Question about 2002 Volkswagen Jetta TDI

2 Answers

Steps t0 change engine oil - 2002 Volkswagen Jetta TDI

Posted by on

  • Anonymous Sep 07, 2008

    where is the oil pan?

  • dddhubbard Sep 21, 2008

    change oil in 2006 New Beetle 2.5L

×

2 Answers

Remove protective bottom plastic cover under engine to gain acces to oil pan plug at the back of oil pan. Remove oil pan plug, drain old oil; replace oil filter. Replace plug and fill with oil. Replace plastice guard ubder engine.

Posted on Oct 17, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Here is a photo illustrated article:

Oil Change Instruction for Beginners - DIY Engine Oil Change for you Car

Posted on Jan 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Check engine light as well as the check gages light and the oil pressure gage has dropped to zero. I can shut of the engine and restart and everything is fine until I give it gas.


No magic bullet fix for the issue you are having. You will need to proceed step-by-step to diagnose the issue. Begin by changing the oil filter and the oil, as simply draining the oil from the oil pan may release whatever debris is clogging the oil pickup.
If your engine ran dry on oil, or if oil stopped circulating, and you tried to run the engine anyway, you may have done permanent damage to the engine, necessitating a complete overhaul. You can judge this by the condition of the oil when you change it.

May 18, 2015 | 2008 Dodge Ram 2500

Tip

How to change the oil in your car


Attention: Read each step completely before you begin that task. Tools Required:
#1: Oil filter wrench or pliers
#2: Small wrench and sockets (Metric sizes for import cars)
#3: Oil collection device (pan or bucket)
#4: Funnel
#5: Cloth rag or paper towels
#6: Jack and stands or ramps
Supplies Required:
-Correct amount and type of oil, and thrust washer if necessary
-Correct oil filter
Step 1: Determine the correct oil type, oil filter type and size, and amount of motor oil for your car. (Information found in owner's manual)
Step 2: Park your car on level ground and turn off the engine.
Step 3: Locate the engine and make the oil pan accessible. (With the use of jack and stands or ramps) Tool #6 required.
kormega_11.jpg
Step 4: Remove oil cap. (Located on top on engine)
kormega_12.jpg
Step 5: Loosen oil drain plug. Collect oil when draining and dispose of properly. (Located on oil pan which is attached to the bottom of engine block, directly below oil cap)
Tool #2and 3 required
Caution: Oil will start to drain and may be hot
kormega_13.jpg
Step 6: Once completely drained (a slow drip), replace oil plug. Install new thrust washer with oil drain plug if necessary. Do not over tighten.
Tool #2 required
kormega_14.jpg Step 7: Loosen oil filter. Collect oil when draining and dispose of properly. (Attached to the side or bottom of engine)
Tool # 1 and 3 required
Caution: Oil will start to drain and may be hot
kormega_15.jpg Step 8: Install new oil filter hand tight. Lube the rubber O-ring on oil filter with motor oil, and make sure the O-ring from the old filter is not still on the oil filter connector.
kormega_16.jpgkormega_17.jpg Step 9: Pour correct amount of new motor oil into engine.
Tool#4 required
kormega_0.png Step 10: Check for oil leaks from drain plug or oil filter.
kormega_18.jpg Step 11: Turn on engine and continue to check for leaks. Tighten oil drain plug or oil filter if necessary.
Step 12: Turn off engine and check oil dip stick to see if the right amount of oil has been added. After removing oil dip stick, wipe clean with rag or paper towel. Reinstall oil dip stick and then remove again to see correct oil level. Then Reinstall oil dip stick again.
Tool #5 required
kormega_19.jpgkormega_20.jpg Step 13: Lower vehicle from jack and stands or ramps.
Step 14: Record the mileage of the car for future reference. (Motor oil should be replaced about every 3 months or 3,000 miles)kormega_21.jpg

on May 03, 2011 | Nissan Maxima Cars & Trucks

1 Answer

How to do an engine oil change for 1994 acura integra?


omg are you serious? if you are not capable of doing an oil change i highly doubt you are able to remove the oil pan. best to let the mechanic change your oil, i don't want to give you step by step instructions knowing theres a possibility the vehicle may drop on your head due to your inexperience. btw your b16 or b18 engine holds 4.0 quarts of oil.

Aug 29, 2014 | 1994 Acura Integra

1 Answer

Reset change oil light


Driver Information Center (DIC) Equipped

Step 1 of 5

Place the key in the ignition and then turn it to the On/ACC position with the engine off.

Step 2 of 5

Press the "mode" button on the DIC until "Oil Life Left/Hold Set to Reset" is displayed on the DIC screen.

Step 3 of 5

Press the "set" button and hold it down until "100%" is displayed on the DIC display screen.

Step 4 of 5

Wait until three brief chimes emit before turning the ignition key back to the off position.

Step 5 of 5

Start the engine of the Aztec to ensure the oil warning light ("Change Engine Oil") is no longer illuminated on the instrument panel. If it still is, repeat the procedure.

Non-DIC (Manual Change Oil Light)

Step 1 of 4

Insert the key into the ignition and turn it to the ON/ACC position with the engine off.

Step 2 of 4

Step on the accelerator pedal fully to the floor three times within five seconds.

Step 3 of 4

Turn the ignition key to the off position.

Step 4 of 4

Start the engine to ensure the oil warning light is no longer illuminated on the instrument panel. If it is,repeat the procedure.

Aug 22, 2013 | 2003 Pontiac Aztek

1 Answer

"Engine Oil Level Fault" on


THERE IS A SOLUTION IN YOUR MANUAL SOMTHING LIKE PUT KEY IN START POSITOIN AN PUSH GAS PEDDLE TO THE FLOOR 5 OR 10 TIMES.

Jul 30, 2011 | 1997 Oldsmobile Aurora

1 Answer

Type of oil for engine how to change


Here is a step by step pictorial on how to change your oil in a Mazda3. Use 5w20 oil.



http://robert.aitchison.org/tiki-page.php?pageName=Mazda3+DIY+Oil+Change

Jan 30, 2011 | 2009 Mazda MAZDA3

1 Answer

How do i clear the change engine oil soon message. It's a 2007 silverado.


The "Change Oil" message displayed on your Chevrolet Silverado's gauge cluster is part of the Oil Life Monitoring System, standard on many GM (General Motors) vehicles. The message appears when it's time for an oil-change; the interval is based on your driving habits (for example, it may appear more frequently if you engage in a lot of stop-and-go traffic). Once you change your Chevy's oil, the message will not disappear; the system must be reset. The process is a bit different between Chevy Silverado models.
jQuery('.intro .thumbnail').each(function(i,e){ jQuery(e).find('img').one('error',function(){ jQuery(e).remove(); }); }); Difficulty: Moderately Easy Instructions
    2007 to 2010 Chevrolet Silverado
  1. Step 1 Insert your key and turn the ignition to position "C" (Run/On) without starting the engine.
  2. Step 2 Press the second button from the top on your information center (next to the steering column, car symbol) until "Oil Life" displays on your odometer cluster.
  3. Step 3 Press and hold the "Reset" button on your information center (check mark symbol) until the "Oil Life" display changes to 100 percent.
  4. Step 4 Turn your ignition to position "A" (Lock/Off).
  5. 2002 to 2006 Chevrolet Silverado
  6. Step 1 Insert your key into the ignition, and turn it to position "A" (Run/On) without cranking the engine.
  7. Step 2 Depress the gas pedal three times within five seconds. The "Change Oil" message will begin to flash.
  8. Step 3 Turn the ignition to position "A" (Lock/Off) once the light stops flashing (about 10 seconds).

Jul 12, 2010 | 2007 Chevrolet Silverado 1500HD

2 Answers

1995 buick century-oil light came on hour after oil change


Step 1-- replace the sending unit again. Step 2--if step 1 does not cure the problem--believe the light--have the oil pressure checked with a real pressure gauge temporarily installed inplace of the sending unit. Try to not run the engine at all until this is resolved. Usually a 1 min. run at idel with no oil pressure will not damage the engine. 5 min of idle will ruin it. 1 minute of highway speed 50 MPH cruise will destroy the bearings.

Jun 19, 2009 | 1992 Acura Integra Hatchback

2 Answers

How do you change the oil filter on a Hyundai Accent 1998/99?


Replace the oil filter after draining the old oil, and" BEFORE "adding new fresh oil, otherwise you'll be dump all that fresh oil, on the ground,while you "TRY to get the new filter installed.

Step 1 Remove drain plug,Drain oil into drain pan
Step 2 Remove oil filter
Step 3 Reinstall drain plug,qnce oil has drained.
Step 4 Fill new filter with oil,lube seal on filter.
Step 5 Install new filter, Add fresh oil to proper level.replace filler cap
Step 6 Run engine check for leaks.
Happy motoring!

May 23, 2008 | 1999 Hyundai Accent

Not finding what you are looking for?
2002 Volkswagen Jetta TDI Logo

1,734 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60867 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...