Question about 2000 Ford Windstar

1 Answer

Right Indicator Light (Amber Color) not working

Dear Expert:

My Ford Windstar 2000's Right Indicator Light (Amber Color) and the flasher not working. First I changed the bulb then I changed the fuse (15 amp) as specified in the book but it is still not working. All other lights and flasher for other three corners are working fine.

What should I check next or what could be the problem that I can solve myself. Please help. Thank you.


Posted by on

  • 2 more comments 
  • ezumalato Nov 20, 2008

    the light amber ABS is starting why????

  • Anonymous Nov 29, 2008

    right front blinker does not flash all others work bulb is good fuse is good contacts are good not the only one with this problem with 2000 ford windstar

  • Anonymous Dec 10, 2008

    Same exact problem. All other turn/parking lamps work except for right front. Makes people mad when I can't signal. I tell them "It's a Ford". New bulb and fuse no help. Clean terminals too. ????????????????

  • Anonymous Dec 26, 2008

    I have same problem. Checked Fuse, bulb, sockect everything looks OK. Do not know what to do.



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 702 Answers

Check the inside of the light socket for corrosion and make sure the light bulb is making a good contact in the socket. Use a test light and make sure there is power going to the socket as well.

Posted on Jul 28, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Ford falcon au 2 indicator and hazard light fuses keep blowing

faulty hazard/flasher relay
or the column stalk is faulty

2012 fixya answer on the realy
Where do find the flasher unit in 2000 au ford falcon



Sep 26, 2013 | Cars & Trucks

1 Answer

Need fuse lay out for a 2000 ford windstar. milage

Go to a local library and check out the Chilton series for 2000 Ford Windstars.
Good luck... its a Ford.

Jun 16, 2010 | 2000 Ford Windstar

1 Answer

Turn indicator light flashes quickly. bulbs fine

The quick flash is a fault detection for a burnt out bulb. If bulb is good, check bulb socket. Inspect for corrosion. If needed, replace bulb socket. Check bulb socket connector. Check if fuse. Check emergency flashers ( most cars have a separate circuit).

Jul 09, 2009 | 2000 Ford Windstar

1 Answer

Turn signals/flashers not working

The flasher functions for this vehicle are performed by the Front and Rear Electronic Modules.
Front Driver side UNDER DASH

Feb 12, 2009 | 2000 Ford Windstar

1 Answer

2000 ford windstar, directionals both not working, hazards work f

turn signal flasher module or turn signal switch. I usuall try to wiggle teh column switch or move it slowly up and down, back and forth to help determine if it has a bad contact. if i cant get a failure (or turn signal) that way I begin the testing at the base of the column. the flasher module is a common failure on those and isnt unreasonably priced. if i had no diagnostic procedure i would try that first. oh yea, try turning the hazards on and off rapidly several times. the signal goes through the four way switch.

Dec 31, 2008 | 2000 Ford Windstar

2 Answers

Dashboard indicator light

what color is the light a red or yellow amber color or green.

Nov 30, 2008 | 1998 Honda Civic

1 Answer

Right Indicator light (Amber) is not working

Try installing a different bulb in that socket. Did you check voltage at the inner prongs where the bulb goes in or was it checked at the wiring. Check the condition of the socket that the bulb goes into. You may have to cut off the socket and replace it with a good one.

Jul 31, 2008 | 2000 Ford Windstar

Not finding what you are looking for?
2000 Ford Windstar Logo

Related Topics:

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers


Level 3 Expert

5581 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides