Question about 2000 Mercury Mountaineer

2 Answers

My rotors are fine so I changed my brake pads and bleed my brake system but now my abs light is on. It came on before but I rebleed my brakes but it still stays on. My brakes are stops better than before so what can be the problem?

Posted by on

  • Anonymous Mar 14, 2014

    I have ignored this light for 2 years. Brakes work fine, even on ice. Antilock system works well.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had the same problem and it turned out to be a bad sensor.
I think ABS are highly overrated. Unless you spend a lot of time tailgating you shouldn't need them. How many years did we go without them and had no problems. That's my take.

Posted on Aug 10, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 62 Answers

Abs sensor or just code stored in computer have vehicle scanned at parts store for free

Posted on Jul 27, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced all brake pads, back rotors and calipers. now brake petal is spongy yet no air in any of the lines. I was told this is a abs problem...Right or wrong and why


keep bleeding you still have air in system if you can positively state that all air is out than check the flex lines but rebleed

Aug 30, 2015 | 2005 Ford Explorer Sport Trac

2 Answers

My breaks wont work after changing the front rotars, calipars and pads. I bleed all four breaks starting with the back passenger side then back drivers side then front passenger side then front drivers...


As a general rule, if you have ABS you might have to cycle the pumps and valves to purge the old fluid out of the unit. This is either done via a dealer scan tool, a purge valve/bleeder valve on the ABS unit, or a less than ethical way. Drive your car and heavily engage the ABS, you know what I'm talking about.
Then you will need to repeat the bleeding process that you have already done.
Normal non ABS brakes, bleed once.
ABS brakes, bleed, cycle then bleed again.

Aug 07, 2011 | Chrysler Cirrus Cars & Trucks

1 Answer

Replaced front calipers,master cylinder,front and rear pads and resurfaced all four rotors.I bled the brakes starting with right rear then left rear, right front then left front and still feels like there...


did you bench bled master? if yes do you have abs system,if so you must bleed at abs block,if it has bleeders, if not then you must line bleed all 6 lines.2in from master 4 out to wheeles. then rebleed wheel in cylinder.If you have bleeders at abs block you dont to rebleed wheels. best dun with powerbleeder. hoooooops this helps

Jun 12, 2010 | 2000 Mercury Grand Marquis

1 Answer

Video for replacing front brakes pads and rotors on a 2004 ford e


Hello,
ccr20011001bb00.jpg Brake Bleeding
Purging air and moisture from your binders
CarCare - Maintenance - Brakes

ccr20030701as00.jpg ABS Speed Sensor Service
A clean sensor is a happy sensor
CarCare - Maintenance - Brakes

ccr20030701db00.jpg Drum Brakes - Rear Brake Drum Adjustment
It's stupid not to adjust your rear drum brakes
CarCare - Maintenance - Brakes

ccr20050201rr00.jpg Replacement Rotors
Friction, brake rotors, and you
CarCare - Maintenance - Brakes

ccr20050501pb00.jpg Power-Bleeding Brake Systems
Air today, gone tomorrow
CarCare - Maintenance - Brakes

ccr20050701bp00.jpg Replacing Brake Pads
How to replace worn pads
CarCare - Maintenance - Brakes

ccr20071101bs00.jpg Bleeding Power Steering
Getting rid of that air in there
CarCare - Maintenance - BrakesThanks

May 29, 2010 | 2004 Ford Escape

1 Answer

I have a 95 mercury sable and a little while back our abs light came on well the finances werent there at the time to have it checked so now i had to change the complete brake system on the drivers rear....


If you completely overhauled the brake system with new brake lines and pads, then the problem would be that air was not completely removed from the brake system. will have to bleed the brake system to remove the air traped in the lines and behind the brake calipers. hope this will help you.

May 10, 2010 | Cars & Trucks

2 Answers

I have a 1998 bravada, I replaced all 4 rotors, pads and both rear caliper brackets, but the right rear brake is dragging. Do I need a new caliper and if so how do you bleed the brakes. Thanks Walt


id bleed them first best if u have two people while u are doing this on ths caliper top the will be a bleeder valve have someone pump brakes and hold them down as u turn the bleeder after brake ped goes to the floor tighten bleeder up and have them pump brakes back up when u loosen bleeder u should here air come out if not u are fine go to next wheel do same on all for wheels

Oct 23, 2009 | 1998 Oldsmobile Bravada

1 Answer

Changed brake pads and fluid. Brake light/ABS light still lit.


Go back around and check to make sure you didnt accidentally pinch or cut a brake pad sensor. Also the ABS modules on VAG cars are pretty crappy.

Sep 11, 2009 | 1999 Audi A4

2 Answers

1999 Chevy Tahoe- Soft Brake Pedal


Try having the dealer flush and bleed your system. It is very hard to bleed ABS systems yourself and have safe brakes that still work afterward. Bleeding non-ABS brakes yourself is easy not the same for ABS brakes. Valving, sensors and what-not require a tech and the correct equipment in my opinion. You do it wrong and you could ruin your ABS system. Do that and see if they firm up. I replaced my brake shoes/pads at the same time all new everything in back, drums/springs everything and new rotors up front. then I had the chevy dealer flush, refill and bleed system. Stiffer pedal and brakes work better. Keep in mind the brakes on 99 Tahoes are inaedequate, require new rotors often, heat up and fade/glaze pads regularly. I replace my pads long before they wear down because they glaze up and start fading early. I'll rough em up once maybe, next time, new ones. Every two brake jobs, new rotors for me. Just how it is. They will stiffen a bit and work better but they will never be awesome brakes. Just how it is on 99 and earlier Tahoes. Hope it helps. Very important to bleed correctly though. I'll bleed my 83 Toyota 4x4 myself but not the Tahoe.

Aug 06, 2009 | 1999 Chevrolet Tahoe

3 Answers

ABS light on after replacing the front and rear brake pads .


u will need to check the wheel speed sensors behind the brake rotors to see if they got damaged or disconnected during the brake job, as long as the ABS light is on the Anti-lock brake system is disabled, regular braking without the need of ABS will feel fine.

Apr 01, 2009 | GMC Sierra 2500 Cars & Trucks

Not finding what you are looking for?
2000 Mercury Mountaineer Logo

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...