Question about 1995 Honda Civic del sol

Open Question

Vacuum hoses i put a skunk2 intake manifold in my delsol but i got ahead of myself and didnt label the hoses every thing is on but there a hoses that suppose to go the the throttle body whats the throttle body suppose connect to? the intake or the intake manifold?

Posted by on

6 Suggested Answers

inf12
  • 13 Answers

SOURCE: intake manifold vacuum line

THIS IS FOR TURBO ENGINE
13b2405.jpg NON TURBO ENGINE
6781864.jpg

Posted on Feb 08, 2009


SOURCE: Oil in the intake manifold air hose...

This is usually an indication of "blowback" caused by worn piston rings. How many miles on the engine? There is not a cheap solution if it is blowback.

Posted on Apr 28, 2009

  • 420 Answers

SOURCE: hyundai coupe intake manifold gasket

No this is not the manifold gasket. It is most likely a bad O2 sensor.

Posted on Jun 22, 2009

j_del
  • 1586 Answers

SOURCE: 92 Honda civic LX hessitation.

Did you have the computer reflashed for the new injectors? If not, you have to do so. I don't know how much bigger than stock your new fuel injectors are but if it's more than just a little bigger, and you don't reprogram the computer, your mixture is going to be way too rich and you'll be stumbling. Have the ECU reprogrammed to properly control the injectors - many modifications don't affect, or are not affected by, the ECU, but injectors aren't on that list. If you did reprogram it, it may be simply because larger injectors aren't as precise when flowing slowly or at small duty cycles. There's also the chance that one or more are leaking slightly although that's not as common.

Posted on Jan 22, 2010

bluebirdmate
  • 1190 Answers

SOURCE: The plenum boot between the intake manifold and

Hello, You have to remove the intake manifold.

Posted on Sep 04, 2010

  • 4331 Answers

SOURCE: '06 chevy aveo vacuum leak at the intake manifold.

Proper resealing and problem resolution (warpage, etc.) cannot be done without removing and inspecting...
TPI sensors are problems on many cars, not a huge deal....

Posted on Sep 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fine the engine vacuum reference tube for the fpr on a 1988 ranger 2.9 L v6 Fuel injection


It will be an intake manifold vacuum tap. Check all the taps from the intake manifold. The fpr hose may be teed off from another hose to another device. Just trace them all down, and you should find it. There would be a vacuum diagram scheme on the emissions label under the hood- see if it is still legible.

Aug 16, 2014 | Cars & Trucks

1 Answer

How to remove air from cooling system 1999 nissan maxima


Remove the negative battery cable from your Nissan Maxima. Wait at least 10 minutes in order to prevent the engine cooling fan from causing any potential harm while your hands are near it. Additionally, the engine must be completely cool in order to safely remove the air intake manifold.

Use a screwdriver to remove the hose clamps around the air intake duct. Gently pull the duct from the rest of the manifold.

Disconnect the accelerator cable, cruise control cable, hoses and electrical connections from the throttle body. Coolant may be lost through some of the hoses, which can be prevented by utilizing hose clamps or plugs. Be prepared with a catch pan underneath the hoses to collect any major spills.

Disconnect the spark plug wires from both the spark plugs and the retainers on the plenum. Unbolt the distributor cap. Use a pen and tape to label each wire with its location so that you can easily return each wire to its exact location once the air intake manifold has been put back in place.

Disconnect the ground strap, which is attached to the upper plenum of the air intake manifold and use a socket wrench to loosen the bolts. There are 11 bolts on the upper intake plenum.

Remove the upper plenum, which should still be attached to the throttle body. While the upper plenum of the Maxima's intake manifold is removed, it is a good idea to clean the mounting surfaces as well as the inside of the manifold with a stiff wire and brake cleaner. Use lint-free mechanics' rags to wipe away carbon buildup.
Removing the Lower Plenum

Drain the cooling system by inserting a catch pan beneath the radiator's drain bolt. Unscrew the drain bolt and hold up a 3/8 hose with a funnel on the end of it to direct the coolant to the catch pan. Open the drain fitting with a pair of pliers and remove the radiator cap.

Remove the radiator hose from the thermostat housing and disconnect the electrical connections from the coolant temperature switch and the coolant temperature sensor. Label these connections with tape and pen as described above for the upper plenum hoses and wires.

Remove the bolts to disconnect the coolant pipes at the transmission's end of the intake manifold.

Loosen the bolts on the lower manifold by turning them in 1/4-turn increments until they can be removed by hand. The manifold may need some gentle nudging to be released from the cylinder heads, but do not pry it loose -- doing so can cause damage to the sealing surfaces, leading to vacuum leaks.

Use a scraper to remove any gasket material and sealant from the outer parts of the manifold and cylinder heads. Clean the mating surfaces with lacquer thinner or acetone so that a new gasket can be applied to the lower manifold.

Jul 08, 2012 | 1999 Nissan Maxima

1 Answer

Replace no 3 coil


if im not mistaken the number 3 coil is on the right hand side of the motor so you will need to remove the intake manifold to gain access to it.
Intake Manifold Removal
  1. Remove the engine cover (if equipped).
  2. Remove the air filter outlet pipe.
  3. Remove the positive crankcase ventilation hose.
  4. Remove the air cleaner resonator.
  5. Disconnect the throttle body electrical connectors.
  6. Disconnect the electrical connectors.
  7. Detach the vacuum hoses.
    • Press the retaining ring. (1)
    • Detach the vacuum hose. (2)

  8. Disconnect the vacuum hose.
  9. Detach the injector harness electrical connector from the intake manifold support bracket.
  10. Remove the intake manifold support bracket.
  11. Detach the engine wiring harness bracket.
  12. Detach the intake manifold support bracket.

    NOTE: Remove and discard the O-ring seal.
  13. Detach the throttle body.
    • Remove the retaining bolts.
  14. Remove the intake manifold.
    • Remove and discard the intake manifold gaskets.

Apr 22, 2012 | 2003 Jaguar X-Type

1 Answer

I need written instructions for installing an EGR Valve on a 96 Ford Exploer Eddie Bauer V6 4.0 engine. Trying to pass emission inspection.


zjlimited_986.jpg

Fig. 4: Exploded view of the EGR system and related components for the 4.0L engine (click over pic for zoom)

REMOVAL & INSTALLATION

PFE/DPFE Sensor
This component is found on all engines, and is also referred to as the backpressure transducer.
  1. Disconnect the negative battery cable.
  2. Detach and label the wiring harness connector from the PFE/DPFE sensor.
  3. Disconnect all of the hoses from the sensor.
  4. Remove the mounting nuts, then separate the sensor from the mounting bracket.
  5. If necessary, remove the EVR solenoid and the PFE/DPFE mounting bracket from the upper intake manifold.
To install:
  1. If removed, install the EVR solenoid and mounting bracket onto the upper intake manifold.
  2. If applicable, install the EGR tube heat shield.
  3. Position the PFE/DPFE sensor on the mounting bracket, then install and tighten the mounting nuts until snug.
  4. Attach all necessary hoses and wiring to the sensor.
  5. Connect the negative battery cable.

EGR Vacuum Regulator (EVR) Solenoid
The EVR solenoid is mounted either on the same bracket as the PFE/DPFE sensor, attached to the upper intake manifold, or near the EGR valve on its own bracket.
  1. Disconnect the negative battery cable.
  2. Label and detach the wiring harness connector from the EVR solenoid.
  3. Detach the main emission vacuum control connector from the solenoid.
  4. Remove the retaining nuts, then separate the solenoid from the mounting bracket.
To install:
  1. Position the solenoid on its mounting bracket and install the retaining nuts.
  2. Attach the main emission vacuum control connector and the wiring harness connector to the EVR solenoid.
  3. Connect the negative battery cable.

EGR Valve
See Figures 6 and 7
  1. Disconnect the negative battery cable.
  2. If necessary, remove the air inlet tube from the throttle body and air cleaner housing.
  3. Label and detach all vacuum hoses from the EGR valve.
  4. Label and detach any electrical wiring harness connectors from the EGR valve.
  5. Disconnect the EGR valve-to-exhaust manifold tube from the EGR valve.
  6. Remove the EGR valve mounting fasteners, then separate the valve from the upper intake manifold.
  7. Remove and discard the old EGR valve gasket, and clean the gasket mating surfaces on the valve and the intake manifold.
zjlimited_987.jpg

Fig. 6: Cutaway view of a base entry type EGR valve

zjlimited_988.jpg

Fig. 7: Cutaway view of a side entry type EGR valve

To install:

  1. Install the EGR valve, along with a new gasket, on the upper intake manifold, then install and tighten the mounting bolts to 4-22 ft. lbs. (20-30 Nm) on 3.8L engines, or to 106-49 inch lbs. (1-18 Nm) on 5.0L engines.
  2. Connect the EGR valve-to-exhaust manifold tube to the valve, then tighten the tube nut to 30 ft. lbs. (41 Nm).
  3. Connect all wiring or hoses to the EGR valve.
  4. Install the air inlet tube.
  5. Connect the negative battery cable.


Hope this helps, good luck (remember to rate this comments).

Apr 06, 2011 | Ford Explorer Cars & Trucks

1 Answer

I need to replace the hose that runs from the bottom of the engine to the intake


Do you mean the oil drain hose that goes from the flame arrestor up by the intake manifold down to the oil mist eliminator on the driver side of the engine block?
That hose is a bit of a PITA to replace, especially if this is a California car with an EGR.
If I were doing it, I would go ahead and make a day of it, pulling off the intake manifold, removing the oil mist eliminator and cleaning it out, and cleaning out all the vacuum ports on the manifold, and cleaning out the EGR piping (if applicable). That way you end up with everything flowing as it should and a nice fresh intake manifold gasket. I suspect you will find that the car runs better when you are done.

Feb 28, 2011 | 1991 Volvo 740

1 Answer

How to replace an intake manifold gasket on a 1996 gmc jimmy


Hello,

Here is a detailed summary on the procedure of how to replace the intake manifold gasket on a 1996 gmc jimmy;
REMOVING THE UPPER INTAKE MANIFOLD(PLENUM)
STEP 1 Disconnect Battery (may not be absolutely necessary, but a good practice to avoid shorting a positive wire to ground).


STEP 2 Remove serpentine belt.

STEP 3 Drain the coolant.

STEP 4 Remove air cleaner ducting and disconnect wires.

STEP 5 Disconnect throttle linkage and bracket.

STEP 6 Disconnect cruise control cable.

STEP 7 Remove brake booster vacuum hose at manifold.

STEP 8 Remove PCV hose.

STEP 9 Remove ignition coil and bracket.

STEP 1O Remove purge solenoid and bracket.

STEP 11 Relieve fuel pressure at test port.

STEP 12 Remove fuel lines and bracket.

STEP 13 Remove upper intake manifold.

REMOVING THE LOWER INTAKE MANIFOLD
STEP 1 Remove the distributor and label the spark plug wires.

STEP 2 Remove heater hoses and bypass hose.

STEP 3 Remove upper radiator hose.


STEP 4 Remove EGR valve?

STEP 5 Remove sensors and bracket on right side.

STEP 6 Remove EGR tube, clamp and bolt.

STEP 7 Remove PCV valve (and replace).

STEP 8 Unbolt A/C compressor and move it aside.

STEP 9 Loosen compressor bracket and slide forward, but do not remove it.

STEP 10 Remove alternator bracket bolt (or remove alternator and set aside)

STEP 11 Unplug all vacuum lines from intake manifold.


STEP 12 Unplug all electrical connectors from manifold.

STEP 13 Take note of the intake manifold bolts and mark the location of the bolts.


STEP 14 Remove intake manifold bolts, and manifold.

STEP 15 Clean mating surfaces

THE MAIN INSTALLATION
STEP1 Set the new gaskets in place and apply silicone to flat areas on front and rear of engine block.

STEP2 Apply thread locking compound to manifold bolts.

STEP 3 Install the manifold and tighten bolts to 35 ft-lbs, in proper sequence.

STEP4 Install the distributor.

STEP5 Install the upper intake manifold.



The remaining installation procedures are basically the reverse of removal.


Have a nice day.

Dec 04, 2010 | 1996 GMC Jimmy

2 Answers

Cylinderhead torque stc.


Cylinder Head Removal & Installation SOHC To Remove:
  1. Relieve fuel system pressure.
  2. Remove timing belt cover. Camshaft timing marks kia-03-20-7032.gif

  3. Turn crankshaft until timing mark on front housing and the arrow "2" on the camshaft pulley align.
  4. Loosen lock bolt on tensioner.
  5. Pry tensioner away from timing belt and tighten lock bolt to relieve tension on the timing belt.
  6. Remove timing belt from camshaft pulley.
  7. Disconnect battery negative cable.
  8. Remove 3 bolts that secure accelerator cable and air intake hose to cylinder head cover.
  9. Detach accelerator cable and place off to side.
  10. Remove the following;
    • Air hose
    • Air ISC air hose
    • Breather hose
    • Vacuum hose from air intake hose
  11. Disconnect mass air flow sensor electrical connector.
  12. Remove air intake hose.
  13. Remove PCV valve from cylinder head cover.
  14. Remove ISC air hose from idle speed actuator.
  15. Remove air hose from behind intake manifold.
  16. Remove 2 screws from high tension wire protectors.
  17. Detach wire loom from holder at rear of cylinder head cover.
  18. Detach vacuum tube at rear of cylinder head cover.
  19. Remove vacuum pipe. Cylinder Head Cover kia-03-20-7042.gif

  20. Remove 7 cylinder head cover bolts.
  21. Remove cylinder head cover and gasket.
  22. Disconnect 2 ignition coil electrical connectors.
  23. Disconnect 2 fuel injection electrical connectors at rear of cylinder head.
  24. Disconnect the following electrical connectors;
    • Oxygen sensor
    • Throttle position sensor
    • Idle speed actuator
    • Oil pressure switch
    • EGR vacuum solenoid valve at intake manifold
  25. Disconnect heater hose from elbow.
  26. Disconnect brake booster vacuum hose and cruise control vacuum hose from surge tank.
  27. Detach wire harness from rear of cylinder head.
  28. Disconnect purge control solenoid vacuum hose from intake manifold.
  29. Disconnect fuel hose from fuel connector assembly.
  30. Remove grounding bracket.
  31. Remove 4 bolts and intake manifold bracket.
  32. Remove starter.
  33. Detach water bypass hose from bypass pipe.
  34. Disconnect water hoses from oil cooler.
  35. Disconnect fuel hose from fuel pipe.
  36. Remove exhaust manifold heat shield.
  37. Remove exhaust flange nuts and front exhaust bracket bolt.
  38. Lower exhaust system. Cylinder head bolt loosening sequence kia-03-20-7050.gif

  39. Loosen cylinder head bolts in 3 steps in proper sequence.
  40. Remove cylinder head bolts and washers.
  41. Remove cylinder head, intake manifold and exhaust manifold as an assembly.
To Install:
  1. Install NEW cylinder head gasket.
  2. Install cylinder head, intake manifold and exhaust manifold as an assembly.
  3. Tighten cylinder head bolts in 3 steps in reverse sequence that was used during removal. Tighten bolts to 62 ft lb (84 Nm).
  4. Install front exhaust bracket bolt. Tighten bolt to 20 ft lb (27 Nm).
  5. Install NEW lower exhaust flange gasket and 3 nuts. Tighten nuts to 24 ft lb (31 Nm).
  6. Install exhaust manifold heat shield. Tighten nuts to 35 in lb (4 Nm).
  7. Connect fuel hose to pipe.
  8. Connect 2 hoses to oil cooler.
  9. Attach water bypass hose to bypass pipe.
  10. Install starter and bolts. Tighten bolts to 34 ft lb (46 Nm).
  11. Install intake manifolds bracket and 4 bolts. Tighten bolts to 32 ft lb (45 Nm).
  12. Install grounding bracket.
  13. Connect fuel hose to fuel connector assembly.
  14. Connect the following electrical connectors;
    • Oxygen sensor
    • Throttle position sensor
    • Idle speed actuator
    • Oil pressure switch
    • EGR vacuum solenoid valve at intake manifold
  15. Connect purge control solenoid vacuum hose to intake manifold.
  16. Attach wire harness from rear of cylinder head.
  17. Connect brake booster vacuum hose and cruise control vacuum hose to surge tank.
  18. Connect heater hose to elbow.
  19. Connect 2 fuel injection electrical connectors at rear of cylinder head.
  20. Connect 2 ignition coil electrical connectors.
  21. Install cylinder head cover.
  22. Install 7 cylinder head cover bolts. Tighten bolts to 60 in lb (7 Nm).
  23. Install vacuum pipe and 2 bolts at rear of cylinder head cover. Tighten bolts to 60 in lb (7 Nm).
  24. Connect vacuum tube to pipe.
  25. Connect loom holder to rear of cylinder head cover.
  26. Install 2 screws to high tension wire protectors.
  27. Install air hose to behind intake manifold.
  28. Install ISC air hose to idle speed actuator.
  29. Install PCV valve to cylinder head cover.
  30. Install air intake hose.
  31. Connect mass air flow sensor electrical connector.
  32. Install the following;
    • Air hose
    • Air ISC air hose
    • Breather hose
    • Vacuum hose from air intake hose
  33. Attach accelerator cable.
  34. Install 3 bolts that secure accelerator cable and air intake hose to cylinder head cover. Timing belt pulley timing marks kia-03-20-7035.gif

    NOTE: Timing belt pulley timing mark and timing mark must be aligned.
    Camshaft timing marks kia-03-20-7032.gif

    NOTE: The arrow at "2" on camshaft pulley must be aligned with timing mark on front housing.
  35. Install timing belt.
  36. Install timing belt cover.
  37. Pressurize fuel system.
  38. Start engine and check ignition timing.

Jul 11, 2010 | 1999 Kia Sportage

2 Answers

Power steering loses fluid, no obvious leak found, a shop replaced the high pressure hose but didnt solve the problem, they said the hose "was leaking". Problem has not changed since they replace the hose-...


If the hose did not solve the problem, take it back. Tell the service manager ou came in to have the disappearing oil problem corrected, you didn't come in to replace a hose on a hit or miss repair. Sweiously, That is alot of money for a hose replace.

Jan 26, 2010 | 1992 Toyota 4Runner

1 Answer

Intake manifold gasket


prev.gif next.gif Intake Manifold REMOVAL & INSTALLATION 1.9L SOHC Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Properly relieve the fuel system pressure.
  3. Drain the coolant system.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Air cleaner fresh air hose
    • Positive Crankcase Ventilation (PCV) valve hose
    • Fuel line from the rail
    • Throttle cable from the throttle body
    • Throttle cable bracket nuts
    • Fuel injector electrical connectors
    • Throttle Position (TP) sensor electrical connectors
    • Idle Air Control (IAC) valve electrical connectors
    • Manifold Absolute Pressure (MAP) sensor electrical connectors
    • Exhaust Gas Recirculation (EGR) valve electrical connectors
    • Heater hose from the intake manifold outlet
  5. Position the wiring harness over the brake master cylinder
  6. Remove or disconnect the following:
    • Intake manifold support bracket bolt
    • Label the vacuum line for proper assembly
    • Drive belt
    • Power steering pump
    • Upper intake manifold bolts
    • Evaporative Emissions (EVAP) canister purge valve solenoid vacuum hose
    • Brake booster vacuum hose
    • Lower intake manifold bolts
    • Intake manifold
    To install:
  7. Thoroughly clean all gasket mating surfaces. Be careful not to damage or score the aluminum surface. If replaced, use Loctite® 290, to seal the new PCV valve inlet tube into the manifold. NOTE: Refer to Section 1 of this manual for the intake manifold torque sequence illustration. The illustration is located after the Torque Specification Chart.
  8. Install or connect the following:
    • New gasket and manifold. Torque the nuts in sequence to 22 ft. lbs. (30 Nm).
    • Power steering pump. Torque the fasteners to 27 ft. lbs. (38 Nm).
    • Drive belt.
    • Heater hose and install the manifold support bracket bolt. Tighten the bolt to 22 ft. lbs. (30 Nm).
    • Lubricate the male ends of the fuel lines with a few drops of clean engine oil, then connect the fuel supply and return lines.
    • Fuel line(s) in the retaining bracket. Torque the mounting screw to 36 inch lbs. (4 Nm).
    • Throttle cable to the throttle body and attach the accelerator cable bracket. Torque the bolts to 22 ft. lbs. (30 Nm).
    • Reposition the wiring harness and connect the wiring and vacuum hoses to their original locations. The harness leads to the TP sensor and EGR solenoid must be routed between the intake manifold runners.
    • Negative battery cable
  9. Fill the coolant system.
  10. Prime the fuel system by cycling the ignition ON for 5 seconds and OFF for 10 seconds a few times without cranking the engine.
  11. Start the engine, check for leaks, and repair if necessary.

Mar 27, 2009 | 2000 Saturn SL

1 Answer

Loud whining noise after the intake manifold was put back on


If its a sucking noise the intake is pulling air in somewhere. Try an old mechanics trick, get some wd-40 and crank the engine up then spray it along where the intake bolts to the block listen for any changes in the engine rpm. If you hear changes then the intake is pulling air.
Good luck and dont forget to rate.

Mar 23, 2009 | 2001 Mazda 626

Not finding what you are looking for?
1995 Honda Civic del sol Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...