Question about 2000 Chevrolet Blazer

2 Answers

Power Seats I have a 2000 Blazer we just got and the power seats which have the memory, heat and lumbar worked great. Our son put a new motor in it and now the seats don't work. The manual doesn't give you much help as to if it is a fuse or what. Any ideas or idea of where to look to resolve? I havent been able to drive it yet cause the seats won't move and i'm short HA. Thanks for your help

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 958 Answers

You did not mention why did you replaced the motor at first.

but electric motor would run if you have power and switching. so what you have to test are;

do you have power going to the seats before the switch.
next does your switch are ok to transfer the power to the motor?
then check if trhe power is going to the motor but the motor does not turn..
the motor could have been installed incorrect..

let me know what u found out..

i hope i was able to help and fix it..

tnx

drcool



Posted on Jul 26, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 19,396 Answers

It is circuit breaker not afuse, it should be located where the relays are, possibly under the glove box.

Posted on Jul 26, 2008

  • Ginko
    Ginko Jul 26, 2008

    Try also disconnecting the battery for 1 minute and reconnecting, as sometime the circut breaker gets jammed.

  • Ginko
    Ginko Jul 26, 2008

    The the circuit breaker for the seats must return 30A if tested, it is located in thefuse box and should be indicated.There is here is a also a seat module that needs to be tested and it is located under the drivers seat, this can only be tested with a scanner. You should have tested all this compunents before replacing the motor, if the mor had not been tested it could have been OK.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the location of the power seat circuit breaker on a 2001 s10 blazer lt?


I think that more than likely wher eit draws the power in the fuse box the circuit feed to the fuse is burnt out ,this is often a strip on the back of the fuse box that runs across the frrd to the fuses so check for a feed in the fuse box on the fuse for the power seat

Oct 21, 2014 | 2001 Chevrolet Blazer

1 Answer

2000 Gmc jimmy power lumbar works but seat does not, can't find the exact fuse for seat?


IF THE LUMBAR IS WORKING, THE POWER IS THERE . IF EVERYTHING IS PLUGGED IN UNDER THE SEAT, THE SEAT MOTOR MAY BE FAULTY

Nov 19, 2010 | 2000 GMC Jimmy

1 Answer

Power seat controls are not working


First of all, check under the seat where there should be a cluster of wires. Sometimes if the power seat is used alot by sliding back and forth, without this cluster of wires being secured, occassionally a wire can get cut.
The runners on which the seats move are metal and cut wires easily. Secondly, the plug also located under the seat could have gotten wet or accidently came unplugged from someones feet in the back or objects and debris.
Another possibilty that will keep power seats from working is the power seat motor. In most cases, this small electrical motor is located directly under the power seat control panel or very nearby
Also you could check the fuses in the fuse box, located directly above the driver's left foot area. Power seats are usually on thier own circuit which means if the power seat fuse is blown, that is the only malfunction that will be noticed, versus other circuit which have many power items on one circuit. For example dash light, clock, and temp lights don't work, one fuse will fix the problem. Power seats operate on one fuse circuit which could have one or more fuses depending on the options of your seats. E.g. heated or not, lumbar, etc.

Mar 20, 2010 | 2005 Ford Expedition

1 Answer

Both electric front seats will not move the Lumbar and heat work


wire harness under the drivers floor gets wet and after time he splice for power to the seat starts to corrode and the splice breaks it is the Orange wire if you fix splice the seats should work

Oct 09, 2009 | 2000 Chevrolet Blazer

1 Answer

Seat will not move forward or backward...


if motor seemed to slowly get worse over time then there is a great chance that the motor is gone. You will have to unplug the motor and test for power at the motors connector. if the power is good when switch is activated then the motor is dead, but if no power is found then you either have a bad switch or connector or a wiring harness problem. It will not be the fuses since the driver and passenger seats are the same. also one more thing to check is if your vehicle has memory seats then if no power is found at motor, this memory module mounted to seat could be the problem..

Aug 22, 2009 | 2004 GMC Envoy

1 Answer

2000 Buick Park Avennue. Looking for advice on


Most probably the gear or cable broke.

Jun 07, 2009 | 2000 Buick Park Avenue

1 Answer

2000 GMC Jimmy Power seat stopped working


Left side of the dash, to the right of the IP fuse block. Its a 25 amp circuit breaker, an aluminum cased breaker. CHECK FOR POWER ON THE SEAT SWITCH "A" TERMINAL AND GROUND ON THE "D" TERMINAL. IF YOU HAVE POWER AND GROUND THE SWITCH IS BAD.

May 27, 2009 | 2000 GMC Jimmy

1 Answer

Need to replace driver light grey leather power seat - where to go.


I AM NOT GOOD WITH UPHOLSTERY BUT I BUY ON EBAY ONCE IN A WHILE AND I FOUND A GOOD UPHOLSTERY GUY THAT YOU CAN GET THIS SEAT OR JUST THE BOTTOM FROM IF YOU NEED IT .. I HAD HIM DO ME ONE FOR MY LEATHER SUBURBAN AND WOW ITS NICE AND I PUT IT ON EASILY THE HARD PART WAS TAKING THE SEAT OUT THEN FOUND OUT IT WAS A SNAP TO PUT ON .. THE GUYS NAME ON EBAY IS upholsteryguyss.gif IF YOU NEED ANY HELP WITH THIS LET ME KNOW YOU WILL BE IMPRESSED WITH HIS WORK.. AS FAR AS THE HEATED SEATS AND THE LUMBAR GOES YOU MIGHT FIND THE PROBLEM WHEN YOU GET IT APPART PUTTING ON THE COVERS .. USUALLY THEY GET BAD CONNECTIONS AFTER A WHILE.. THANKS JERRY AND HOLLER IF YOU NEED MORE.

Apr 20, 2009 | 2004 Chevrolet Silverado 2500HD

1 Answer

2000 Blazer power seats


i dont thing there is something to do with the power seats when you blew an engine, plus the power locks too.

im thingking, when you put the engine, a lot of wires and fuse boxes are in the engine compartment, you could probably disconnect some wire that are on the way on changing the engine and forgot to put the wires back together.

that is the only thing i could think of..

i hope i answered your questions...

tnx

drcool

pls rate me...

Jul 26, 2008 | 2000 Chevrolet Blazer

Not finding what you are looking for?
2000 Chevrolet Blazer Logo

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...