Question about 2001 Oldsmobile Aurora

2 Answers

Ground Splice Pack Location, 2001, 3.5

Recently grounded BLK wire from AC Clutch which solved a no AC operation problem. The BLK wire should have been at ground through Splice Pack SP100, Where is the SP100 physically located?

I also have erratic AT operation and left and right brake light inop. If the AC Clutch is not seeing ground thru SP100, perhaps there are other operational impacts, as well.....Thaks for your help.

Posted by on

Ad

2 Answers

That ground is located on the lower left front of the engine, near the trans. connector.
See this site for more info..
http://www.greatautohelp.com/more_oldsmobile_questions.html

Posted on Nov 01, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I'm not sure where the Splice Pack SP100 is but I can tell you what grounds fixed my AC problem.

I have a 2001 Aurora. The first two times I had intermittent air conditioning problems it was two different ground wires that needed to be re-attached. You can find the ground wires by taking off the shroud underneath the front portion of the engine. There are two bolts that screw into the engine. They can be taken out with a 15 mm wrench. I had to put new ends on the ground wires.

Posted on Sep 17, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2006 Jeep Liberty ac not working,fuses are fine,relay good replaced low and high pressure switches refrigerant level is good still won't work


Check for battery voltage on the dark blue/yellow wire in the connector at the AC clutch with engine running and AC on. If no voltage, yank the AC relay and check for battery voltage on terminal 86 in the relay socket. If no battery voltage on that terminal, check fuse 21. If yes, check for ground on terminal 85 in the socket. If no ground, then PCM isn't commanding the AC clutch on. Check for voltage on the dark blue/yellow wire at the low pressure switch and good ground on the black wire. The PCM provides power to the low pressure switch which then goes to ground. The PCM is looking for a large voltage drop if pressure is above 34-38 psi. If pressure is below that, the switch will be open, so the PCM won't see a voltage drop and will prevent AC clutch operation. The high pressure switch should be closed at pressures below 270-330 psi

Nov 30, 2017 | Jeep Cars & Trucks

1 Answer

2003 Pontiac aztek. What are the three connections for on the ignition module


B+ voltage supply , ground , crankshaft position sensor B input , IC timing control , IC timing signal , low ref. engine speed signal , etc... Do you know what these are ?
Ignition Control Module (ICM) -- C1
Connector Part Information
• 12162261
• 6 Way- F Metri-Pack 150.2 Series (BLK)
Pin
Wire Color
Circuit No.
Function
A
TAN/BLK
424
IC Timing Signal
B
WHT
423
IC Timing Control
C-D
--
--
Not Used
E
PPL/WHT
430
Low Resolution Engine Speed Signal
F
RED/BLK
453
Low Reference
Ignition Control Module (ICM) -- C2
Connector Part Information
• 12162184
• 2 Way-F Metri-Pack 150.2 Series Sealed Pull To Seat (BLK)
Pin
Wire Color
Circuit No.
Function
A
YEL
573
CKP Sensor 1 Signal
C
PPL
574
Low Reference
Ignition Control Module (ICM) -- C3
Connector Part Information
• 12162194
• 2-Way F Metri-Pack 150.2 Series Sealed (BLK)
Pin
Wire Color
Circuit No.
Function
A
BLK/WHT
51
Ground
B
PNK/BLK
239
Ignition 1 Voltage

Nov 07, 2017 | Pontiac Cars & Trucks

1 Answer

Where is the parking light relay located


No relay for the parking lights .
When the headlamp switch is moved to the PARK or ON position, battery voltage is supplied from the 15A Park Lamp fuse to circuit 9. Current flows through circuit 9 to the instrument panel fuse block (IPFB). Battery power passes through the IPFB to both license lamps, both front and rear tail lamps, both front park/turn lamps, and all marker lamps through circuit 9. The front marker and front park/turn lamps are grounded by circuit 150 through the forward lamp ground splice pack. The rear tail lamps and license lamps are grounded by circuit 550 at the rear ground splice pack and the right rear body ground.

Sep 18, 2015 | 2001 Saturn SL

3 Answers

Need color code on new connector


Just did my fuel pump on the 2001 isuzu rodeo. Well here is what you need to do about the different wire colors. First disconnect your negative battery. Drop the fuel tank and replace pump. Remember to have a splice kit in hand. Ok now here is how you connect the different colored wires. Black goes with black. Gray goes with black and orange wire. Purple goes wit blue and yellow. And the last wires goes together. I hope this helps.

Aug 12, 2012 | 2001 Isuzu Rodeo

1 Answer

When turn head lights on left turn indactor comes on and when head lights are off and use turn signal ac pannel flashes


You have a bad ground. Your A/C panel and your left turn indicator share the same ground. It is ground G401. It is a splice pack located at the left kick panel. You may have to disassemble the splice pack and clean corrosion from the connectors. (See picture for location)


dttech_201.gif

Sep 16, 2011 | 1994 Honda Civic

1 Answer

2001 GMC Sierra 1500 - When i turn lights on the driver side low beam works fins but the high beam is dim - both headlights high/low on passenger side are dim. When i put full beams on the drivers side on...


Sounds like a gound problem to me. Check you headlamp grounds. The ground circuits for your headlamps actually go through the underhood fuse block, then to the headlamp switch, then through Splice Pack #SP203 (Located under the left side of the dash it is bolted to the left "A" pillar) , then to ground #G200. (Which is actually the bolt that is holding the splice pack.) I have seen corrosion in the splice packs several times. You may want to disassemble it and clean the terminals. A LIGHT coat of dielectric grease usually works pretty good to prevent it from doing it again.

May 01, 2011 | GMC Sierra 1500 Cars & Trucks

2 Answers

I'm getting juice to the washer fluid pump but it doesn't run. I bypass the wiring harness and hook it directly to the battery and the pump runs. When I put a test light on it I'm getting juice to the...


For the circuit to operate, it must have both battery voltage and ground. If there is battery voltage at the connector, then hook your test light to the Positive side of the battery and check for ground on the opposite (Black) wire. The washer pump grounds at ground # G-201. It is located behind the right sie of the glove box. There is also a splice in this ground circuit. It is located inside the main instrument panel wiring harness about 7 inches from where the harness breaks out and goes to the radio connections. (It could be a bad/loose splice)

Jan 29, 2011 | 2001 Buick Regal

3 Answers

Chevrolet 2001 express van brake lights go out when headlights are turned on.


The first thing you should check is the ground. In the rear ov the vehicle on the left side of the back door you should see a ground wire connected by a green screw. (it may be a grey screw). let me know what you find.

Roy

Oct 23, 2009 | 2001 Chevrolet Express

1 Answer

I have a 1999 pontiac grand am and the reverse lights and brake lights work but i can not get the tail lights to work. I discovered that the reverse light on the bottom of the car is missing the connector...


Pin
Wire Color
Circuit No.
Function
A
BRN
9
Parklamp Feed
B
LT GRN
24
Backup Lamp Feed
C
BLK
750
Ground
Pin
Wire Color
Circuit No.
Function
A
BRN
9
Parklamp Feed
B
LT GRN
24
Backup Lamp Feed
C
BLK
750
Ground
Pin
Wire Color
Circuit No.
Function
A
BRN
9
Parklamp Feed
B
LT GRN
24
Backup Lamp Feed
C
BLK
750
Ground
Find 3 wire connector going to lense in trunk Pin
Wire Color
Circuit No.
Function
A
BRN
9
Parklamp Feed
B
LT GRN
24
Backup Lamp Feed
C
BLK
750
Ground
Pin
Wire Color
Circuit No.
Function
A
BRN
9
Parklamp Feed
B
LT GRN
24
Backup Lamp Feed
C
BLK
750
Ground
brown wire light green wire & black blk is grd moke sure its good, lit grn back up lights,drk Pin
Wire Color
Circuit No.
Function
A
BRN
9
Parklamp Feed
B
LT GRN
24
Backup Lamp Feed
C
BLK
750
Ground
brn tail lights turn parking lights on & with a test light back probe connector no power to brown? ck fuse trace harness to switch wires all good bad switch if you know how to use ohm meter you could use that to ck for shorts on continuity Pin
Wire Color
Circuit No.
Function
A
BRN
9
Parklamp Feed
B
LT GRN
24
Backup Lamp Feed
C
BLK
750
Ground

Aug 30, 2009 | 1999 Pontiac Grand Am GT

Not finding what you are looking for?
2001 Oldsmobile Aurora Logo

Related Topics:

415 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...