Question about 1991 Isuzu Pickup

1 Answer

We have a problem startin the truck.We put in a new starter but still have to push start it? What else could be wrong?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Replace your positive cable from the battery to the starter it is most likely the problem.

Posted on Mar 20, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1993nissanpickup d21try startin but just click new battery

check your ignition switch solinoid, it could be shot or check your starter relays and fuses, check the theft prevention switch just under the ignition cylinder. there are multiple things that could be causing this problem, but if your like me, you can just bypass all the starting relays for the starter and run a switch inside the cab to push that runs directly from the battery to the starter, and install a push-start button on the dash. let me know if this has helped you any, good luck.

Razer Neil

Jul 11, 2014 | 1993 Nissan Pickup

1 Answer

1991 toyota corolla clicking starter while start it

Starter gets jammed after fitting and to confirm the same, engage your car in second gear and try pushing front and back and it should release. Try starting thereafter. In most cases it works.

Apr 07, 2012 | Cars & Trucks

1 Answer

I have a 2000 chevy blazer 2 door an the other day i went to drive out of the sub division an it flat out died pushed it back home an its wont start i jus put a new alltinator on it an i jus put a new fuel...

It might be the battery, plugs anything. Just so u don't end up spending a lot more n changing so many other things, do what u should have in the beginning. Its an OB2, run a scan on that vehicle. That will atz least give u a sense of direction on what to do next. Guessing might just cost you a lot more than u should spend.

Sep 07, 2011 | 2000 Chevrolet Blazer

1 Answer

Doesn't want to keep running and some grinding noise when startin

From what you describe I would suspect that the starter is not fully engaging. I'm assuming that the grinding noise you hear when you try to engage the starter is INSTEAD of the engine cranking. If I assumed wrong, ignore the following:
Pull the starter, check the flywheel for excessively worn areas. Most of the time the flywheel is ok, it's just the starter. Any time you disassemble a starter you should replace the bushings and brushes. Never remove the starter with the battery still connected. Remove the negative terminal from the battery before you attempt to remove the starter.

Jun 06, 2010 | 1986 Jeep Cherokee

1 Answer

I changed the starter in my 93 saturn before i

You left off or broke one of the feed wires that are hooked directly to the battery terminal on the starter.Good Luck!

Mar 21, 2010 | 1993 Saturn SL2

3 Answers

Is push starting and jump starting the same thing? i have a 96 ford ranger 4.0. i had a problem with my truck startin i changed the solenoid on the fender it started a few times then that was it. the only...

No push starting is not the same as jump starting.Jumpstarting is done buy using another vehicle or battery like a jumper pack to give it power.It sounds like you will need to change the starter it's self.It most likely has what they call a dead spot in it and either needs to be rebuilt or replaced.

Jan 31, 2010 | 1996 Ford Ranger SuperCab

1 Answer


check your connections. turn the key to the on position and leave it sit for a minute or so then turn it off and try again. could be a security key issue. try a different key if you have one. you could also have a bad starter if none of this helps

Nov 17, 2009 | 2002 Jaguar X-Type

1 Answer

Had a new starter motor fitted on 15/4/09 been workin ok till this morning 19/04/09 turned car of no wont start at all rac got it running but it still not startin have 2 bump start it now any idea what...

sounds like alternator can you test it on the vehicle ? if so take voltmeter put probe to the battery post on back of alternator. and your ground ( black ) probe to a good ground. you should have at very least 12.35 volts that is the minimum. it could be showing 14-16 volts thats good but once again if it is below 12.35 replace the alternator

hope2help shack

Apr 19, 2009 | 2002 Jaguar X-Type

Not finding what you are looking for?
1991 Isuzu Pickup Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14411 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides