Question about 1994 Chrysler New Yorker

1 Answer

HOW TO REPLACE HEADLIGHTS ON 2000 CHRYSLER LHS

Posted by on

  • nikkicarroll Nov 08, 2008

    cant get headligh out to change low beam bulb

  • Anonymous Dec 20, 2008

    same problem, any thoughs

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 594 Answers

ATTN: NIKKICARROLL

here is how to replace the bulb in your vehicle


  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the module halves.
  5. Disengage the wiring from the headlamp bulb.
  6. Remove the retaining ring from the back of the headlamp bulb.
  7. Pull the bulb from the lamp.
To install:
  1. Push the bulb into the lamp.
  2. Install the retaining ring to hold the bulb in the lamp.
  3. Engage the wire connector to the back of the headlamp bulb.
  4. Place the module into position on the vehicle.
  5. Install the screws to hold the module to the vehicle.
  6. Install the radiator closure panel sight shield.
  7. Check the headlamp alignment and operation.
HOW TO REPLACE HEADLIGHTS ON - 88176gb1.gif Exploded view of the fog lamp with the bulb removed
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as needed to gain access to the headlamps.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the halves.
  5. Remove the fog lamp wire connector cover.
  6. Disconnect the wires from the fog lamp bulb.
  7. Disengage the retainer clip holding the bulb to the fog lamp.
  8. Remove the bulb from the fog lamp.
To install:
  1. Place the bulb into position in the fog lamp.
  2. Engage the retainer clip to hold the bulb to the fog lamp assembly.
  3. Attach the wire connectors to the fog lamp bulb.
  4. Install the fog lamp wires connector cover.
  5. Place the module halves together.
  6. Install the screws to hold the headlamp module halves together.
  7. Install the radiator closure panel sight shield.
  8. Verify the fog lamp operation and alignment

ATTN: WDSNEED1

Removal & Installation 88176g87.gif Remove the screws retaining the headlamp module to the mount adapter
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp fasteners.
  3. Remove the screws holding the headlamp module to the mount adapter.
  4. Separate the headlamp module from the mount adapter.
  5. Disengage the wiring from the headlamp and foglamp.
  6. Remove the headlamp from the vehicle.
To install:
  1. Attach the wires to the headlamp and foglamp assembly.
  2. Place the headlamp module into position on the mount adapter.
  3. Install the screws to hold the headlamp module to the mount adapter.
  4. Install the radiator closure panel sight shield.
  5. Check the headlamp alignment and operation.

Posted on Apr 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 chrysler lhs and i need a diagram of the ignition coil pack as in a firing order


For just a few dollars you can get the "Haynes Automotive" manual for the L.H.S. that will have what you need, plus so much more. It is written for the average person and has all the wiring diagrams and even walks you through the engine rebuild. If you love your L.H.S. like I do mine, then it is worth the tiny, tiny investment. I would dig mine out for you but this is a better solution. You can get it online, or at ANY decent Auto Parts store. If you REALLY want me to dig mine out, hit me back and I will.

Mar 19, 2014 | 2000 Chrysler LHS

1 Answer

How do u fix the window brake light in a 2000 chrysler lhs?


you go into trunk and up by the trunk light, you will see a row of plastic push ins, holding the lining up. just pull 3 or 4 of these out, and you can reach up in and twist the two upeer brake light sockets out to replace the bulbs. just did mine, both bulbs were burned out.

Mar 02, 2011 | 2000 Chrysler LHS

1 Answer

2000 Chrysler LHS- Key won't turn! Tried to hotwire it, but seems it's all electronic? HELP!


Well hopefully you didn't mess any of the wiring up by trying to hot wire it. But most likely the tumblers in the lock cylinder are worn out. If you replace the ignition switch it should solve the issue.

Feb 03, 2011 | 2000 Chrysler LHS

1 Answer

Replace thermostat on a 2000 chrysler lhs. where is it ?upper hose? lower hose?


the thermostat is in the housing where the top radiator hose goes onto the motor .....cheers

Aug 14, 2010 | 2001 Chrysler LHS

1 Answer

Replace cooling fan


To start out what way does it look like it comes out? There will be three nuts or bolts two on the top and one on the bottom it could be the other way around if you have any other questions email me at mallanapril@msn.com good luck

Apr 07, 2010 | 2000 Chrysler LHS

1 Answer

Replaced cracked radiator in 2000 Chrysler LHS but car still overheating. What could be the problem?


fix the radiator first.because coolant temperature sensor need to be in antifreeze.when antifreeze get up to 190 degrees. the coolant sensor act as a thermostat.it resistance decrease then the pcm will command cooling fans to run.if antifreeze low the coolant temperature sensor not going to work. engine is going to over heat.

May 29, 2009 | 2000 Chrysler LHS

2 Answers

Replaced cracked radiator in 2000 Chrysler LHS but car still overheating. What could be the problem?


I had the same problem. My Chrysler LHS kept overheating. I had the thermostat changed out first and it didn't help. Then I had the water pump changed out and still did no good. Then changed out the radiator, still overheated. Come to find out the people that changed my thermostat put it in backwards. Evidently, the thermostats for these cars look different from all the others and people are not sure how to put them in. I took mine to a Chrysler dealer and they fixed it for me.

Apr 15, 2009 | 2000 Chrysler LHS

2 Answers

How do you replace the headlight bulb on a 2001 chrysler lhs.


This can be done buy popping the hood and removing the bulb from the rear of the headlight housing. don't screw with the housing because, its leveled for optimal sight range.

Jan 28, 2009 | 2000 Chrysler LHS

1 Answer

Replacing headlamp on 2000 lhs how to


There are two bolts that hold the assembly in place to the radiator support. Pull these (they're long bolts) and the lamp forward. That's all there is to it. I own an Intrepid and these cars are very similar.

Dec 24, 2008 | 2000 Chrysler LHS

Not finding what you are looking for?
1994 Chrysler New Yorker Logo

533 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...