Question about 2001 Dodge Neon

1 Answer

Speaker Replacement I have a 2001 Dodge Neon and the speaker blew on the driver side front door. How do I remove the door panel to replace the speaker?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 96 Answers

There should be at least 2 screws that are hiden in the door panel. One around the arm rest and the other down by the light/reflector.
Take those out and the panel should lift up. Becareful there will be a ton of wires that are attached to the door. Disconnect each of these and the panel will be free to remove.
You should have access to the speaker at this time.

Posted on Jul 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My drivers side front speaker stopped working in my 2003 dodge ram pickup


remove the speaker from drivers side , put that speaker in passengers side , if works in passenger side then speaker is o.k and if not speaker is stuffed if working wiring problem in drivers door or from stereo head unit .

Mar 28, 2014 | Dodge Ram 1500 Cars & Trucks

1 Answer

2001 dodge ram left front speaker not working


Check your wires but static could be if you ran your twelve volt amp wire and your stereo to amp wire on same side.

Apr 14, 2013 | 2001 Dodge Ram 3500 Truck

1 Answer

How do i take off de door panel of 2001 dodge intrepid


PHILLIPS SCREW DRIVER AND A DOOR PANEL REMOVER TOOL WORKS BEST,ONCE YOU REMOVE ALL SCREWS YOU CAN SEE I BELIEVE THE ARE SOME HIDDEN BEHIND THE SPEAKER GRILL ,TAKE THAT OFF AND THEIR SHOULD BE AT LEAST 3 AROUND THE SPEAKER AREA.ALOT OF PEOPLE DONT SEE THOSE.THEN GET THE DOOR PANEL TOOL PUT UNDER THE DOOR PANEL AND PRY IT TO YOU, MAY HAVE TO USE SOME FORCE THEIR PLASTIC SNAPS. THIER ALL AROUND THE DOOR.....HOPE THIS HELPS

Aug 04, 2011 | 2001 Dodge Intrepid

1 Answer

Need instructions to replace the passenger side mirror and the driver side tail light on a 1999 Ford Taurus 4-door sedan. Thank you, Gary S.


Section 01-09: Mirrors, Rear View 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Mirror, Power-Outside Rear View Removal
  1. Disconnect battery ground cable (14301).
  1. Remove front door trim panel (23942). Refer to Section 01-05.
  1. Remove radio speaker grille from cover assembly by squeezing or pinching between thumb and index finger.
  1. Remove two screws from cover assembly.
  1. Disconnect outside rearview mirror wiring connector (C515-LH; C615-RH). Remove wiring guides as necessary.
  1. Remove three outside rear view mirror retaining nuts. Remove outside rear view mirror (17682) while guiding wiring and connector through hole in door.


an0786b.gif


Item Part Number Description 1 17682 Outside Rear View Mirror 2 N621906-S36 Nut (3 Req'd) 3 F8DB-17D699-
AAW Cover Assembly Rear Substrate-LH 3 F8DB-17D698-
AAW Cover Assembly Rear Substrate-RH 4 N808968 Screw 5 F8DB-18B984-
AAW Speaker Grille-Standard (No Badge)-LH 5 F8DB-18985-
AAW Speaker Grille-Standard (No Badge)-RH 5 F8DB-18K901-
BAW Speaker Grille-Mach-LH 5 F8DB-18978-
BAW Speaker Grille-Mach-RH 5 F8DB-238A35-
AAW Speaker Grille-Blank (No Speaker)-LH 5 F8DB-238A34-
AAW Speaker Grille-Blank (No Speaker)-RH A - Tighten to 6-8 Nm (54-70 lb-in) ------------------
Trim Panel, Door Front
Removal
  1. Remove cover behind inside door handle.
  1. Remove screw from bottom of pull cup retaining front door trim panel to front door (20124).
  1. Remove three screws retaining front door trim panel to front door.
  1. NOTE: Do not attempt to remove more than one pushpin at a time.

    Using Rotunda Windshield and Molding Trim Removal Kit 107-R0401 or equivalent, remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin.
  1. Disconnect electrical connectors as necessary. Refer to Section 01-14A.
Installation
  1. Follow removal procedure in reverse order.
  1. Replace all pushpins with new pushpins (N808994-S).
Front Door Trim Panel


ar0318d.gif

Jan 14, 2011 | 1999 Ford Taurus

1 Answer

Power window failure, 1998 jetta vr6 glx, driver side does not work and passenger side only goes down from drivers switch. also how does the trim panel come off to work on the door


Remove the little door nob thingy for lock and unlock it just screws off,, Then you have 6 Allen key bolts around the door trim, remove those. Then remove the door handle cover just pops off you may need a small flat blade screw driver. you have two big screws Philips head screws in there... Then remove your speaker cover then the speaker, then remove the speaker, then remove the speaker bracket, then lift the door panel out. The motors and the regulators for your windows are **** door man makes a good unit for them i replace all 4 of mine... They are expensive Partsgeek.com is the best price i could fine. Looked for 2 years in junk yards and posted adds for replacement parts don't wast your time its damn near impossible. cost me about 500 for the 2 front window motors and regulators and I only replaced the regulators on the back windows I think they were about 50 a peace.

Jun 28, 2010 | 1998 Volkswagen Jetta

1 Answer

How do I replace speakers on a 1994 xj6 ?


Replacement of Front and Rear Door Speakers

Required Tools:

#2 Phillips Screwdriver (magnetic tip is useful)
9 mm Nut Driver
8” or 10” Flat Tip Screwdriver
Small awl or other sharp pointed instrument
Soldering Iron w/solder or 8 to 10 small wire **** splices
8 to 10 small machine screws -- #8 x ¾” or equivalent 8 to 10 small machine screw nuts & flat washers to match
Thread locking compound “Loctite” (optional)
6” wooden dowel of ½” diameter to be used as a drift
Small mallet or hammer

1) Whenever you are attempting to a remove door panel to gain access to the speaker, or any other electrical component, absolutely disconnect the negative battery cable. Battery power is supplied to each door window motor and it’s always prudent to de-energize these circuits before you attempt any panel work.

2) XJ40 door inner panels (front or rear) are comprised of an upper and lower section, which interface to provide complete inner door coverage. Neither panel is difficult to remove nor are any specialized tools required.


3) Remove the Upper Inner Door Panels as follows:

It’s a good idea to store all the removed parts and screws in the adjacent foot well for safekeeping and easy access when you are putting everything back together.

a) Using a small awl (or equivalent), remove the small “square” plastic cover for the inner door lock release mechanism (upper right side when facing inner side of door). It pivots towards the front of the car.

b) Using the #2 Phillips screwdriver, remove the inner door lock release mechanism plastic / chrome escutcheon. It’s held in place by a single machine screw. Pull out on the door lock release mechanism and the escutcheon is easily removed.

c) Using both hands, pull out on the wood veneer panel at the inner door lock release mechanism to provide clearance and slide the panel towards the front of the car. The panel is secured on the left side by slip-in clips and they release easily.

d) Using the #2 Phillips screwdriver, remove the two sheet metal screws on the left side. For the front doors only, lift the bottom of the rubber ventilation boot at the front edge of the door and remove the sheet metal screw. Additionally, for the front door only, use the large flat screwdriver as a lever to ease out the single “fir tree” type press-fit connector. Neither of the rear doors contains these two additional fasteners.

e) Using both hands, lift the upper inner door panel until it releases from the metal ridge along the window line. It doesn’t take much effort to remove the upper panel as it slides off vertically. Store it on the seats for safekeeping.

4) Remove the Lower Inner Door Panels as follows:

a) Using the #2 Phillips screwdriver, remove the sheet metal screw located at the upper edge of the lower panel.

b) Using a ½”small wooden dowel or equivalent drift, place it under the lower edge of the door handle screw access cover. Lightly tap each end of the access cover using the dowel and mallet in an upward direction to release the access cover. These covers can be tight if they have never been removed in the past, but they will release.

c) Using the #2 Phillips screwdriver, remove the sheet metal screw located in the middle of the door handle.

d) Using a small awl or equivalent, remove the bottom door light lens by releasing it from its locator at the rear and sliding it outwards from the door.

e) Using the #2 Phillips screwdriver, remove the lower panel securing sheet metal screw located in the middle of the bottom door light assembly. All sheet metal screw fasteners for the lower panel are now removed.

f) Using both hands (and the large flat screwdriver, if needed), carefully pull off the lower inner door panel by release the series of fir-tree type press-fit connectors along the sides and lower perimeter. Once the panel is removed, it can be laid horizontally on the seat as there is sufficient length of wire bundle to allow this movement. It is not necessary to disconnect the wiring harness, but if desired, the connectors can be released so that the panel can be moved to another more worker friendly location.

5) Remove Door Mounted Speaker as follows:

a) Disconnect the speaker positive and negative conductors by releasing the electrical connector.

b) Using the 9mm Nutdriver, remove the speed clip nut from each of the four (4) speaker fastener studs. Press the nutdriver down firmly to engage the speed nut … do NOT cut away any foam material as it is not necessary.

c) Using the #2 Phillips screwdriver, remove the sheet metal screw immediately to the left (driver side) or right (passenger side) of the speaker as viewed from the back side of the door lower inner panel.

d) Using the #2 Phillips screwdriver, remove the sheet metal screw immediately above the speaker. It is located just below the upper sheet metal screw securing tab on the lower panel … the screw was previously removed in Step 4a.

e) Using the #2 Phillips screwdriver, remove the sheet metal screw immediately to the lower right (driver side) or lower left (passenger side) of the speaker as viewed from the back side of the door lower inner panel.

f) Using the #2 Phillips screwdriver, remove the sheet metal screw immediately to the lower far right (driver side) or lower far left (passenger side) of the speaker as viewed from the back side of the door lower inner panel.

g) Steps 5c, d, e and f will release the speaker / window lift pushbutton panel from the lower door inner panel. Removal of the sheet metal screws will allow the speaker panel to be pulled away from the lower panel by 3” to 4” to facilitate access for speaker removal.

h) With the speaker / window lift pushbutton panel eased back for working clearance, grasp the speaker with one hand while pressing the four (4) speaker studs downward through the foam supporting material. After the studs are clear from the foam material, the speaker can be removed from the panel.

6) Install New Door Mounted Speaker as follows:

Typically, base XJ40 models use 3.5” door speakers while the VDPs will use 4” door speakers. Though I believe it is possible to mount either type in either model.

a) Using the wiring supplied with the new speakers and insulated solderless **** splices, transfer the old speaker wiring electrical connector to the new speaker. Another alternate method is to simply solder the old speaker wires with connector to the new speaker terminals. This is a superior method for electrical continuity and strength of joint … although it does require some soldering skills.

b) Install the new 3.5” speaker by easing back the speaker panel and sliding in the new speaker. Normally, the 3.5” models will mount with only two fasteners.

c) Using two of the small machine screws with flat washers, place these fasteners through the speaker mounting lugs and press them up through the existing holes in the foam supporting material. Secure the screws with flat washers and matching nuts from the back side of the inner door panel. The use of thread locking compound (Loctite) is a nice touch to prevent loosening due to vibration.

d) Re-install the sheet metal screws removed in Steps 5c, d, e and f. This will re-mount the speaker panel. Don’t forget to re-connect the speaker wire connector at the door panel.


7) Re-installation of the inner door lower and upper panels is literally a reverse of the removal procedure. No hidden tricks.

8) Perform Steps 3 through 6 for the other doors and the job is complete.

9) Remove Rear Footwell Mounted Speaker as follows:

This sequence is good for both 4” and 5.25” footwell mounted woofers.

a) Using a small flat screwdriver as a lever, carefully ease off the grill.

b) Using a #2 Phillips screwdriver, remove the four (4) sheet metal mounting screws.

c) Ease out the old speaker and release the electrical connector for the speaker wires.

d) Transfer the old speaker wires and electrical connector to the new speaker using solderless **** splices or by soldering the old leads to the new speaker terminals.

e) Re-connect the speaker wires to the harness by joining the electrical connector.

f) Mount the new speaker and re-attach the necessary sheet metal screws.

g) Press the speaker grill into place.

h) Repeat Steps 9a though 9g for the other footwell speaker.

Mar 10, 2010 | 1994 Jaguar XJ6

1 Answer

How to remove the inside door panel from a dodge 2005 2500 pick up


FRONT DOOR TRIM PANEL - REMOVAL
Release door latch and open door.
Roll window down.
Remove window crank Window Crank - Typical , if equipped.
Remove screws attaching trim panel to door Door Trim Panel and Trim Panel Screw
CAUTION: Do not forcibly pull trim panel from door, damage to trim panel may occur.

Simultaneously lift upward and outward to release retainer steps from inner door panel Trim Panel Retainer
Disengage inside handle linkage rod from inside handle.
Disconnect speaker harness wire connector Speaker And Power Mirror Connector
Disengage power mirror wire connector, if equipped (driver's side only) Speaker And Power Mirror Connector
Disengage clips attaching power window/lock switch panel to door trim panel. Disengage wire connector from switch panel, if equipped Power Door Lock/Window Connector
Separate door trim panel from vehicle.
INSTALLATION
Position trim panel at door.
Engage wire connector for window/lock switch panel, if equipped. Engage clips attaching power window/lock switch panel to door trim panel.
Engage power mirror wire connector, if equipped.
Connect speaker harness wire connector.
Engage inside handle linkage rod to inside handle.
Align trim panel retainer steps with inner door panel and slide trim panel into place.
Install screws attaching trim panel to door.
Install window crank, if equipped.

Hope helped with this; remember rated this help. Good luck.

Nov 12, 2009 | 2005 Dodge Ram 2500 Truck

1 Answer

Replace driver side mirror on 2001 Nissan Quest


SECTION 501-09: Rear View Mirrors 2001 Villager Workshop Manual REMOVAL AND INSTALLATION Mirror —Exterior Rear View Removal
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
  1. Remove the upper speaker.
    1. Disconnect the electrical connector.
    1. Remove the bolts.
    1. Remove the speaker.
  1. Position the watershield aside.
  1. Remove the exterior rear view mirror access panel.
  1. Disconnect the exterior rear view mirror electrical connectors.
    • Release the wiring harness locator.
  1. Remove the exterior rear view mirror.
    • Remove the bolts.
    • Feed the wiring harness through the door opening.

Mar 31, 2009 | 2001 Nissan Quest

1 Answer

2001 Mercury Sable Drivers side view mirror removal


No you do not, there will be a small plastic cover over the door mounted tweeter.

Squeeze it with your fingers and you should be able to pop it right off.

There are two screws on the speaker and the others should be visible on removal of the speaker itself.

I suggest you bring a soldering iron or a pair of wire cutters because the speaker wiring is soldered on the speaker and the speaker will not fall back through the speaker frame.

Jan 15, 2009 | 2001 Mercury Sable

2 Answers

Audi 2001 Speaker


Nope - this site isn't a sales site, it's just a tech advice site on how to fix problems. Your best bet for buying a speaker would be eBay, a salvage yard like www.shokan.com, or the classifieds sections on www.audiforums.com or www.audizine.com.

Jul 21, 2008 | 2001 Audi A4

Not finding what you are looking for?
2001 Dodge Neon Logo

200 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...