Question about 1989 Mercedes-Benz 190

1 Answer

Rear power window will not roll up and can not get door pane off to service, located right rear door

Posted by on

1 Answer

To take panel off you.
1.Unscrew door lock knob.
2.Open door, look where it latches,Take the little black piece off.
3.There is a U-shaped plastic piece at the top of the handle you close the door with,Carefully pry it out.
4.Take the 10mm bolt out.
5.The black plastic piece that holds the chrome handle you open the door with,Slide it to the right.
6.Lift the whole panel straight up.
7.Unplug window switch.
If you pull out the door clips will pull off, You can glue they back on with some 2 part apoxy.
Good Luck

Posted on Aug 17, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need help with power window issues.


I'm thinking this is a broken wire issue to the rear. Pull the switches out in the rear and check for good powers and grounds. As far as the slow window operation.. that is just a window motor that is near its end.

Aug 31, 2015 | 1992 Subaru Loyale

1 Answer

2007 denali drivers side back door window will roll down but not back up


Problem should be in the rear door switch. The motor is powered from both switches.

Jul 21, 2012 | GMC Yukon Denali Cars & Trucks

1 Answer

Door panel removal for window switch repair


This is theinstruction on how to remove door panel of Toyota camry 1. Openthe door as wide as possible and roll the window up completely. Locate andremove five screws and two clips in the door panel. Two screws are located atthe rear of the panel, another two are located under the arm rest, one near thelight and the other in front of the light. The last screw is located in thefront of the arm rest behind a triangle shaped plastic panel, directly belowthe door handle. Pry this panel up with a flathead screwdriver to remove thescrew underneath. The two clips are near the front of the door and are smallplastic circles. Push them in with a small screw driver and pull them out. 2. Remove the plastic trim around the doorhandle. Use a flathead screwdriver or prying tool to pop the plastic out fromthe door panel. Wiggle it around until it comes loose from the door handle. 3. Use a flathead screwdriver or prying tool atthe bottom edge of the door. Pry away from the door until the clips under theedge pop out. These are plastic clips under the edge of the bottom and sides ofthe panel. Gently pop them out from the entire door panel. The top of the panelis held in place by the window trim. Move the panel back and forth until it isfree from the window trim. 4. Unclip the wire connectors and wires with aflathead screwdriver. The door panel is now free from the door.

Nov 29, 2010 | 1995 Toyota Camry

1 Answer

The power window switch on the driver's door of my 2005 civic hybrid for the right rear passenger window only rolls the window down, not up (the switch on the passenger window door works fine). I'm having...


If your window rolled down than means your window regulator is getting power. It's most likely your switches are bad.

When you use the down switch it supplies power to your window regulator. When you use the up switch it supplies power also but the polarities are switch which causes the window to roll in the opposite direction.

Sounds like your up switch is not making a complete connection to make your window roll back up.

For parts, check this LINK.

Good luck.

Jun 02, 2010 | 2005 Honda Civic

1 Answer

The drivers side rear window does not work. It does side down, and when the power switch is press the motor turns on. could the window be off its track or does the window unit need replaced?


It sounds like the window may be off its track. All that needs to be done is to remove the inner door panel. Be careful to pry the clips very gently. They break easily. However, most auto parts stores carry replacements. Once the door panel is off, remove the plastic sheeting that covers the door frame. It's attached with a mastic adhesive.
Once you have a clear view of the window rail, carefully pull the pane up and set the glass on the track. You may need to apply some silicone in the track to keep the glass in place.

Then, test the alignment by pressing the power button and roll the window up and down. With the window closed, replace the plastic sheeting and the door panel.

That should do it.

Oct 09, 2009 | 1994 Lincoln Town Car

2 Answers

Divers window won't roll up my Camry


No won't be fuse. My guess is there is something faulty with the main controller. You could probably verify this by trying the switch on right rear passenger door. If it works there then the problem is at the main controller in the driver door. Could be a loose wire or the switch itself is broken.

May 13, 2009 | 1986 Toyota Camry

1 Answer

The right rear electric window won't roll up all


the window regulator is going bad,it has a up cable and a down cable so I would replace it before it wont go up at all,they are pretty inexpensive around $70.00 at a decent parts house,its a pretty simple job, remove the door panel,locate window to regulator bolts.remove them,take glass out thru top, locate 3 bolts that hold motor assy. remove them take bolts holding regulator in place remove them,take motor and regulator out thru holes in door.you can do it! have a good day DB

Feb 27, 2009 | 1991 Honda Accord

2 Answers

1994 jeep grand cherokee power window problem


most of the time it is wires in the drivers door that break in the loom

Feb 20, 2009 | 1994 Jeep Cherokee

1 Answer

Power windows


This means you need to head to the junk yard and replace the unit that controlls all the windows from the drivers seat. Very simple fix. Good luck

Dec 30, 2008 | 1997 Isuzu Rodeo

1 Answer

1994 jeep grand cherokee power window problem


try replacing the master switch it maybe malfunctioning due to wear.or may have shorted out by getting wet or something.since it is the primary control for all windows and power door locks.

Dec 05, 2008 | 1994 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

yadayada
yadayada

Level 3 Expert

70347 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...