Question about Chevrolet Lumina

1 Answer

I have a 3 wire cable running from the fromt main bearing area of my '96 Lumina to ??? Where do I connect. I'm trying to button up after replacing intake gaskets

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 62 Answers

Its ether on backside if intake near coil pack or on front near throttle bodie.

Posted on Jul 27, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Had to replace fuse inline alternator how can I transfer the inline fuse to a different wire


the cable /fuse to alternator has nothing to do with the start and run function if the battery is charged up and in good condition ,sounds like the main battery cables have a bad contact/connection or battery is shot<follow battery cables and remove all points of connection in engine bay area clean contacts with sandpaper and resecure all connections 1 AT A TIME! to make sure none are swapped around by mistake ) on both earth cable/negative and the positive/power cables,make sure terminals on battery are clean and tight , try boosting/jump starting your battery with jumper cables connected from another cars battery positive to positive .........negative to negative and see if it starts ,i doubt the problem of starting up is the alternator unless battery is flat and not being charged by alternator ,by jump starting with another baterry will give you the answer once all baterry cables and connections are clean and secure

Jan 15, 2014 | 2006 Ford Focus

2 Answers

My lumina will jump start and starts several times then goes dead with clicking noise


I would say if the car stays running after u jumped started it I would replace the battery

Jan 11, 2013 | 2001 Chevrolet Lumina

1 Answer

96 Lumina 3.1 won't start. It runs when I spray starting fluid in the throttle body. It has 42psi fuel pressure at the fuel rail. Is it bad injectors?


It is not bad injectors, it is lack of injector electrical pulse, never would all the injectors fail at once. See if you have 12 volts (use a 12 volt probing test light, avail at any auto parts store for less than $5) to one wire of the two wire connector of each injector with the ignition key in run position. If the test shows no hot wire at the injector connectors then check fuses marked ECM1 and ECM2 in the under-hood fuse block. If they are popped then you have a shorted harness or component.

Jun 27, 2012 | 1993 Chevrolet Lumina

1 Answer

I have a 95 chevy lumina. this morning my wife said there was smoke coming from the battery area and it smelled like an electrical burning smell. I checked it out and it looked like the ground wire running...


if the wire is not connected to the frame or to the terminal correctly it will get hot or even burn the cover off,make sure both ends are metal to metal and tight,then cover in silicon jelly to stop the air getting to the metal and rusting (which will also cause a bad contact.

Jan 28, 2011 | 1995 Chevrolet Lumina

1 Answer

Looking for a spark plug wire firing order skematic for 96 chev lumina 3.1L Engine. can you supply one?


Firing Orders NOTE: To avoid confusion, remove and tag the spark plug wires one at a time, for replacement.
3.1L (VIN M) engine
Firing order: 1-2-3-4-5-6
Distributorless Ignition System 79223g18.gif

Jul 16, 2010 | 1996 Chevrolet Lumina Mini

1 Answer

What is the best way to change a brake light switch? It's on a 1995 Chevy Lumina car.


1993-96 Vehicles
See Figure 2

0900c1528006832d.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Brake light or stoplamp switch mounting-1995 vehicle shown

  1. Disconnect the negative battery cable. -96 vehicles, remove the driver's side instrument panel sound insulator panel.
  2. Detach the switch electrical connectors.
  3. Remove the switch from the brake pedal bracket.

To install:
  1. Position the switch to the brake pedal bracket.
  2. Attach the electrical connectors.
  3. If removed, install the driver's side instrument panel sound insulator panel.
  4. Connect the negative battery cable.

Nov 18, 2009 | 1995 Chevrolet Lumina

1 Answer

Replaced starter in 97 lumina no power


check your fudes under the hood and under drivers side dash

Sep 05, 2009 | 1997 Chevrolet Lumina

1 Answer

Firing order and camshaft sensor for a 96 chevy lumina 3.1 v6


Here is a diagram of your motor with the firing order:

704b0d7.gif

Mar 19, 2009 | 1996 Chevrolet Lumina Mini

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...