Question about 2001 Daewoo Lanos

1 Answer

The front left wheel bearing is shot and I can not get it out of the hub. Do I need to take the whole hub off to get it out? Also do I need any other parts than the bearing itself? Daniel

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

You need to take the slip rings out from the front and back side and then you can remover the bearings and their sleeves.

Posted on Aug 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace front right wheel bearing


Front wheel drive?if so which i think it is you need to remove the whole hub assy then use a universal hub seperator to remove the bearing then press a new bearing in. some vehicles such as ford festiva need a special tool to adjust a shim thickness which is imperative. I would sugest you get a 2nd hand hub assy with a good bearing in it & just replace the whole assy :-)

Oct 12, 2012 | 2000 Ford Windstar

4 Answers

I have a loud humming sound coming from what sounds like the front right wheel. I jacked it up and checked the wheel for play. and there is no movement. but the humming is getting worse. its not the...


Unfortunately you do not always get "play" in the bearing and they are unserviceable. Replace the entire unit. Here are the instructions for replacement. They bolt into place making it pretty easy to do. Soak the CV shaft which pertrudes from the hub where the nut goes with a good rust penetrant to ease in removal.


Removal & Installation


  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Front wheel Wheel Speed Sensor (WSS) electrical connector Brake caliper and bracket Rotor Driveshaft nut
  3. Install a front hub removal tool to the wheel bearing/hub assembly with three wheel nuts. Use the tool to push the driveshaft out of the wheel bearing/hub.
  4. Remove the wheel bearing/hub assembly and discard the bolts.

To install:
  1. Install or connect the following:

    Wheel bearing/hub assembly using new bolts and torque them to 96 ft. lbs. (130 Nm) New drive shaft nut and torque it to 118 ft. lbs. (160 Nm) Brake rotor Front caliper with the bracket WSS electrical connector Front wheel

May 16, 2011 | 2003 Chevrolet Impala

1 Answer

Bearing on front wheel


What about it? Most people question if you can just replace the bearing, or do you need to replace the whole hub assembly. Unfortunately, need to replace the whole wheel bearing hub assembly.

Dec 16, 2010 | 2004 Chevrolet TrailBlazer

1 Answer

Is it better to change the whole wheel bearing hub if the wheel bearings are shot on a 1998 Ford aspire ?


I cant say it is better but much easier to do it that way if you dont have proper tools to pull the bearing off of the old hub

Oct 02, 2010 | 1997 Ford Aspire

1 Answer

2004 silverado 4x4 2500 left front wheel bearing


  1. Raise and support the vehicle.
  2. Remove or disconnect the following:

    Tire and wheel assembly Caliper and rotor Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle Electrical connection for the wheel speed sensor Front drive halfshaft assembly on four wheel drive models Hub and bearing assembly mounting bolts Hub and bearing assembly O-ring seal from the steering knuckle bore (2500 series)
  3. Clean and inspect the O-ring seal
To install:
  1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly.
  2. Install the O-ring to the steering knuckle (2500 series).
  3. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent.
  4. Install or connect the following:

    Hub and bearing assembly Hub and bearing assembly mounting bolts. Tighten the bolts to 133 ft. lbs. (180 Nm). Front drive halfshaft assembly on four wheel drive models Electrical connection for the wheel speed sensor Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle. Tighten to 106 inch lbs. (12 Nm). Rotor Tire and wheel assembly.
You can go to autozone.com and register for free online repair manual with everything you need.

Jan 19, 2010 | 2004 Chevrolet Silverado 2500 Crew Cab

1 Answer

Sheered off stud. Easily replaced or whole new wheel hub assy?


Should be able to have the peice of stud that is left in the tire taken out and a new stud pressed in!!

Sep 24, 2009 | 2006 Chevrolet Uplander

3 Answers

I Think I have a front wheel bearing problem


Check wheel bering for play if there is no play , it doesn't mean that bearing is NOT bad its can still be dry and would be making that grinding sound you described Also check axle and see if boot is broken. That may be your problem also make sure that rotors are not gouged/scraped up and pads are good.Contact if you need more help and thanks for using FIX YA

May 05, 2009 | 2004 Kia Sedona

3 Answers

ABS error code 41 & 42


41 indicates Rpm sensor, at left front wheel, 42, is right front sensor. I'd check for dirt in and around both, clean connections, and wire brush or whatever the toothed ring to clean it all up, then clear codes & see what happens.

Apr 04, 2009 | 1993 Chevrolet K1500

Not finding what you are looking for?
2001 Daewoo Lanos Logo

Related Topics:

164 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

yadayada
yadayada

Level 3 Expert

60541 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...