Audi A6.


Entering anti-theft code The following is the procedure to re-activate the radio if the display shows "SAFE". It is important that the procedure be followed in the correct order.
  1. Turn on radio. The radio display shows "SAFE".
  2. Press the P.Scan and RBDS buttons simultaneously and hold until "1000" shows on the display. Release the buttons. Do NOT press these buttons again, otherwise the radio will consider "1000" to be the code.
  3. Use Preset buttons 1 ... 4 to enter the four-digit code number from your radio card. Preset button 1 corresponds to the first digit, Preset button 2 corresponds to the second digit, etc. Each press of the button increments the number by 1.
  4. Once the code shown on the display is correct, press the P.Scan and RBDS buttons simultaneously and hold until the word "SAFE" appears in the display, then release the buttons.
  5. The radio should unlock and be usable shortly afterwards.
  6. If an incorrect code is entered, the word "SAFE" appears, first flashing and then continuously. You can repeat the above steps to unlock the radio once more, the number of attempts will be shown in the display. If an incorrect code is entered again, you radio will be locked for about one hour. After one hour - the radio must stay on and the key must remain in the ignition lock - if the display goes out, the you can repeat the above procedure to unlock again. The cycle - two attempts, one hour lock-up - still applies.
  7. If you lose your radio code, contact your Audi dealer.

Mar 02, 2009 | 1999 Audi A6

1 Answer

Locked radio and cd player


GM DELCO THEFTLOCK RADIO UNLOCK CODE:
1. Press and hold presets 2 and 3 for about 5 to 10 seconds until you
get 3 digits on your display. This is the first 3 of 6 digits you will
need, so write 'em down.
2. After doing step one and writing down the code, immediately press
the
AM/FM button to get the last 3 of the 6 numbers you'll need, and write
'em down. (if you wait too long between steps 1 and 2 and the LOC code
displays again, just start over).
3. Call this number, it's a prerecorded message, so don't worry about
having to talk to anyone...1-800-537-5140. The voice will ask if
you're
calling for Chevy, Pontiac, Cadillac, etc... When you here him tell
you
to press "2" for Pontiac, press 206010 and hit the # key. He'll ask
you
for the 6 digit code that you've written down. Enter that and press
the
* key. He will then give you a code, and the option to get additional
4
digit codes, but one should be sufficient.
4. Follow the normal procedure in your owners manual for unlocking the
radio with your new code...press the hour set button on your radio
until
you get the first two numbers of the code, then press the minute set
button until you've entered the last two numbers. Immediately press
the
AM/FM button once the correct code is entered and the code SEC or
"secured" will be displayed on the display screen. Now, just turn the
radio on, and your ready to roll.
There is an additional step you can take to remove all codes from the
radio and start from scratch by entering your own personalized 4 digit
code so that it won't get you in a pickle again! Just repeat step 4
and
you should get a display screen that reads ---. This means the code is
out, and you can now program your own code. Of course, once you
receive
the 4 digit code from the GM recorded message, just keep it in a safe
place, because you can use that same code again and again should you
have any more problems with it in the future. Good luck, and yes, it
does work.

Sep 08, 2008 | 1998 Buick Park Avenue

3 Answers

Unlock antitheft code for 2004 chevy impala


Radios in the 2004 Impalas are tied to the vehicle's VIN through the computer, so it may be somewhat difficult to get the code. However, the following steps should work:

1. Press and hold the buttons for presets 1 & 4 (may be 2 & 3). The word "SEC" should show.
2. Press the "MIN" button. "000" should be displayed.
3. Press the "MIN" button again to have the second two numbers appear. Record these numbers.
4. Press the "HR" button for the first two numbers to appear. Record these numbers. -- Note: Your number sequence should be the numbers from the "HR" button followed by the numbers from the "MIN" button.
5. Call 1-800-537-5140. This will get you to the GM unlock code automated line. Ignore the prompt and enter "202108#". Next enter your code (remember, HR then MIN) followed by the * key. For example, 1234*. A 3 or 4 digit code will be given to you. If you get a code such as 0532, drop the zero when entering it into your radio.
6. Enter the code into the radio IAW the applicable manual.

May 28, 2008 | 2004 Chevrolet Impala

6 Answers

Locked renault clio 2001 cd/radio player!


to enter your code when the cd player displays error leave cd player switched on and after 20 mins or so i will display 0000 then you will be able to enter your code this happens when some 1 has entered the wrong code

May 17, 2008 | 2000 Renault 181

Not finding what you are looking for?
2002 Mitsubishi Galant Logo

266 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...