Question about 2004 Ford Explorer Sport Trac

1 Answer

Over drive button is not working when I press it.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    MVP:

    An expert that gotĀ 5 achievements.

    Master:

    An expert who has achieved Level 3.

    Sergeant:

    An expert that hasĀ over 500 points.

  • Master
  • 450 Answers

Is your tranny working good. if so check your fuses hope this helps

Posted on Mar 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Possible reason why 04 chevy tahoe 4wd works up in air on lift but not on ground


the residual force makes it look like its working on a lift ,
check your wheel sensors the speed sensor determines how fast each wheel is turning say in the snow , if the sensor fails it wont go into 4 wheel drive.

Feb 19, 2015 | Cars & Trucks

1 Answer

Digital speedometer display inop. tap on dash & it comes on


open the hood and find the speedometer cables according to your auto's manual, check to see if they are securely connected to the ports on back of speedometer. if this doesn't work. find the function button front of speedometer press and hold while starting engine, will enter function mode,press button repeatedly untill you come to auto. press and hold button untill "-" appears then release button , unit will show on screen,wait untill a line of zero's appear on screen then drive around untill you go over one mile, stop the car and press the function button again,the speedometer is now recalibrated this usually fixes many errors

Mar 15, 2014 | 2003 Ford Crown Victoria

1 Answer

I recently had my front dirver side tire replace on my 2006 330i. The red flat tire monitor indicator is on and I cannot get it to reset. I checked all of the tires for the correct pressure and they all...


TURN IGNITION ON POSITION.PRESS THE LEFT BUTTON THERE ARE TWO BUTTONS BUT PRESS THE LEFT BUTTON UNDER THE I DRIVE CONTROLLER.TO ACCESS MENU IN MULTIFUNCTION DISPLAY.PRESS I DRIVE CONTROLLER ROUND BUTTON.TURN I DRIVE CONTROLLER TO SELECT VECHICLE SETTINGS.PRESS I DRIVE CONTROLLER TO CONFIRM SELECTION.TURN I DRIVE CONTROLLER TO SELECT FTM.PRESS I DRIVE CONTROLLER TO CONFIRM SELECTION. START ENGINE TURN I DRIVE CONTROLLER TO SELECT SET TIRE PRESSURE.PRESS I DRIVE CONTROLLER TO CONFIRM SELECTION.TURN I DRIVE CONTROLLER TO SELECT YES.PRESS I DRIVE CONTROLLER TO CONFIRM SELECTION.DRIVE VECHICLE TO COMPLETE RESET PROCEDURE.THE SYSTEM WILL LEARN NEW VALUES WHEN THE VECHICLE IS DRIVEN.DRIVE VECHICLE UNTIL YOU SEE MESSAGE STATUS ACTIVE DISPLAYED WHEN INITIALIZATION IS COMPLETE.

Feb 01, 2011 | BMW 330 Cars & Trucks

1 Answer

I bought a toyota vista ardeo with shiftmatic on the steering wheel and I dont know how to use it.kindly help.


Hi, i have the same kind of Ardeo and this is how the steer matic shift works.
Stop vehicle and shift gear lever to DRIVE position then press on the steermatic shift button and M will high light above the top of the semi auto shift high lighter to show that you are in the steering wheel gear shift manual mode.At this point you can use the down shift buttons on the front part of the steering and the up shift buttons on rhe rear side of the steering.the down shifted or up shifted gear will high light on the dash.if you want to boot back to semi or automatic drive press steermatic button again.ENJOY YOUR DRIVE

Jul 01, 2010 | Cars & Trucks

2 Answers

Can't shift from park, button is hard to push in.


press the brakes down hard and leave it there for a while and keep pressing the gear button and eventually you'll be driving

May 27, 2009 | 2003 Mitsubishi Galant

1 Answer

1998 Chevy Blazer 4x4, $ wheel drive won't work (both 4hi & 4lo )


Reset the computer by disconnecting the battery. This should solve this. nutetral is for the four lo only to engage.

Mike

Jan 26, 2009 | 1997 Chevrolet Blazer

1 Answer

4*4 not eagaging light keep flashing


Wat i did was to install a reset button on the 4wd computer and each time it flash . i put it into neutral and press the button . For example If i mistakinly press the 4wd while in park the indictor will flash.I then have to put it in nuutrat press the button and it will stop flash and either select or come off from flashing.

Oct 13, 2008 | 2008 Toyota Tacoma

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...