Question about 1999 Jeep Cherokee 4WD

1 Answer

Jeep in what order do the wires for blower resistor for 1999 grand cherokee go

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 508 Answers

All you should have to do is place the plug end back onto the spades they came off of.

Posted on Feb 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the wiring diagram for a blower motor resistor on a 1999 jeep cherokee sport


The black tan wire on one end goes to the blower motor.
Tan for low is next, lt green is medium 1, lt blue is medium 2, and the other black tan is for high.

Jan 15, 2013 | 1999 Jeep Grand Cherokee

1 Answer

I need a wiring diagram for the blower motor on a 1999 jeep grand cherokee limited. I have two wires sticking out of the blower motor and I don't know where they go


Usually you have to splice the wires into the old plug.
You might be able to find a diagram on the websites for auto parts stores such as autozone.

Jul 06, 2012 | 1999 Jeep Grand Cherokee

1 Answer

How to change blower motor in. 99 grand Cherokee


Check this procedure...Blower Motor Resistor and Controller Replacement


REMOVAL

1. Disconnect and isolate the batten' negative cable.

2. Depress locking tab and unplug the wire harness connector from the blower motor

resistor or controller (power module).

3. Depress locking tab and unplug the resistor or controller connector from the blower

motor.

4. Remove the 2 screws that secure the blower motor resistor or controller to the

heater-AC housing.

5. Remove the blower motor resistor or controller from the heater AC housing.


INSTALLATION

1. Install the blower motor resistor or controller to the heater AC housing. The

housing is indexed to allow (controller power module) mounting in only one

position. Tighten the mounting screws to 2.2 Nm(20 in. Lbs.).

2. Plug in the wire harness connector to the blower motor resistor or controller.

3. Plug in the connector from the blower motor resistor or controller to the blower

motor.

4. Connect the batten' negative cable.

zjlimited_1958.jpg


Hope this helps (rerember to rating this and leave a testiomonial).

Sep 30, 2011 | 1999 Jeep Grand Cherokee

1 Answer

How do i change blower motor resistor on 99 jeep grand cherokee


Welcome to FIxYa.com



Blower Motor Resistor and Controller Replacement

Image Blower Motor Resistor Or Controller/Power Module Remove/Install

REMOVAL

1. Disconnect and isolate the batten' negative cable.

2. Depress locking tab and unplug the wire harness connector from the blower motor

resistor or controller (power module).

3. Depress locking tab and unplug the resistor or controller connector from the blower

motor.

4. Remove the 2 screws that secure the blower motor resistor or controller to the

heater-AC housing.

5. Remove the blower motor resistor or controller from the heater AC housing.

INSTALLATION

1. Install the blower motor resistor or controller to the heater AC housing. The

housing is indexed to allow (controller power module) mounting in only one

position. Tighten the mounting screws to 2.2 Nm(20 in. Lbs.).

2. Plug in the wire harness connector to the blower motor resistor or controller.

3. Plug in the connector from the blower motor resistor or controller to the blower

motor.

4. Connect the batten' negative cable.

leedavidian_45.jpg



Thank you for using FixYa.com

Regards, Lee Davidian

Nov 22, 2010 | 1999 Jeep Grand Cherokee

1 Answer

1999 jeep grand Cherokee Laredo a/c electric fan not turning on.I've already replaced the relay, it worked for a very short time then it won't work again, water thermostat also has been change, no help.


There is a resistor mounted by the fan, this could have burned out. Look on passenger side right by fan motor should be 2 screews that have 5-6 wires pluged into it had to replace mine once fan only on high worth looking in too. Also, check if the blower motor Resistor Harness was faulty.

Good luck.

May 21, 2010 | 1999 Jeep Grand Cherokee

1 Answer

1999 jeep grand cherokee heater fan quit. 40amp fuse under hood good. both wires at motor test hot. motor turns strong when wired direct to battery. now what?


the blower motor resistor is bad replace it and it will work good as new the resistor is located in the same heater box as the blower motor mounted on the outside of the heater box follow the wirring from the blower motor to find it or just simply buy the part and match it up

Jan 11, 2010 | 1999 Jeep Grand Cherokee

1 Answer

Blower motor resistor replacement


how do the wires go on a 2002 jeep grand cherokee blower motor resister.

Oct 18, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Ac blower won't work. Resistor has been replaced 3 times. I think it is the problem now. Is it easy to replace? Where is it?


Blower motor resistors are found on the pasenger side ducts near the blower motor. It should have three wires going to it.

Apr 22, 2009 | 2000 Jeep Grand Cherokee

1 Answer

99 jeep grand cherokee Blower Motor will not stop running ATC


You need to replace the switch which turns your fan speed up and down

Jan 30, 2009 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...