Question about 1997 Hyundai Elantra

1 Answer

How do I get the back brakes drum off

How do i get the back brake drum off

Posted by on

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 97 Answers

Gently tap with rubber hammer while pulling

Posted on Jul 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake shoes on 1987 f250 460 1987 2 wheel drive how to replace


Lift the front of your Ford F-250 off of the ground using a jack and jack stands. Remove the wheels from the Ford with a lug nut wrench to prepare the truck for servicing. 2 Open the hood on the engine compartment and take the lid off of the master cylinder that bolts to the brake assister on the driver's side firewall.3 Remove the hex-head bolts on the back of the brake caliper with a socket. With the bolts removed, pull the caliper off of the Ford's brake rotor.4 Pull the old brake pads out of the caliper and discard them. Squeeze the brake piston back into the backside brake caliper with pliers, and then insert the new pads into the brake caliper.5 Pull the rotor cap cover off the middle of the rotor with a screwdriver and use a socket to remove the nut located behind the cover.6 Pull the rotor off of the wheel spindle.7 Remove the old wheel bearings from the brake rotor and insert them into the new rotor. If the old wheel bearings are worn, replace them with new bearings.8 Slide the new rotor onto the wheel spindle and secure it using a bolt and socket. After you tighten the bolt, press the cover back onto the rotor.9 Place the caliper on the rotor and secure it with a socket and hex-head bolts. 10 Duplicate the process on the passenger side of the F-250. 11 Close the master cylinder after putting the wheels back on the Ford and lowering it to the ground. Press on the brake pedal to seat the pads against the rotor
Replace the F-250's Rear Brakes 1 lift the rear of the Ford F-250 off the ground with a jack and jack stands. Remove the wheels from the Ford with a lug nut wrench.2 Place a strip of paint on the back of the brake drum and rear brake drum cover so you can position the brake drum orrectly when you put it back on. If you plan to install new brake drums on your Ford F-250, skip this step. 3 Place the brake drum puller on the brake drum and pull the drum from the wheel hub. The method for attaching the brake drum puller depends on the brake drum puller that you use. 4 Remove the springs that attach the brake shoes to the wheel hub by pulling them off with pliers.5 Lift the old brake shoes off of the wheel hub and place the new brake shoes on the wheel hub. Secure the new shoes with the springs.6 Pound the brake drum onto the axle hub with a rubber mallet.7 Duplicate the process on the passenger side of the Ford.8 Put the wheels back on the F-250, lower it to the ground and, then press on the brake pedal to seat the shoes against the brake drum.

Oct 14, 2011 | 1988 Ford F 250

1 Answer

Replace rear breaks


Rear Drum Brakes-let me know if you have rear disc brakes. Brake Drums Removal & Installation Remove the access hole plug, then back off the adjusting screw 88009g07.gif
Exploded view of the drum brake system 88009g06.gif

  1. Raise and safely support the vehicle with jackstands.
  2. Mark the relationship of the wheel to the axle flange to help maintain wheel balance after assembly.
  3. Remove the tire and wheel assembly.
  4. Mark the relationship of the brake drum to the axle flange. CAUTION
    Do not pry against the splash shield that surrounds the backing plate in an attempt to free the drum. This will bend the splash shield.
  5. If difficulty is encountered in removing the brake drum, the following steps may be of assistance.
    • Make sure the parking brake is released.
    • Back off the parking brake cable adjustment.
    • Remove the access hole plug from the backing plate.
    • Using a screwdriver, back off the adjusting screw.
    • Install the access hole plug to prevent dirt or contamination from entering the drum brake assembly.
    • Use a small amount of penetrating oil applied around the brake drum pilot hole.
    • Carefully remove the brake drum from the vehicle.
  6. After removing the brake drum it should be checked for the following:
    • Inspecting for cracks and deep grooves.
    • Inspect for out of round and taper.
    • Inspecting for hot spots (black in color).
To Install:
  1. Install the brake drum onto the vehicle aligning the reference marks on the axle flange.
  2. Install the tire and wheel assembly and hand-tighten the lug nuts.
  3. Carefully lower the vehicle, then tighten the lug nuts to 100 ft. lbs. (140 Nm).
  4. Road test the vehicle.
prev.gif next.gif

Feb 14, 2011 | 1998 Chevrolet Lumina

1 Answer

1998 ford escort se hand brake need adjusting. doesn't hold.


Try to adjust the rear brakes tighter at the shoes, if you have drum brakes. May require taking the drum off and adjusting the adjuster. Or, adjusting it from the backing plate access hole if there is one.

Be sure to check the cables to make sure they are not broken anywhere between the hand brake lever and the back brakes.

Good luck on this repair.

ADJUSTMENT


  1. Raise and safely support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake drum.
  4. Using a brake adjusting gauge, measure the inside diameter of the brake
    drum.
  5. Compare the brake drum measurement to the brake shoes.
  6. Adjust the brake shoes by inserting a brake adjustment tool into the knurled
    quadrant of the rear quad operating lever and adjust the shoes to the same
    measurement as the brake drum.
  7. Install the brake drum.
  8. Install the wheel and tire assembly.
  9. Lower the vehicle.
  10. Check the brake system operation by making several stops while driving
    slowly forward.


prev.gif next.gif

Nov 02, 2010 | 1998 Ford Escort

2 Answers

Back brake drums grinding


Take tires off then inspect rear brake shoes if okay and not down to the metal service the drums with sand paper and put them back on you might have to replace the drums and shoes!

Dec 24, 2009 | 1993 Ford Escort 4 Door

4 Answers

03 SILVERADO DRUM BRAKES


TO REMOVE BRAKE DRUM.IF ITS HAS PRESSED METAL WASHERS.CUT THEM OFF.TO GET A STUCK BRAKE DRUM. OFF. REMOVE THE PLUG FROM BACKING PLATE.AND PUSH THE PARKING BRAKE LEVER OFF ITS STOPS.WITH A SCREW DRIVER AND BRAKE ADJUSTING TOOL.TURNING ADJUSTER STAR WHEEL UPWARD.TO RETRACT THE SHOES.THEN REMOVE DRUM.

Jul 26, 2009 | 1999 Chevrolet 3500

2 Answers

Brake drums


the brake shoes are likely stuck in the grooves worn into the drum. You need to back off the brake shoe adjusting wheel to loosen the brake shoes.
Also, the face of the drum usually has a couple of threaded holes you can screw bolts into to help pull the drums toward you.

First, hit all the way around the brake drum with a big hammer to loosen the drum from the center hub.
Then, istall the screws to help pull the drum.

to back off the adjuster with a screwdriver:

  1. NOTE: If the brake drum will not come off, follow these steps.
  2. Loosen the brake shoe adjusting screw nut (2047).
  3. Using a screwdriver, move the brake shoe adjusting lever (2A176) off the brake adjuster screw (2041).
  4. NOTE: Move the adjustment tool handle downward to loosen the brake shoe adjusting screw nut.
    Use the Brake Adjustment Tool to loosen the brake shoe adjusting screw nut.
0e94acc.gif
please give a good rating if this helps.

May 03, 2009 | Mazda B3000 Cars & Trucks

2 Answers

2000 tahoe rear drum brakes, fix


Below is a description of how to replace the rear brake shoes. You didn't mention if it is 2 wheel or 4 wheel drive.
Hope this helps.
Regards,

Dust and dirt accumulating on brake parts during normal use may contain asbestos fibers from production or aftermarket brake linings. Breathing excessive concentrations of asbestos fibers can cause serious bodily harm. Exercise care when servicing brake parts. Do not sand or grind brake lining unless equipment used is designed to contain the dust residue. Do not clean brake parts with compressed air or by dry brushing. Cleaning should be done by dampening the brake components with a fine mist of water, then wiping the brake components clean with a dampened cloth. Dispose of cloth and all residue containing asbestos fibers in an impermeable container with the appropriate label. Follow practices prescribed by the Occupational Safety and Health Administration (OSHA) and the Environmental Protection Agency (EPA) for the handling, processing, and disposing of dust or debris that may contain asbestos fibers.

  1. Raise and support the vehicle safely.
  2. Mark the relationship of the wheel to the hub and remove the wheel.
  3. Mark the relationship of the drum to the hub and pull the drum from the brake assembly.

If the brake drums have been scored from worn linings, the brake adjuster must be backed off so the brake shoes will retract from the drum. The adjuster can be backed off by inserting a brake adjusting tool through the access hole provided. In some cases the access hole is provided in the brake drum. A metal cover plate is over the hole. This may be removed by using a hammer and chisel.
To install:
  1. Align the mark on the drum to mark on hub and install drum
  2. Align the mark on the wheel to mark on drum and install wheel
  3. Adjust brake lining as needed. Pump brakes

  1. Raise and support the vehicle safely.
  2. Mark the relationship of the wheel to the hub and remove the wheel.
  3. Mark the relationship of the drum to the hub and pull the drum from the brake assembly. If the brake drums have been scored from worn linings, the brake adjuster must be backed off so the brake shoes will retract from the drum. The adjuster can be backed off by inserting a brake adjusting tool through the access hole provided. In some cases the access hole is provided in the brake drum. A metal cover plate is over the hole. This may be removed by using a hammer and chisel.

To install:
  1. Align the mark on the drum to mark on hub and install drum
  2. Align the mark on the wheel to mark on drum and install wheel
  3. Adjust brake lining as needed. Pump brakes

  1. Raise and support the vehicle safely.
  2. Mark the relationship of the wheel to the hub and remove the wheel.
  3. Mark the relationship of the drum to the hub and pull the drum from the brake assembly. If the brake drums have been scored from worn linings, the brake adjuster must be backed off so the brake shoes will retract from the drum. The adjuster can be backed off by inserting a brake adjusting tool through the access hole provided. In some cases the access hole is provided in the brake drum. A metal cover plate is over the hole. This may be removed by using a hammer and chisel.

    0900c15280247e6e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the brake drum

To install:
  1. Align the mark on the drum to mark on hub and install drum
  2. Align the mark on the wheel to mark on drum and install wheel
  3. Adjust brake lining as needed. Pump brakes

Mar 27, 2009 | 2000 Chevrolet Tahoe

1 Answer

Back drum brakes


Remove the rubber plug at the back of the backing plate. Take a brake adjusting tool or screw driver through the hole and turn(pry) the brake adjuster to back off the brake shoes. There is a ridge worn in to the brake drum and that is keeping the brake drum on, even if you can wiggle it.

Mar 23, 2009 | 1988 Dodge D-Series Pickups

1 Answer

Putting brake drum back on


Did you try backing the brakes off and then once you get the drum back on readjust the brakes.

Feb 28, 2009 | 1999 Mercury Mystique

1 Answer

Back brake


On drum brakes there is a pad adjustment wheel, use it to back the pads off far enough from the drum that the edge of the drum clears the pads

Jun 11, 2008 | 1995 Dodge Caravan

Not finding what you are looking for?
1997 Hyundai Elantra Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...