Question about 1984 Isuzu Pickup

1 Answer

I have a 1986 pup 4 cyl,4speed.I cant seem to keep the electric choke adjusted correrctly.Is it possible tha there are problems elswere in the carb?or just the choke.

Posted by on

  • Anonymous Sep 09, 2008

    vacuum diagram


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

I have a 1984 pup 4 cyl 4 speed.i cant seem to keep the electric choke adjusted it possible tha there are problems elswere in the carb?or just the choke

Posted on Nov 13, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

I have a 1986 pontiac fiero 4 cyl. 5 spd . the clutch is moving fine , and so are the cables , but when you let the clutch out , nothing happens , the car does not move .

Does the pedal have "free play" at the top? Perhaps some adjustment is possible. If not, may be time to replace clutch disk.

Jan 14, 2015 | 1986 Pontiac Fiero

1 Answer

Car starts but wants to die out right away have to play with the gas padle

A 1986 Mustang with a 4 cyl engine should have a carb and a choke. It sounds like the choke is not closing and-or the fast idle cam is not raising the idle speed until the choke opens.

Feb 02, 2013 | Cars & Trucks

1 Answer

1986 toyota truck electric choke

Is it hard to start? The choke has some notches on the side by the electric choke to lean...If hard to start cold, loosen choke screws on side and turn the dial toward close (rich) retighten adjustment screws and recheck performance...If choke stays on to long after warm up (idles fast) adjust the choke toward open or lean position. Try no more than 2 notches either way between tests...Hope this helps.

Jan 21, 2013 | Cars & Trucks

1 Answer

Is it possible to put a manual choke on a 83 Ford Ranger with 2.o 4 cyl. ?

You would have to take a look at a conversion kit and see if there is a plastic cup that will fit your carb. The cup is used in place of the electric choke coil on the carb now.

Sep 18, 2012 | 1983 Ford Ranger

1 Answer

Replaced Carb with a Edelbrock electric choke and now the truck will not start...Put new distirbortor on and new plugs and new wires...

The choke may be out of adjustment if the choke blade is fully closed you may have to adjust until partially open. The other possibility is the distributor is not installed correctly or the plug wire may be mixed up.

Feb 19, 2011 | 1986 Ford F 250

2 Answers

Procedure of tappet adjustment

make sure engine is warmed up. Put cylinder one at top dead center,remove the valve cover,loosen all adjustment lock nuts,adust intake and exhaust valves on cyl #1 and intake valve on #2 and exhaust valve on #3. now rotate crankshaft 360 degrees clockwise, now adjust intake valves on cyl#3 and cyl #4 and exhaust valves on cyl #2 and cyl tighten lock nuts and install valve cover. specs are intake valves 25mm clearance and exhaust 28mm clearance, use a feeler gauge,heres a picture to show you where to check clearance.7675a52.gif

Mar 14, 2010 | 1986 Suzuki Samurai

1 Answer

I have an 1986 dodge aries se station wagon that is having some problems. The engine sputters out when ever it is chilly out. No matter what the engine tempt is it seems to be choking when its even...

Sounds to me like the automatic choke assembly is out of adjustment or not functioning correctly. On a cold day, you will note that the choke assembly is closed, try manually opening it and proping it open to see if this improves the problem. If your not sure where the choke assembly is, I suggest you buy a Hanes Repair Manual for this vehicle from your local auto parts store to help troubleshoot this problem.

Oct 10, 2009 | 1986 Dodge Aries 4 Door

1 Answer

Engine has a fast idle and wont kick down. Ford Ranger 2.0L 4 cyl

sounds like a stcuck choke to me as well have you tried spraying the choke with lube or installing a new one?

Aug 26, 2009 | 1987 Ford Ranger

1 Answer

When setting the timing gears, where do you set the distributor?

from memory no4 on dissy when timing marks on cam timing in correct position, no 1 cam lobes should be "rocking" and no4 cylinder should be at top dead firing stroke(ignition)should be notch in dissy when cap is off or set so rotor button is lined up with cyl no 4 ht lead position

Jun 06, 2009 | 1986 Isuzu Pickup

1 Answer

Trouble starting 1986 5th ave

If ignition system is in good physical condition, check choke adjustment. When cold it should be closed, vacuum control should pull it further open as soon as it starts (both can be adjusted by bending control rods) choke is both heated and electrically controlled. some operate better with electric unplugged. Fuel pressure should be close to 5psi. Check/change filter if age is unknown.

Mar 13, 2009 | 1986 Chrysler Fifth Avenue

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

372 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

70365 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides