Question about 1990 Jeep Wrangler

1 Answer

I need the valve adjustment specs for a 1997 jeep wrangler four cylnder.thanks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

TIme to trade it in pal

Posted on Apr 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 jeep wrangler overheating


bought a used 97 jeep that apparently had the same problem and had a low temp thermostat installed in attempt to cure the problem. I noticed when draining the radiator that only 1/2 of fluid came out. I jumped up/down on bumper and dislodged sludge and other half of fluid. Flushed system twice and then noticed temp gauge was now registering low, out of specs. Placed in correct thermostat and all problems solved.

Dec 10, 2012 | 1997 Jeep Wrangler

1 Answer

How do i replace serpentine belt on 1997 jeep wrangler


Adjustment is made by loosening the power steering pump. There is a transverse long bolt (jack bolt) right under the pump that is used for adjustment.

Aug 02, 2010 | 1999 Jeep Wrangler

1 Answer

Hello i have a 1997 Jeep Wrangler 2.5L I will be


No just a standard socket set with regulation big hammer and a screwdriver kit will do

Jul 04, 2010 | 1997 Jeep Wrangler

1 Answer

Engine diagram 1997 jeep wrangler SE


So how do you know you need one if you dont know where it is?? Oil pumps rarely go bad unless the engine is sludged from lack of maintenence. After you take the oil pan off, its there hanging down. Make sure you clean or replace the pick up tube. I'm sure you can google up torque specs, for the bolts. Usually there is major engine damage by the time you figure out that there is lack of oil pressure. I would get a professionals opinion before you waste time and money replaicing the oil pump. If the engine has any unusual noise or knocking, its too late.

Apr 23, 2010 | 1997 Jeep Wrangler

1 Answer

1997 Jeep Wrangler 4wd high disengages


you might try checking the linkage on trans case shifter. may need adjusting. might not be getting fully engaged

Feb 06, 2010 | 1997 Jeep Wrangler

1 Answer

Instructions for replacing 1997 Jeep Wrangler 6cyl


Its an easy job! Disconnect the battery first! That's very importand! Then disconnect the wiring pack from the ECU. Some models are equipt with snap-systems, other with a screw-system to remove the wiring connector from the ECU. If done, there are three or four screws that hold the ECU in place with the body. Remove the screws and you hold the ECU in your hands. To buy a new or rebuilt ECU, reffer to the numbers shown on the label at your Wranglers ECU in combination with the V.I.N. To connect the new ECU with the wiring pack, be careful with the connector! You need to put him in the right position to connect with the ECU. Do it slow and make sure the connector fits to all points. Otherwise you'll bake some contacts inside the connector.

Oct 23, 2009 | 1997 Jeep Wrangler

1 Answer

Torque spec for ring and pinion gear (RING BOLTS) 1997 wrangler TJ


Ring Gear Bolts

Models 181, 186 & 194 Axle 70-90 (95-122)
Model 198 Axle 95-105 (129-142)
Models 216 & 226 Axle 80 (108)
8 1/4" Ring Gear (Cherokee) 70 (95)

Oct 12, 2009 | 1997 Jeep Wrangler

2 Answers

I need to bleed the clutch on my 1992 jeep wrangler and need to know were to locate the bleeder insert


The bleeder valve will be on the slave cylinder. Follow the hydraulic line from the Master Clutch cylinder down to the slave cylinder by the transmission.

Oct 04, 2009 | 1992 Jeep Wrangler

1 Answer

Jeep 1997 Wrangler. Gear shifting very hard


synchronizers are going bad a used trans would be cheaper than a rebuild due to the labor involved

Aug 19, 2009 | 1997 Jeep Wrangler

1 Answer

Describe your 1997 Jeep Wrangler 1997 jeep wrangler 4 cyl idle fluctuates 900 rpm to 400 rpm after warmup no service engine light but check guages light comes on momentarily when rpm gets low and oil press...


The check gauges light is normal because at 400 rpm it isn't running fast enough to build sufficient oil pressure. I am guessing maybe a vaccum leak???

Jul 10, 2009 | 1997 Jeep Wrangler

Not finding what you are looking for?
1990 Jeep Wrangler Logo

Related Topics:

371 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...