Question about 1991 Jeep Wrangler

1 Answer

Can't transfer to 4L or neutral mode

I've been trying to transfer case from 2wd to 4wd. It shifts to 4L without any problem, but it doesn't move anywhere else. Can't figure out what might be a problem.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,498 Answers

Transfer cases can be quirky. I've got a 91 Wrangler, an 86 Cherokee and a 75 Blazer. When I go from 2WD to 4WD, they each have their own personality.

There are a number of things I've learned to persuade a stubborn xfer case to shift.

Try mixing these :

  • Engine running, vehicle not moving
  • Engine off, Shift Xfer case, Restart
  • Tranny in neutral
  • Shift Xfer case 'N', Tranny in gear, Tranny in neutral, Xfer case to 4HI or 4LOW (as long as you feel it register), Tranny in gear, try to move
  • Shift Tranny to Reverse, roll a few yards
  • Lock/Unlock the Hubs
To get back to 2WD:
  • Drive for a few feet in a straight line
  • Unlock the hubs
  • Tranny Neutral
  • Shift xfer case
Let me know how it turns out.
Mike

Posted on Aug 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I turn 4wd on?


    • 1 Start your Dodge truck's engine.
    • 2 Turn the electronic transfer case from "2WD" to "4WD Lock" to engage the high range 4WD, if the dodge truck is equipped with an electronic transfer case; otherwise, shift the transfer case lever from "2H" to "4H." The electronic transfer case is located on the instrument panel and is marked with "2WD," "4WD Lock" and 4WD Low." The lever-equipped transfer case is located to the right of your leg and is marked with "2H," "4H" and "4L."
    • 3 Shift the transmission into "Neutral" while the vehicle is either stopped or rolling at 2 to 3 mph to begin engaging in the low range 4WD. Turn the electronic transfer case to "4WD Low," if the Dodge truck is equipped with an electronic transfer case; otherwise, shift the transfer case lever from "2H" or "4H" to "4L."
    Tips & Warnings
    • Indicator lights will come on and alert you that your vehicle is in either the high or low range of 4WD.
    • Do not engage in the low range of 4WD drive if the transmission is in gear; you must shift to "Neutral" first.
    • Many Dodge trucks allow you to shift from 2-wheel drive to the high range of 4WD at up to 55 mph--consult your truck's manual to ensure that this is possible. Do not exceed 55 mph while engaged in the high range of 4WD. Do not exceed 25 mph while engaged in the low range of 4WD.
    • Do not engage in 4WD unless you are on slipper or rocky roads.

Sep 02, 2011 | 2005 Dodge Dakota

1 Answer

I can not get power to the motor to engage my front axle on my 4x4.


Power as in 12 V DC ? if yes, you are not in the correct area, the front axle is locked in and out of 4x4 mode with vacuum.

Operationally vacuum shifts the front axle between 2WD and 4WD mode. The GEM ( Generic Electronics Module ) applies ground to the solenoid needed for the mode selected on the switch ( for ESOF ) or when the transfer case shift lever is moved ( MSOF ).The contact plates in the transfer case signal the GEM that the transfer case is engaged, and the Vacuum solenoids need to be activated ( either 2WD to 4WD or 4WD to 2WD ).


Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
- If it turns it is a problem with the transfer case.
- If it doesn't it is a front axle engagement problem.

- If the front drive shaft does not turn :
•With the truck running ( with front wheel back on the ground ), switch from 2WD to 4WD and back again, the vacuum shift motor should move the lever on the front axle.
sscullys_200.jpg
Item #10 in this diagram
sscullys_10.gif
-- If the vacuum shift motor does not move:
1.Check for vacuum on the lines while shifting between modes. Pink vacuum line is 2WD mode, Light Blue vacuum line is 4WD.
2.Check the fuses for the 4WD system and the solenoids.
3.Check the vacuum lines from the vacuum shift motor to the solenoids on the firewall.
4.Check the vacuum lines from the solenoids to the vacuum reservoir box behind the battery.
5.Check the vacuum reservoir box for cracks.
6.Typical solution is the vacuum lines ( to the solenoids or to the vacuum shift motor ) are cracked or the vacuum shift motor has a cracked diaphragm and has water in it.
7.Could be the shift plate contacts in the transfer case are corroded / not making good contact, and not activating the solenoids.
sscullys_199.jpg

- If the front drive shaft turns:
For ESOF system
-- Check the fuses for the transfer case, engine compartment fuse panel, 17 & Cab fuse panel fuses 13 and 23 ( verify with owners manual, 97-97 & 99-03 MY can be slightly different on some items ).
-- Try hitting the transfer case with a dead blow hammer ( do not use a metal hammer, it can damage the transfer case ) to see if the transfer case shift motor is hung up .
-- Check the transfer case connector, to make sure the connector pins are clean and making good contact.
For MSOF systems
-- Check that the shift linkage on the transfer case is moving when the lever is moved from 2W to 4H and 4L.

Jul 30, 2011 | 2000 Ford F150 Flareside SuperCab

1 Answer

I have a 2002 ford f150 xlt fx4 4.6l engine. 2 door reg cab. i have a 4 wheel drive shift lever. the 4 wheel will only engage on rare occasion and only after pulling into 4 low then to 2 high then back...


For the 2002 MY ( this is in the 2006 Section, just want to call it out to others that might find the solution, this does not apply to the 2006 MY )

Operationally vacuum shifts the front axle between 2WD and 4WD mode. The GEM ( Generic Electronics Module ) applies ground to the solenoid needed for the mode selected on the switch ( for ESOF ) or when the transfer case shift lever is moved ( MSOF ).The contact plates in the transfer case signal the GEM that the transfer case is engaged, and the Vacuum solenoids need to be activated ( either 2WD to 4WD or 4WD to 2WD ).


Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
- If it turns it is a problem with the transfer case.
- If it doesn't it is a front axle engagement problem.

- If the front drive shaft does not turn :
•With the truck running ( with front wheel back on the ground ), switch from 2WD to 4WD and back again, the vacuum shift motor should move the lever on the front axle.
{ picture of shift motor }
-- If the vacuum shift motor does not move:
1.Check for vacuum on the lines while shifting between modes. Pink vacuum line is 2WD mode, Light Blue vacuum line is 4WD.
2.Check the fuses for the 4WD system and the solenoids.
3.Check the vacuum lines from the vacuum shift motor to the solenoids on the firewall.
4.Check the vacuum lines from the solenoids to the vacuum reservoir box behind the battery.
5.Check the vacuum reservoir box for cracks.
6.Typical solution is the vacuum lines ( to the solenoids or to the vacuum shift motor ) are cracked or the vacuum shift motor has a cracked diaphragm and has water in it.
7.Could be the shift plate contacts in the transfer case are corroded / not making good contact, and not activating the solenoids.
sscullys_148.jpg

- If the front drive shaft turns:
For MSOF systems
-- Check that the shift linkage on the transfer case is moving when the lever is moved from 2W to 4H and 4L.

I am going to take a SWAG that it is 1 of 2 places, both cases the front drive shaft is locking into place.

1. The front vacuum shift motor is not moving ( vacuum or vacuum line issue ).
2. The contact plates for the shift motor are not making contact and are not signalling the GEM that the transfer case state has been changed.

I'd start with the front axle off the ground test, and see which way to go, before you start repalcing items.

Mar 27, 2011 | 2006 Ford F-150

1 Answer

My 98 f150 was in 4WD Hi this morning when I started it. Selector switch is in 2WD position. 4WD Hi light is on, hubs (or front differential) is engaged and transfer case engage. (Feel front wheel hop...


If the switch was in the 2WD position and the transfer case was locked in a 4WD range, my 2 SWAGs would be bad switch or the connector to the shift motor is damaged / corroded or the fuse to the transfer case shift relay module is blown ( fuse # 17 ) / problem with the transfer case shift relay module.

This is without knowing if the truck was used in 4WD the night prior, and shifted out just before turning off. If this is the case, the shift motor might be stuck, and a few hits with a dead blow hammer to the transfer case might jar it free again ( do not use a metal hammer, it could damage the transfer case ).

The vacuum shift solenoids on the firewall are controlled by the GEM ( Generic Electronic Module ) which is grounding either the 2WD or 4WD solenoid, depending on the shift plate contacts in the transfer case. ( when in 4 or 4H, the contact switch plate signals the GEM, which in turn grounds the correct solenoid ).

Pulling the switch will not cause the transfer case to go back to a default position, the switch has a resistance level for each mode, and needs that value to operate the shift motor.

The resistance values for the switch between the 2 dark blue wires:
2WD - 4100 to 3700 ohms
4H - 1050 to 1150 ohms
4L - 380 to 340 ohms
- find the wire locations on the switch, mark them and remove the connector to test the resistance.

Just my opinion on the order :

1. Check the fuses for the shift motor
2. Try the old school shift method, back up ~ 50' put into park or neutral, and shift from 4WD to 2WD.
2.1. This is to see if the transfer case shift motor is bound up, and reversing might release it
3. Try hammering the transfer case with a dead blow hammer while someone shifts from 2WD to 4WD. You only need the key in the run position, if it happens quick enough after running the engine, the vacuum reservoir will still have enough vac to operate the solenoids. Don't chance running yourself over.
3.1. If this frees up the shift motor and the vacuum has bled off, you can try starting the truck and shifting into 4H then back to 2WD to get the front axle to disconnect or manually vacuum operate the front disconnect motor by applying vacuum to the pink vacuum line on the shift motor on the front axle.

Mar 05, 2011 | 1998 Ford F150 Regular Cab

1 Answer

HOW TO SHIFT TO 4 WHEEL DRIVE


Hi - Here is instruction how to do.

From N to 4H

Stop the vehicle completely, place the

transmission in "N" (Neutral) and depress

the brake pedal and the clutch pedal fully

(if equipped), then push in and turn the

switch to shift into "4H".

From 4H to 4H LOCK

You can operate the transfer switch either

when the vehicle is stopped or while the

vehicle is moving.

Position the front wheels straight ahead

and turn the switch to shift into "4H LOCK".

If the vehicle is moving, we recommend

that the speed be less than 100 km/h (60

mph) during this operation.

NOTE:

• When shifting between the transfer

switch position and the transfer gear

position is unmatched, all 4WD indicators

will blink and the buzzer will sound.

• If it is difficult to shift between "4H" and

"4H LOCK" while the vehicle is moving,

try accelerating and decelerating your

vehicle several times after turning the

transfer switch. Be sure to wait until traffic

conditions allow you to accelerate and

decelerate safety before using this procedure.

From 4H LOCK to 4L LOCK

Stop the vehicle completely, place the

transmission in "N" (Neutral) and depress

the brake pedal and the clutch pedal fully

(if equipped), then push in and turn the

switch to shift into "4L LOCK".

From 4L LOCK to 4H LOCK

Stop the vehicle completely, place the

transmission in "N" (Neutral) and depress

the brake pedal and the clutch pedal fully

(if equipped), then push in and turn the

switch to shift into "4H LOCK".

From 4H LOCK to 4H

You can operate the transfer switch either

when the vehicle is stopped or while the

vehicle is moving.

Position the front wheels straight ahead

and turn the switch to shift into "4H". If the

vehicle is moving, we recommend that the

speed be less than 100 km/h (60 mph) during

this operation.

NOTE:

• When shifting between the transfer

switch position and the transfer gear

position is unmatched, all 4WD indicators

will blink and the buzzer will sound.

• If it is difficult to shift between "4H" and

"4H LOCK" while the vehicle is moving,

try accelerating and decelerating your

vehicle several times after turning the

transfer switch. Be sure to wait until traffic

conditions allow you to accelerate and

decelerate safety before using this procedure.

From 4H to N

64J209

Stop the vehicle completely, place the

transmission in "N" (Neutral) and depress

the brake pedal and the clutch pedal fully

(if equipped), then push in and turn the

switch to the mark (1) at the left of the "N"
position, and hold the switch in this posi-

tion for 5 seconds until the "N" indicator

blinks, then turn the switch to the "N" position.

When you turn the transfer switch to the

"N" position, "N" indicator will come on with

the buzzer sound.

CAUTION

• Be sure to stop the vehicle completely

before operating the transfer

switch to shift between "N" and

"4H", or between "4H LOCK" and

"4L LOCK".

• Do not shift between "4H" and "4H

LOCK" unless the front wheels are

in the straight-ahead position and

we recommend that the vehicle

speed be less than 100 km/h (60

mph).

Do not operate the transfer switch

while tires are racing.

• Do not operate your vehicle in "4H

LOCK" or "4L LOCK" on dry, hard

surfaces.

(Continued)

CAUTION

(Continued)

• Do not operate the vehicle while a

4WD mode indicator is blinking

except when shifting between "4H"

and "4L LOCK".

If you operate the vehicle while a

4WD mode indicator is blinking, a

buzzer will sound and the transfer

will shift to "N" (Neutral) to prevent

transfer case damage.

In this case, use the following procedure.

1) Depress the clutch pedal fully (if

equipped) or shift the automatic

transmission gearshift lever to the

"N" position.

2) Turn the transfer switch to the

position previously selected.
3) Operate the transfer switch again.

Feb 01, 2011 | 2007 Suzuki Grand Vitara 4WD

1 Answer

KinlogworksI have A 2003 F-150 Super Crew. I have only used th4 wheel drive a few dozen times. about a mounth ago i switched it into 4 high and nothing happened. problem also in 4 low. any advise?


Operationally vacuum shifts the front axle between 2WD and 4WD mode. The GEM ( Generic Electronics Module ) applies ground to the solenoid needed for the mode selected on the switch ( for ESOF ) or when the transfer case shift lever is moved ( MSOF ). The contact plates in the transfer case signal the GEM that the transfer case is engaged, and the Vacuum solenoids need to be activated ( either 2WD to 4WD or 4WD to 2WD ).

Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
- If it turns it is a problem with the transfer case.
- If it doesn't it is a front axle engagement problem.

- If the front drive shaft does not turn :
•With the truck running ( with front wheel back on the ground ), switch from 2WD to 4WD and back again, the vacuum shift motor should move the lever on the front axle.
{ picture of shift motor }
-- If the vacuum shift motor does not move:
•Check for vacuum on the lines while shifting between modes. Pink vacuum line is 2WD mode, Light Blue vacuum line is 4WD.
•Check the fuses for the 4WD system and the solenoids.
•Check the vacuum lines from the vacuum shift motor to the solenoids on the firewall.
•Check the vacuum lines from the solenoids to the vacuum reservoir box behind the battery.
•Check the vacuum reservoir box for cracks.
•Typical solution is the vacuum lines ( to the solenoids or to the vacuum shift motor ) are cracked or the vacuum shift motor has a cracked diaphragm and has water in it.
•Could be the shift plate contacts in the transfer case are corroded / not making good contact, and not activating the solenoids.
{ Picture of Vacuum diagram )

- If the front drive shaft turns:
•For ESOF system
-- Check the fuses for the transfer case, engine compartment fuse panel, 17 & Cab fuse panel fuses 13 and 23 ( verify with owners manual, 97-97 & 99-03 MY can be slightly different on some items ).
-- Try hitting the transfer case with a dead blow hammer ( do not use a metal hammer, it can damage the transfer case ) to see if the transfer case shift motor is hung up .
-- Check the transfer case connector, to make sure the connector pins are clean and making good contact.
•For MSOF systems
-- Check that the shift linkage on the transfer case is moving when the lever is moved from 2W to 4H and 4L.

Jan 18, 2011 | 2003 Ford F150 Regular Cab

1 Answer

2003 F-150 regular cab automatic transmission and the 4WD will not engage.


Operationally vacuum shifts the front axle between 2WD and 4WD mode. The GEM ( Generic Electronics Module ) applies ground to the solenoid needed for the mode selected on the switch ( for ESOF ) or when the transfer case shift lever is moved ( MSOF ).The contact plates in the transfer case signal the GEM that the transfer case is engaged, and the Vacuum solenoids need to be activated ( either 2WD to 4WD or 4WD to 2WD ).


Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
- If it turns it is a problem with the transfer case.
- If it doesn't it is a front axle engagement problem.

- If the front drive shaft does not turn :
•With the truck running ( with front wheel back on the ground ), switch from 2WD to 4WD and back again, the vacuum shift motor should move the lever on the front axle.
{ picture of shift motor }
-- If the vacuum shift motor does not move:
•Check for vacuum on the lines while shifting between modes. Pink vacuum line is 2WD mode, Light Blue vacuum line is 4WD.
•Check the fuses for the 4WD system and the solenoids.
•Check the vacuum lines from the vacuum shift motor to the solenoids on the firewall.
•Check the vacuum lines from the solenoids to the vacuum reservoir box behind the battery.
•Check the vacuum reservoir box for cracks.
•Typical solution is the vacuum lines ( to the solenoids or to the vacuum shift motor ) are cracked or the vacuum shift motor has a cracked diaphragm and has water in it.
•Could be the shift plate contacts in the transfer case are corroded / not making good contact, and not activating the solenoids.
sscullys_111.jpg

- If the front drive shaft turns:
•For ESOF system
-- Check the fuses for the transfer case, engine compartment fuse panel, 17 & Cab fuse panel fuses 13 and 23 ( verify with owners manual, 97-97 & 99-03 MY can be slightly different on some items ).
-- Try hitting the transfer case with a dead blow hammer ( do not use a metal hammer, it can damage the transfer case ) to see if the transfer case shift motor is hung up .
-- Check the transfer case connector, to make sure the connector pins are clean and making good contact.
•For MSOF systems
-- Check that the shift linkage on the transfer case is moving when the lever is moved from 2W to 4H and 4L.

Jan 10, 2011 | 2003 Ford F150 Regular Cab

2 Answers

4wd does not work


Electronic Shift On the Fly (ESOF) Operation
The ESOF system is an electronic shift 4x4 system that allows the operator to choose between two different 4x4 modes as well as 2-wheel drive. The operator can switch between 2WD and 4WD HIGH mode at speed. To engage or disengage LOW Range, the vehicle speed must be less than 5 kph, the brake depressed, and the transmission must be in NEUTRAL.

The transfer case is equipped with an electromagnetic clutch which is located inside the case. This clutch is used to spin up the front drive-line when shifting from 2WD to 4x4 High mode at speed. When the control switch on the instrument panel is turned, the generic electronic module (GEM) recognizes that a shift has been requested and activates the electromagnetic clutch and the relays which power the transfer case shift motor. When the shift motor reaches the desired position as determined by the contact plate position inputs to the GEM, power to the shift relays and motors will be removed. When the transfer case front and rear output shafts are synchronized, the spring loaded lockup collar mechanically engages the main-shaft hub to the drive sprocket. Finally, the front axle collar is engaged and the electromagnetic clutch is deactivated.

Shift Between 2WD and 4x4 HIGH:
Shifts between 2WD and 4x4 HIGH can be made at speed. Listed below are the inputs and outputs needed by the GEM to execute a change between any of these modes.

Feature Inputs:
*4WD Mode Switch (Various resistances).
*Contact Plate Position Inputs A, B, C, D (grounded when closed, open circuit when open).

Feature Outputs:
*4x4 Shift Motor Relay Outputs
*Transfer Case Clutch Relay (grounded when relay is on, open circuit when relay is off).
*4x2/4x4 Vacuum Solenoid (grounded when activated, open circuit when deactivated).
*Cluster Indicators (ground when activated, open circuit when deactivated).

Shifting Into/Out of 4WD LOW:
When shifting into or out of 4WD LOW, the GEM requires that the vehicle speed be less than 5 kph, the brake is applied, and the transmission is in NEUTRAL.

Feature Inputs:
*4WD Mode Switch (Various resistances).
*Contact Plate Position Inputs A, B, C, D (grounded when closed, open circuit when open).
*VSS Sensor (Sinusoid Signal: 0.7V-20V, 2.2 Hz/mph).
Brake Input (battery voltage when brake is depress, open circuit when not activated).
*Transmission Range Sensor (grounded when transmission is in NEUTRAL, open circuit otherwise).
8Start/Clutch Depressed Input

Feature Outputs:
*4x4 Shift Motor Relay Outputs
*4x2/4x4 Vacuum Solenoid (grounded when activated, open circuit when deactivated).
*Cluster Indicators (grounded when activated, open circuit when deactivated).

4WD Mode Switch
A rotary switch allows the vehicle operator to choose between 2WD, 4WD HIGH, and 4WD LOW modes of 4x4 operation.

GEM Module
The Generic Electronic Module (GEM) controls the operation of the 4x4 system

Vehicle Speed Sensor
The vehicle speed sensor (VSS), mounted in the rear of the transfer case, informs the GEM of the vehicle speed.

Transfer Case Shift Motor Sense Plates

The shift motor sense plate, an integral part of the electric shift motor, informs the GEM to the positions of the transfer case

Transmission Range Sensor
Located on the left side of the transmission, this sensor informs the GEM when the transmission is in the NEUTRAL position.

Electric Shift Motor
The electric shift motor, mounted externally at the rear of the transfer case, drives a rotary cam which moves the mode fork and range fork within the transfer case to select between the 2WD, 4WD HIGH, and 4WD LOW positions.

4x4/4x2 Vacuum Solenoids
These two solenoids are attached to the upper RH side of the engine compartment dash, and alternately route vacuum to the vacuum motor which engages/disengages the center axle disconnect collar in the front axle assembly.

4x4 Shift Motor Relay
A module containing two relays which under the control of the GEM, shift the transfer case shift motor between the 2WD, 4WD HIGH, and 4WD LOW modes.

Transfer Case Clutch Relay
An electromechanical relay is used to activate the transfer case clutch within the transfer case.

Good luck and hope this helps,but start with the simple and check the fuses and wire harness. Both white/light blue stripe wires should have 12V in run. The GEM will ground the left side (closest to engine) solenoid to disengage the front axle. It will ground the the right side solenoid (closest to fender) to engage the front axle. If the GEM doesn't see Neutral it will not let the truck come out of 4Lo. If the GEM had water leaking on it it may well be the root of the problem. The shift motor only has power when the GEM sends it a signal to move the shift lever. Once the shift is completed the motor shuts off. There are 2 wires that control the shift motor. A yellow and an orange. The GEM alternates between 12v and Ground to these wires to control which way the motor turns. The GEM uses the transfer case shift relay module to control the power to the motor. There are contact plates inside the shift motor assembly that indicate the position that the shift lever is in. This is what the GEM used to know what the T-case is doing. Any one of these components can fail.







Jan 10, 2010 | 2002 Ford Explorer

1 Answer

1996 ford explorer 4wheel drive will not engage into the hubs need to know how it works


make sure your 4WD switch is working.and fuse is okay.because your 4WD is control by 4 electric shift motors in which drive a rotary cam which moves the mode fork and range fork inside the transfer case to select between 2WD HIGH A4WD - 4WD HIGH AND 4WD LOW RANGE.a shift motor sensing plate on the shift motor monitors the range in which the transfer case is operating a transmission range sensor monitors the gear position of the transmission.which must be in neutral to shift into low.a pair of solenoids one for 2WD one for 4WD.mounted on the upper right firewall route vacuum to the vacuum motor which engages and disengages the center axle disconnect collar in the front axle assembly.a 4 x 4 shift motor relay module contains two GEM controlled relays which shift the transfer case shift motor between 2WD and 4WD modes.a solid state clutch relay activates the A4WDclutch inside the transfer case.

Dec 13, 2009 | 1996 Ford Explorer

3 Answers

I just bought a 2001 blazer 4.3 4wd and it was stuck in 4 low


It should tell you on the Shifter whether or not that you can Shift on the Fly. Check the Manual first if there is one in the Truck. Some Models had this and some Did not. Was an Extra from Factory Option.

Dec 31, 2008 | 2001 Chevrolet Blazer

Not finding what you are looking for?
1991 Jeep Wrangler Logo

360 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...