Question about 1999 Chevrolet 3500

1 Answer

I need help replacing the front wheel bearings

Posted by on

  • brandonbadam Mar 23, 2009

    The bolts are froze on and won't budge. They are corroded and close to being stripped. How should I remove them?

  • Anonymous Apr 04, 2009

    Have a scraping noise in drivers side front wheel on my 2004 chevy truck. Question is it a bearing??

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Where is the oil pump located

Posted on Jan 23, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is it possible to remove and replace front wheel bearings with out a press


In order to remove the front wheel bearings without press hub off the bearing and then the bearing out of the knuckle. To do the first step need a a Support Bridge.It is a special tool. Make bridge and use a general bearing pulled kit to replace bearings. use a "Front Wheel Drive Bearing Removal Adapters Puller Pulley Tool Set Kit" .To replace the bearing, remove front CV shaft taking care not to move the CV shaft too far out .

Nov 06, 2015 | 2002 Kia Rio

1 Answer

Front wheel assembly diagram


For front wheel assembly diagram and replacement,click the link below and go through procedure:----Front wheel hub assembly Diagram and replacing procedure? http://howtobyme.blogspot.in/2012/02/front-wheel-hub-assembly-diagram-and.html
----------Front wheel assembly diagram to replace wheel bearing? http://howtobyme.blogspot.in/2012/02/front-wheel-assembly-diagram-to-replace.html
-------------How to replace Front wheel bearing? http://howtobyme.blogspot.in/2012/02/how-to-replace-front-wheel-bearing.html
-----------Check all 3 links one by one.This will help.Thanks.

Feb 22, 2012 | Ford F-250 Cars & Trucks

1 Answer

2wd front wheel need to replace bearings or hub assembly which is best


A Front Wheel Drive Vehicle Can Have Two Types Of Rear Wheel Bearings: Serviceable Bearings, Or Nonserviceable, Sealed Bearings. When Sealed Bearings Fail, The Bolts Holding The Bearing And Hub To The Axel Or Control Arm Must Be Removed. When Installing The New Bearing Assembly, Torque The Bolts To Specifications.Some Manufacturers require The Use Of New Fasteners When Rear Bearings And Hubs Are Replaced.

When A Serviceable Wheel Bearing Is Used, The Bearing Can Be Disassembled And Packed With Grease.It Is Serviced Like A Front Wheel Bearing On A Rear-wheel-Drive-Car.

Apr 09, 2010 | 2003 Ford Explorer Sport Trac

1 Answer

NEED TO REPLACE WHEEL HUB BEARING OR ONLY THE BEARING


Front Is pressed into hub & knuckle.Rear is a Hub/Bearing Assembly held in by 4 10mm bolts.Will need to pound out with hammer in rear after bolts come out,lots of rust holding them in.Front Knuckle has to come off,Then a large Snap ring,then press out the hub,then the wheel bearing.Hope this helps

May 19, 2009 | 1996 Saturn SL

3 Answers

Right front bearings need lube


Hi if you are refering to the hub bearing it can not be lubed it is a sealed bearing it will have to be replaced

May 04, 2009 | 2002 Buick Park Avenue

3 Answers

Replacing front wheel bearing


those are sealed units and are intergrated with the wheel rotor if the bearings are bad they must be replaced and those are dealer only items. labor for each side is about 1 hour for remove and install per side. unfortunately there are no aftermarket parts available just yet. hope this helps

Aug 28, 2008 | 2003 Mitsubishi Lancer

2 Answers

Think front wheel bearing is going bad on my 2001 ford windstar van how to tell


Jack up the wheel that may have the bad wheel bearing and position your left or right hand at the top of the wheel and the other hand at the bottom of the wheel and rock from top to bottom if there is over 1 cm of play your wheel bearing needs to be replaced and if there is excesive play from left to right your rack ends need to be gresed if the have a grease nipple or replaced hope i was some help

Jul 28, 2008 | 2000 Ford Focus

1 Answer

Noise in front end, sounds like wheel bearings, 110,000 miles, rear end axles and bearings replaced, sounds still present, louder when making left turn when weight of vehicle shifts to front end right side


You say the rear wheel axles and bearings have been replaced, you mention nothing of the front wheels, you have the symptoms of a front wheel bearing being worn out, remove them and check for pitting in the bearing rollers or the bearing races, I am sure you will find a problem. Hope this helps solve your issue with the bearing noise.

Jul 26, 2008 | 2004 Ford Crown Victoria

Not finding what you are looking for?
1999 Chevrolet 3500 Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63572 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...