Question about 1992 Acura Legend

2 Answers

My security system continues to sound when you open up the locked door.

Posted by on

  • jeffers1734 Jan 28, 2009

    the alarm goes off when it wants and i dont have a door key how do i shut it off

×

2 Answers

I appreciate you helping but, we have already tried that solution and it worked for a while. Now the car justs blares the alarm and we can not turn it off without disconnecting the battery. HELP!!!!!

Posted on Sep 07, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi,
I have a 1992 Acura Legend. If the alarm goes off when you open the door when the alarm is set you may have to close the door and put the key in the door lock and turn it clockwise to turn the alarm off.

Posted on Sep 06, 2008

3 Suggested Answers

  • 1986 Answers

SOURCE: Rear back door will not work with central locking system

If it makes a sound, but doesn't unlock / lock, then it's most likely the linkage has seperated. If it doesn't make a sound, it's most likely the actuator for the lock has broken. you'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to pull off the seal in order to see inside the door

Posted on Aug 19, 2009

  • 1 Answer

SOURCE: No security system beep when vehicle is locked

check to see if your "interior cabin lights" fuse isnt blown it is a 15amp fuse one of the top two rows in your fuse box. i have a 2002 A4 avant and when that fuse blows my security beep doesnt make any sound but the doors lock.

Posted on Dec 19, 2008

  • 1986 Answers

SOURCE: PASSANGER DOOR LOCK WILL NOT LOCK ALL OTHER DOOR

You'll probably have to remove the door panel and look at the lock assembly. It sounds like one of the linkages may be broken or seizing...

Posted on Aug 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 ford expedition eddie bauer All the doors won't lock/unlock, just make a buzzing sound repeatedly. Also does this when shutting the vehicle off.


What makes a buzzing sound , the door lock actuators ? Or where do you hear the buzzing coming from if not at the doors ?
Power Lock
The power lock/unlock feature requests all of the vehicle doors, including the liftgate, be locked or unlocked upon a customer request from any interior door lock switch in the vehicle. The power door locking system functions independently of ignition status or vehicle speed. When the vehicle security module receives an unlock/lock command from any door lock control switch, the vehicle security module will activate relays internal to the module to supply the correct power and grounds for the door lock actuators.
Visual Inspection Chart Mechanical Electrical
  • Binding latches
  • Central junction box (CJB) fuse(s):
    • 5 (7.5A)
    • 30 (30A)
  • Circuitry
  • Relays
  • Remote transmitter
  • Keyless entry keypad
  • Vehicle security module

  1. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
  1. If the diagnostic tool does not power up, refer to the diagnostic tool manual.
    1. Carry out the diagnostic tool data link test. If the diagnostic tool responds with:
      • SCP, UBP or ISO; all elctrconic control unitw, no response/not equipped, refer to Section 418-00 .
      • No response, not equipped for vehicle security module, refer to Section 419-10 .
      • System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs, and carry out the self-test diagnostics for the vehicle security module.
    1. If the DTCs retrieved are related to the concern, go to the Vehicle Security Module Diagnostic Trouble Code (DTC) Index to continue diagnostics.
    1. If DTCs are retrieved that are not found in the following Vehicle Security Module Diagnostic Trouble Code (DTC) Index, refer to the Master Vehicle Security Module Diagnostic Trouble Code (DTC) Index in Section 419-10 .
    1. If no DTCs related to the concern are retrieved, proceed to the Symptom Chart to continue diagnostics.

Jan 13, 2016 | Ford Cars & Trucks

Tip

How to set & cancel theft deterrent system or how to set & cancel security...


Theft deterrent system (on some models)

Theft deterrent system is designed to deter vehicle theft. The system flashes the turn signal lights and turns on the interior light or the signal lights only (depending on the model), and sounds security horn and vehicle horn when it detects abnormalities such as follows:

• Any door or hood is forcibly opened.
• The batter terminal is disconnected and then reconnected
• The system control is disconnected and then reconnected.
• Abnormal impact is detected when the impact sensor function is on.

The system flashes the turn signal lights and turns the interior light or the signal lights only (depending on the model), and sounds security horn and vehicle horn if someone attempts to damage or break into your car.

Setting the system

You can set the system with or without the impact sensor function. For details, see "Canceling the impact sensor" below.

1. Turn the ignition key to "LOCK" and remove it.
2. Have all passengers get out of the vehicle
3. Push the lock (set) switch on the wireless remote control key once. At this time, the turn signal lights flashes once and the security indicator light comes on.

The system is set after 30 seconds. At this time, the security indicator light start flashing slowly.

Once the system is set, you cannot start the engine until you cancel the system.

The system will not be set in the following cases.

• When any of the door is open; security horn sounds for 1 second, close the door and set the system again.
• When the hood is open; close the hood securely.

Canceling the Impact Sensor

The impact sensor can be cancelled to prevent false alarms from being triggered incase of the following conditions:

• When parked in the noisy area
• The vehicle body or glass is subjected to a strong impact from the (such as in highly pressurized car wash).
• When transporting by a car carrier or ferry.

To cancel the impact sensor;

1. Lock the door by pushing the lock (set) switch on the wireless remote control key once, and turn signal light flash once
2. Then push the lock (set) switch twice within 5 seconds. At this time, the turn signal flash 5 times to indicate the impact sensor function is disable.

The impact sensor is deactivated as long as the system remained armed.

Canceling the system

The system will be cancelled by the following two ways:

• Turn the ignition key from "LOCK" to "ON" position.
• Unlock any of the doors by pushing the unlock (cancel) switch

If the turn signal lights flash 3 times, the system has been alarmed. Check to see if there is any abnormality with your vehicle.

If any of the doors is not opened within 30 seconds, all doors will be automatically locked and the system will be set.

When the system is set

Activating the system; When the system detects abnormalities such as follows, it flashes the turn signal lights and turns on the interior light or the turn lights only (depending on the model) and sounds the security horn and vehicle horn of 30 seconds.

• Unlocking any door without using wireless control
• Any door or hood is forcibly opened.
• The battery terminal is disconnected and then reconnected.
• The system control assembly is disconnected and then reconnected
• Abnormal impact is detected when the impact sensor function is on.

Reactivating the alarm;

Once set, the system automatically resets the alarm after the alarm stops.

The alarm will activate again under the same circumstances described in "Activating the system".

Stopping the Alarm

The alarm will be stopped by the following two ways;

• Turn the ignition key from the "LOCK" to "ON" position.
• Unlock any of the doors by pushing the unlock (cancel) switch.

The system can be cancelled by these ways at the same time.

If the battery becomes discharged due to the vehicle being unused, for a long time etc., when the battery is recharged or replaced, the system will activate the alarm. If this happens, immediately unlock any of the doors by pushing the unlock (cancel) switch, and the alarm will stop.

Testing the system

1. Set the system
2. Insert a wireless remote control key into the key hole on the driver's door handle, and unlock the door.
3. Open the door, and an alarm will sound.
4. Stop the alarm by pushing the unlock (cancel) switch.
5. Repeat this operation for the front passenger's door.

Good luck.

on Nov 08, 2010 | Toyota Pickup Cars & Trucks

1 Answer

When I put the key in door to unlock it locks and unlocks and continues this while I have the key in lock when I remove key it locks putting the security feature on.


You either have a bad "arm/disarm" switch or the switch has fallen off from the lock cylinder.

What is happening is the security system is not receiving the disarm signal when you unlock the door with the key. It thinks the car is being stolen so it continues to lock the lock to prevent this.

There arm/disarm switch is clipped onto the door lock cylinders on the front doors and the rear hatch. If it does the same thing with the other doors than there may be an issue with the security system. If the other doors work fine than I would pull the door panel (I assume you are getting this problem with the drivers front door) and inspect the switch.

Here's a pic of what it looks likeairjer995_92.jpg

If you have any questions let me know.

Oct 14, 2011 | 1998 Dodge Grand Caravan

1 Answer

Bought from dealer with no keyless entry. alarm activates when doors are locked with power doorlock system. alarm sounds when we open the door. how do we de-activate the alarm before unlocking the door?


Opening the drivers door with the key is supposed to shut down the factory security but the drivers key cylinder usually goes bad. You will have to unlock the rear tail gate lock cylinder with the key and that will shut down the factory security, before opening the drivers door.Your other option is to have an aftermarket keyless entry system installed, which will open the doors remotely while shut down the factory security at the same time.

Jan 25, 2011 | 1996 Jeep Grand Cherokee

2 Answers

Anti theft system came on dash. shut the car down will not start. 2002 cadillac. i was told 30 differ sensor showed wrong. which sensor to start with.


The SECURITY light is located on the instrument panel cluster.

If the ignition is off and any door is open, the SECURITY light will flash, reminding you to arm the system. To arm the system, do the following:
1. Open the door.
2. Lock the door using the power door lock switch with the door open or the remote keyless entry transmitter. The SECURITY light should come on and stay on.
3. Close all the doors. The SECURITY light should go off within approximately 30 seconds. If a door or a trunk is opened without a key or a remote keyless entry transmitter, the horn will sound and the lamps will flash for about 30 seconds.

Also can check this and other details in the 2002 Cadillac Owners Manual (page 85 and next).

Hope helps (remember rated and comment this).

Jun 15, 2010 | 2000 Cadillac DeVille

2 Answers

(driver)door switch does not work properly dash shows doors open when all doors secured. alarm system dbl beeps interior lts stay on. attempts to reset alarm system failed.


this car has door lock switches attached to every door lock inside the door,try lubricating fluid in the lock mechanism first but if it fails you will have to remove each door panel, unplug the door switch jump it with a paper clip and this door being the only one open see it light goes out continue this until you find which door is the problem and replace that lock.

Jan 26, 2010 | 2002 Mercury Sable

1 Answer

I have the code for my 2002 land rover discovery i just dont know how to put it in, any ideas thanks


To enter the EKA:
Close all the doors.
Turn the key in the driver door lock to the unlock position and hold there for at least 5 seconds until the alarm sounds once. Then return to centre - always ensure you return to centre and do not delay more than 10 seconds between turns, or hold in the position for more than 5 seconds or you will reset to the start. Turn to full extent of travel.
1st Digit turn to unlock the number of times specified.
2nd Digit turn to lock the number of times specified.
3rd Digit turn to unlock the number of times specified.
4th Digit turn to lock the number of times specified.
Finally turn to unlock once more. If it is correct a double bleep will sound (single bleep is incorrect code)
You now have a 5 minute delay - don't open any doors. The anti-theft indicator will continue flashing once every 2 seconds for the five minute period. When this goes out, open the door and start within 30secs.
After 3 failed attempts, the security system invokes a delay period of 10 mins during which the system will not accept any further attempts to enter a code.

Oct 19, 2009 | 2002 Land Rover Discovery Series II

1 Answer

No security system beep when vehicle is locked


check to see if your "interior cabin lights" fuse isnt blown it is a 15amp fuse one of the top two rows in your fuse box. i have a 2002 A4 avant and when that fuse blows my security beep doesnt make any sound but the doors lock.

Dec 02, 2008 | 2002 Audi A4

1 Answer

2002 saturn vue


sounds like a short in the security system wiring. i assume you have the locking system with the keyless entry? if so, you've got a short somewhere, most likely. take it to a good mom and pop electrical service place unless you've got a warranty at saturn. you'll get a cheaper price and often get better service.

Oct 25, 2008 | 2002 Saturn VUE

1 Answer

2002 Honda Odyssey security alarm system


Make sure your hood is shut. I just got my 2002 Honda Odyssey back from the dealer today (90,000 mile check-up - I love my van and will drive it until it dies!) and when I went to lock the van with my remote transmitter, the lights didn't flash and the horn didn't sound. I open and closed all the doors and tailgate and I could hear that the doors were locked, but the security system wasn't working and that is why the lights didn't blink or the horn didn't sound. I walked up to the front of the van to check the hood to make sure it was closed (there isn't an indicator light for an open hood, only open doors) and the hood wasn't shut completely. Once I opened the hood and let it drop to securely shut, I hit the door lock button on the remote and everything worked like a charm! Hope this helps others in this predicament.

Sep 12, 2008 | 2002 Honda Odyssey

Not finding what you are looking for?
1992 Acura Legend Logo

Related Topics:

503 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...