Question about 1998 Dodge Dakota

1 Answer

O2 Sensor for Dodge dakota 98

So if I replace the O2 sensor (can I do that myself) the problem will be solved or do I need to readjust the timing.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

You could replace the sensor yourself but you'd need a diognostic computer to clear the error codes from your car's ecm or you'll continue to have the problem even after you replace the sensor. A lot of the mobile mechanics have these diognostic computers with their tools.

Posted on Jul 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 dodge Dakota 4.7l. High mileage. OBDII throwing a new code everytime I fix something. Crank sensor & Cam sensor - replaced. IAC-replaced. PCM-replaced. Throttle body cleaned. O2...


Have you checked the wiring that goes to both the Crank and Cam sensors? Most of the time the wires are close to a heat source (ie: exhaust manifold) and the plastic covering starts to melt causing the cooper on wires to make contact and thus making engine stop, you will have to take off the protective covering as well as tape around the wires and inspect each and every one. Had same problem with Dodge caravan, it turns out the Crank Sensor plug wires were melted together. Good Luck.

Oct 26, 2013 | 1993 Dodge Dakota

1 Answer

P 0051 on dodge dakota trouble code


Bank 2 sensor 1 oxygen sensor heat circuit low. Look for broken wires or corrosion on connecter to the upstream O2 sensor on passenger side. If no apparent breaks or corrosion replace that oxygen sensor.

Mar 21, 2011 | 2001 Dodge Dakota

1 Answer

O2 sensors how to replace in 2002 dodge dakota 3.9


all you need is a 7/8 wrench. the o2 sensors are located in the exhaust system. just un plug them and unscrew them. not that hard to do if doing it for the first time.

Mar 30, 2010 | 2002 Dodge Dakota Club Cab

1 Answer

I need help on a 98 dodge dakota speedo wont work


What is the code that you have? The speed sensor and speedometer is all electrical. So the problem must be electrical. You may have a bad "new" sensor also, it doesn't happen much but sometimes these things don't work out of the box.

Mar 02, 2010 | 1998 Dodge Dakota

1 Answer

My dodge Dakota has a bad o2 sensor on it. It has 4 of these sensors, 2 on each side. How do I determine which one is bad?I did have the check engine code read on it so I do know it is an O2 sensor.


Hi:
I am pretty sure each O2 Sensor has it's own code.
If you have the code scanned again, it will tell you which one it is, bank 1 or bank 2 . before or after the Cat.

Nov 22, 2009 | 2001 Dodge Dakota

1 Answer

I have a dodge Dakota 2002 4.7 liter I have a fault code that reads p0155 do you know what that is? thanks Ron


O2 Sensor Heater Failure Oxygen sensor heater element malfunction solution replace the oxygen most likely the one located in the cat. converter make sure the replacement is original equipment(oe)

Sep 26, 2009 | 2002 Dodge Dakota Club Cab

1 Answer

On a 2004 Dodge Dakota V-6 3.7 , 5 speed. what is the number of O2 sensors ?


YOU HAVE 4 O2 SENSORS. YOU HAVE 2 PASSENGER SIDE.ONE O2 SENSOR ON EXHAUST MANIFOLD THE OTHER ONE AFTER THE CATALYTIC CONVERTER.YOU HAVE 2 ON DRIVERS SIDE.ONE O2 SENSOR ON EXHAUST MANIFOLD.THE OTHER O2 SENSOR AFTER THE CATALYTIC CONVERTER.

Sep 08, 2009 | 2004 Dodge Dakota

1 Answer

When I go to start my 2001 dodge dakota it just clicks. I checked


As far as the O2 sensor goes you should probably replace both. But the CEL should have given you a code to know which O2 sensor was acting up. In my experience it is almost alway the one before the Cat converter. As far as the clicking...Check your battery and see if enough power is getting to the starter. You can have it tested at an auto parts store or just try to jump it. If it jumps, you need to charge or replace your battery if it won't charge. If the battery is good however, you probably need to replace the starter. Good luck and thanks for using FixYa!

Jun 28, 2009 | 2001 Dodge Dakota

4 Answers

Dakota 4.7 P0161 code? What does it mean


P0161 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 2)
check the wiring to the bank 2 sensor, that is the one behind the catalytic converter on the opposite side from the bank where #1 cylinder is located, see firing order diagram below.
a92549a.gif

Apr 30, 2009 | Dodge Dakota Cars & Trucks

Not finding what you are looking for?
1998 Dodge Dakota Logo

Related Topics:

542 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...