Question about Toyota Pickup

1 Answer

Windshield washer jet not aimed correctly - Pickup Toyota Cars & Trucks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 76 Answers

You could get a sewing nedle and insert it into the jet and aim it doing that this will also clean any gunk out but dont use one thats a tight fit as it could force any gunk further into the jet causing it not to work at all so be a little carefull doing this.

Posted on Jul 25, 2008

2 Suggested Answers

  • 150 Answers

SOURCE: windshield washer adjusting for 2003 ford escape

Best way is to use a pin and move the jets(fluid squirters) to the required position.try moving them initially and keep operating the washers and moving them until the desired position is attained

Posted on Mar 20, 2009

  • 96 Answers

SOURCE: 2002 Camry XLE. windshield washer

Have you tried using a pin, and inserting it in the hole of the nozzle to adjust it?? May be a little stiff, a small amount of penetrating fluid may help.

Let me know if this helps, and please rate this solution. Thanks

Posted on Dec 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my windshield wipers running in the off position, it's like they are running in the intermittent position, but it's in the off position.


When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Schematic Reference: Wiper/Washer Schematics


1

Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Symptoms - Wiper/Washer Systems

2

  1. Turn the ignition ON.
  2. Turn the windshield wiper/washer switch OFF.
Are the windshield wipers always on?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

Disconnect the windshield wiper/washer switch connector.
Are the windshield wipers always on?
Go to Step 4 if yes
Go to Step 7 if no

4

  1. Disconnect the windshield wiper motor connector.
  2. Test the windshield wiper switch signal 1 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 5

5

Test the windshield wiper switch signal 2 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 6

6

Test the windshield wiper motor high speed circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 9

7

Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 8

8

Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement - On Vehicle in Steering Wheel and Column.
Is the repair complete?
Go to Step 11
--

9

Inspect for poor connections at the windshield wiper motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10

10

Replace the windshield wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the repair complete?
Go to Step 11
--

11

Operate the system in order to verify the repair.
Did you correct the condition?
The Wiper / Washer System consists of the following components:
?€¢
Windshield wiper / washer switch


?€¢
Windshield wiper system module / motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
Instrument panel cluster (IPC)


?€¢
ACC 15-amp fuse


?€¢
WSW 30-amp fuse

Jan 04, 2016 | 2002 Pontiac Bonneville

1 Answer

Need to adjust windshield washer jets on a 2001 chevy prizm


Get a stick pin or sewing needle and stick in nozzle hole and adjust.

Feb 22, 2014 | Cars & Trucks

1 Answer

How do I adjust the windshield washer nozzles/


Just bend the nozzles up a little, without putting a kink in the line.

Jan 31, 2013 | 2011 Toyota Camry

1 Answer

The passenger side windshield squirter only sprays on the bottom of the windshield. The drivers side has 2 squirters, should the passenger side 2 also?


The washer jets are either full of car polish (if you polish it), or blocked with dirt from the washer fluid bottle. Blowing them with an air hose normally clears this out. You can then adjust the jet direction with a safety pin. Hope this helped...

Mar 05, 2011 | GMC Yukon XL Cars & Trucks

1 Answer

2002 Camry XLE. windshield washer aimed too low on windshield. tried to aim them up but they won't move.


Have you tried using a pin, and inserting it in the hole of the nozzle to adjust it?? May be a little stiff, a small amount of penetrating fluid may help.

Let me know if this helps, and please rate this solution. Thanks

Dec 17, 2010 | 2002 Toyota Camry

1 Answer

Windshield washer jets on my 92 Honda accord do not shoot windshield fluid out.


I would check the supply hoses to hood. I would also check the washer pump in the washer fluid bottle.

Nov 15, 2010 | Honda Accord Cars & Trucks

2 Answers

My windshield washer pump works,but no fluid on


Those little nubs on your hood or the spray jets on the wipers those spray jets need to be adjusted and be pointed up you can use a sewing needle just don't jam them or break them.

Jan 15, 2010 | 1995 Buick Regal

1 Answer

Windshield washer adjusting for 2003 ford escape


Best way is to use a pin and move the jets(fluid squirters) to the required position.try moving them initially and keep operating the washers and moving them until the desired position is attained

Mar 20, 2009 | 2003 Ford Escape

1 Answer

Windshield wiper jet


Try celaning the tiny port of jet with adequate needle. Fact that "other one is working" tells that windshield washer pump is working and that fliud is present. That means - just some physical obstacle is preventing fluid flow.

Feb 20, 2009 | 2002 Saturn Sl

1 Answer

Windshield washer


Most likely the washer pump motor has failed, unless your washer jets are plugged...
The washer pumps are known as a common problem. Remove the washer bottle & examine the motor. Is it cracked anywhere? If so, the motor will not work. Also, sometimes the connector gets corroded. Make sure that it is clean. Hope this helps.

Sep 22, 2008 | 1995 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...