Question about Honda Odyssey

1 Answer

INTERIOR REARVIEW MIRROR FELL OFF - Odyssey Honda Cars & Trucks

Posted by on

  • Anonymous Apr 17, 2009

    The Honda CR-V mirror is not attached to the window, so this solution doesn't work on a CR-V.  The mirror is attached via a screw assembly to the roof of the CR-V.  How can the CR-V mirror be re-attached?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 163 Answers

Just about all auto parts stores carry a little kit that includes slovent and glue to replace the metal "nub" onto the glass. There is a screw on the mirror that attaches the mirror to this "nub". Do not use force to remove the old glue or nub, windshield will crack.

Posted on Jul 27, 2008

4 Suggested Answers

  • 208 Answers

SOURCE: INTERIOR REARVIEW MIRROR FELL OFF

they sell repair manuals all day long at your local parts store:)

Posted on Jun 22, 2009

alicantecoli
  • 21949 Answers

SOURCE: how do u seperate the metal plate from the rearview mirror

use a special pad if you can get one or a new mirror ,do not glue it with epoxy type glues because the sun will expand it and then the windscreen will crack ,trust me ,got the teashirt here

Posted on Nov 22, 2009

  • 691 Answers

SOURCE: rearview mirror fell off. how

It may be held on by small set screw. (Allen wrench type) Or it just pops on and off, with effort.
To pop it off, hold the mirror as it would normally sit, and with that position in mind, you want to slide the metal plate down and out of the mirror clip, and you may have to pry on it a bit to get it started.

After you have reattached the plate to the windshield, you will have to apply almost the same force to clip the mirror back on.

Tips: Mark the location of the metal plate with a piece of tape on the outside of the windshield.
Make sure you clean the old glue off both the plate and windshield. Do not scratch metal plate.
Make sure you glue the plate on correctly. Do a trial fit on the mirror just prior to glueing.

Posted on Aug 28, 2011

  • 56 Answers

SOURCE: change interior light bulb

If this is the light that is controlled with the center switch, it can easily be changed by carefully prying the plastic cover off and replacing the bulb, found at any local auto parts store.

Posted on Dec 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My rearview mirror fell off and im having problems putting it back on without the metal button/bracket/mount that suppose to be there.


when your mirror fell off the metal bracket stood with the mirror
unscrew it
there a special glue for fix it on windshield

Oct 06, 2013 | 2002 Buick Regal

1 Answer

I have a 2000 buick regal. the rearview mirror fell down. How do i get the metal piece out to reattach to the windshield?


should just be a torx 15 also t15 screw driver to unscrew it and u must use the rearview mirror adhesive sold at most parts stores

Jun 12, 2011 | 2000 Buick Regal

1 Answer

How do u seperate the metal plate from the rearview mirror


use a special pad if you can get one or a new mirror ,do not glue it with epoxy type glues because the sun will expand it and then the windscreen will crack ,trust me ,got the teashirt here

Nov 22, 2009 | 2002 Kia Optima

1 Answer

Hot to install driver's side rearview mirror '98 Expedition


3 10mm nuts located behind the interior door panel (directly behind the mirror assembly) attach the mirror to the door. Also there you will find the point of attachment for the power as well.

Oct 01, 2009 | 1998 Ford Expedition

2 Answers

How do you reattach the rearview mirror on a 2001 tacoma Thanks


get a rearview mirror glue kit and follow the instructions.

Aug 02, 2009 | 2001 Toyota Tacoma

1 Answer

Cavalier convertible rearview mirror fell off


there is a screw that holds that piece of metal in place. take the screw out and remove the piece of metal then look at a local hardware or automotive store and ask for the windshield adhesive. and fallow that instructions pay close attention to the temperature to be applied at and the Harding or drying time.

Oct 11, 2008 | 1996 Chevrolet Cavalier

1 Answer

Custom Rear view mirror


Hiya...ALL factory-installed rearview mirrors are installed with different wires due to options.
About 6 different rearview mirrors are installed with those options such as On-Star, light, compass, and those features which use different wires....THIS CANNOT be modified with different rearview mirror....**for example, the Equinox owner attempt to pull out a factory-installed base rearview mirror and put in different one that has compass/temperature built into the rearview mirror**

However, the wires are located inside the front headliner which requires removing the sunvisor (and possible removal of interior plastic trim part at the left/right ends of the windshield) prior to pull the headliner down, and a small metal philips or torx screw is used to secure the rearview mirror onto the bracket glued to the windshield.

The best solution is to leave the original factory-installed rearview mirror in place.

May 16, 2008 | 2006 Chevrolet Equinox

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...