Question about BMW 325

1 Answer

Won't Shift into first gear I think it's my clutch

Posted by on

  • Anonymous Dec 03, 2008

    first gear won't engage sometimes

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have an A/T. when engine is hot, won't shift to 2nd gear.

Posted on Dec 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Manual trans won,t shift 87f150


When there is an issue with a manual gear box not working after a clutch replacement I am always suspicious that the clutch plate has been fitted the wrong way and the crank bolts are fowling on the cluch plate center . If the gear box was fine before and i now faulty I would go to what was done with the clutch. Also check that the clutck slave cylinder is working ok.

Feb 22, 2013 | 1987 Ford F 150

1 Answer

It won't shift into 3rd gear until i get to 50 mph everything else works great


transmission clutches bad for third gear operation. needs trans overhaul..

Jan 18, 2013 | 1996 Dodge Caravan

1 Answer

5-Speed transmission;Won't shift into gear.


If you can shift it with car off, but not with engine running, it is a clutch poroblem. Check the fluid level in the clutch master cylinder on the firewall next to the brake master cylinder. If it won't shift with engine off, either the shift linkage is binding, or there is an internal problem in the transmission.

Jan 15, 2013 | 1992 Daihatsu Rocky

2 Answers

My 1998 Ford Explorer Sport Manual Transmission won't shift into any gear


Then there is a serious problem with the clutch. turn the engine off and engage a gear and try and roll the truck, do it feel like it is in gear? if not the clutch is either defective or the transmission input shaft is broken

Oct 12, 2012 | Cars & Trucks

1 Answer

My 03 mustang won't down shift after shifting the


HI,
Search online..but it sounds like the 'synchros' in the transmission are going/gone.
Also, the clutch may be wearing out.

Td

Oct 01, 2012 | Cars & Trucks

1 Answer

My shift knob won't move


WITH INFO YOU ARE PROVIDING CLUTCH MIGHT NOT BE COMPLETELY DISENGUAGING CAUSING A STIFF OR DIFFICULT SHIFT. CHECK BY PUTTING VEHICLE ON FLAT GROUND ENGINE OFF. GET INTO 1ST GEAR. THEN PUSH IN CLUTCH AND START CAR WITH BRAKE OFF IF CAR STARTS ROLLING THEN CLUTCVH IS STILL TRYING TO GRAB. THEN ADJUST THE CLUTCH PER VEHICLE SPECS.

Jun 11, 2012 | 2004 Mazda RX-8

2 Answers

Pickup starts great, goes into all gears but won't move. It's like it is still in nutural.


Assuming the pickup is an automatic, check the transmission fluid. The #1 cause for transmission slippage is lack of Automatic Transmission Fluid.

If the pickup is a standard shift, the pin that connects the shift to the transmission has likely broken. You would still be able to shift from the inside but the gears won't engage. A bad clutch is also a possibility but you would have noticed a burning smell prior to the clutch giving out.

Dec 20, 2011 | Cars & Trucks

1 Answer

My 1998 Honda civic ex won't move but the motor


Have you just replaced the clutch? Taken out the transaxle, and put it back in? Are you sure transmission was in good condition before this? If so, review your procedure carefully to be sure you got it all back right.
Watch the slave cylinder while someone depresses clutch. You should see the little plunger move slightly out and move the clutch lever back. The lever moves the release bearing inside bell housing into contact with the pressure plate. If slave cylinder doesn't move at all, try bleeding again. The plunger has to move when clutch is engaged.
I'm not sure what you mean by "will shift but won't go into gear". You mean it's actually going into a gear position and car won't move? Or it won't go into any gear, period. As if you had no clutch?

Nov 06, 2011 | 1998 Honda Civic

3 Answers

Hard to shift my gears when car in cold.Won't even go out of neutral to 1st gear.Forget about going into reverse.


With the engine off, check your operation of the gear shift. If you can go in and out of the gears fine without the engine running, then you have a worn clutch disc that needs replaced. If the problem still exists then you either have low fluid/weak hydraulic system, or there is a problem with the syncro that may be adjusted.

Nov 02, 2011 | 2006 Ford Focus

1 Answer

Clutch is about 2yrs old.Have to pump clutch mostly in order to shift.It sometimes won't shift.But if I turn the truck off completely,it will shift into all gears.


Could be a bypassing clutch master or a leak in master, line or slave. Pumping pedal gets pressure up (just like your brakes) You can shift with engine off because nothing is spinning.

May 17, 2011 | 1997 Toyota Tacoma

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

593 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Fred Sops

Level 2 Expert

271 Answers

Al Clark

Level 2 Expert

290 Answers

Doberman

Level 2 Expert

246 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...