Question about 1997 Chevrolet S-10 Pickup

1 Answer

I have a 1996 chevy silverado and the truck turns over but won't start, engine light was on and said I needed to change the map sensor which I did and it quit running and won't start what else could it be

Posted by on

1 Answer

Buy nuw truck

Posted on Oct 07, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change BANK 1 & 2 o2 sensors 1 & 2 on 1996 chevy silverado


SORRY I DONT HAVE A PICTURE BUT BANK 1 & BANK 2 SENSOR 1 REFER TO THE LEFT AND RIGHT SENSORS BEFORE THE CAT CONVERTER ( UPSTREAM) SENSOR 2 REFERS TO THE SENSOR AFTER THE CAT (DOWNSTREAM) YOU TUBE HAS GOOD VIDEOS

Jan 20, 2015 | Cars & Trucks

1 Answer

My 1996 chevy silverado runs so poorly that it vibrates it pulls hills about 25 mile an hour i cant give it throttle because it would fall on its face


is your check engine light on? if so, have the codes read at your local auto parts store. having these codes can narrow your search to find the cause of your problems

Autozone.com has a great site that tells you how to test sensors and hard parts. become a member and search their repair guide

These are things I would consider;

Clogged fuel filter / injectors / contaminated fuel
Manifold Absolute Pressure (MAP) Sensor
Mass Air Flow (MAF) Sensor
Throttle Position Sensor (TPS)
Clogged Catalytic Converter
Worn / corroded ignition parts.

Jan 13, 2011 | 1996 Chevrolet K1500

1 Answer

Location of map sensor on my 1996 chevy k1500 truch vortex v8 5.0


The M.A.P. sensor is located on the upper intake manifold plenum. It has a plug with 3 wires connected to it, and a vacuum hose connected to it. to chek the sensor you'll need a volt meter. you can insert the positive lead into the backside of the terminal of the light green wire (with the plug still plugged into the sensor). Put the negative lead from the volt meter and ground it to a solid chassis ground. Turn the key to the on position (DO NOT START THE ENGINE). Your voltage should read 4.0 to 5.0 volts. Now start the engine. at idle your voltage should read 0.5 to 2.0 volts. If your volts read in those ranges your map sensor is good.

Mar 06, 2010 | 1996 Chevrolet C1500

3 Answers

94 chevy 5.7 350 need to reset timing what do i need to do?


start engine and bring to normal operating temp. unplug the base timing connector located in the distributor wiring harness tan wire with a black stripe use a timing light and set timing to 0 degrees at idle the timing marks are on the crankshaft pulley and a tab on the timing cover with numerical indications

Jan 01, 2010 | 1994 Chevrolet Silverado 2500

2 Answers

2005 chevy silverado won;t start.


i had the same problem, and it turned out the coil pack was moulding inside wich stopped the spark all together, i ended up changing my coil pack and putting on new wires because the ends connected to the coil were very corroded and that cures the not running part just fine


enjoy

Jul 01, 2009 | 2003 Chevrolet Silverado 2500HD

1 Answer

I have a 1999 chevy silverado 5,3 i had the oil changed three weeks ago. now my light comes on tellin me to change my engine oil. what could cause this?


  • its a sensor that lets you know to change oil. 1st turn key on start possession don't start, 2nd pump gas pedal three times fast not real fast then after the third time turn key back to off then start the vehicle this should reset the light!!

Mar 31, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

OXYGEN SENSOR OR FUEL PUMP?


Change the fuel filter, check the fuel pressure, then pull the tank and replace the pump if the pressure is below spec.

Mar 18, 2009 | 1996 Chevrolet K1500

2 Answers

I have a 1996 Chevy astro Van I have problems starting.


im having the same problem with mine..the service engine soon light came on.. i hooked up the electronic diognostic reader (obd2) to the van and a p0108 code came up (map/baro circuit high input). i am going to take off the engine cover tomorrow inside the van behind the center console to get to the map sensor to see if it is loose and check the vaccuum lines and change the spark plugs while im back there.. from what im told.. thats how u fix that problem.. also u may need to reset the sensor electronically.. that i have no idea how to do yet but i am going to purchase the book from strauss

Nov 18, 2008 | 1996 Chevrolet Astro

Not finding what you are looking for?
1997 Chevrolet S-10 Pickup Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...