Question about 1996 Ford Explorer

1 Answer

Hydraulic clutch line disconnect - 1996 Ford Explorer

Posted by on

  • Anonymous Sep 27, 2008

    clutch cable disconnect



×

Ad

1 Answer

You can buy a line disconnect tool from local auto parts store

Posted on Oct 08, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 98 camaro v6 manual hydraulic clutch line keeps disconnecting itself


sounds like the lock on the line is bad or the lock on the slave cylinder is bad they make new broke stuff everday

Oct 18, 2017 | 1998 Chevrolet Camaro

1 Answer

How do you bleed the hydraulic clutch on 1984 944


924 has cable operated clutch. When the cable on mine broke pedal went straight to the floor, hydraulic usually much slower to get to floor. Cable is an easy replacement. bleeding hydraulic usually done from nipple on slave cylinder (near release arm on clutch housing.

Feb 01, 2018 | 1984 Porsche 944

1 Answer

How do you bleed the clutch


The clutch master cylinder, remote reservoir, slave cylinder and connecting lines are all serviced as an assembly. These components cannot be serviced separately. The linkage cylinders and connecting lines are sealed units. They are pre-filled with fluid during manufacture and must not be disassembled nor disconnected."Chrysler does not provide a procedure to bleed the clutch hydraulic system" .

Sep 24, 2011 | 1993 Dodge Dakota

1 Answer

How to replace 1989 gmc slave cilynder


Disconnect the negative battery cable.
raise the vehicle and support it safely.
disconnect the hydraulic line from the secondary cylinder.
disconnect the hydraulic line from the master cylinder.
on all models except the 1988-90 C/K series, remove the nut retaining the hydraulic line and the speedometer cable to the cowl, than install the nut to hold the speedometer cable in place.
cover all hydraulic line to prevent dirt and moisture from entering the system.
installation is the reverse of removal. bleed the clutch hydraulic system.....
Hope this helps ????

Jun 01, 2011 | GMC Sierra Cars & Trucks

1 Answer

Can't get pressure on my 94 hi-ace van after bleeding the clutch


Disconnect the hydraulic line to the clutch and see if you get pressuse when the pedal is pushed. if not you have a bad clutch cylinder.

Mar 11, 2011 | Toyota Pickup Cars & Trucks

1 Answer

Is the clutch slave cylinder internal or external of transmission?


external if it's like my 1979 Honda. Internal if like the following information:
Slave Cylinder on 1999 Chevrolet Cavalier
REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Detach the master cylinder assembly from the actuator cylinder by disconnecting the hydraulic line.
  3. Remove the transaxle assembly, as outlined earlier in this section.
  4. Remove the clutch actuator cylinder from the transaxle. Fig. 1: Clutch actuator cylinder assembly mounting 91147g02.gif
    To install:
  5. Lubricate the inside diameter of the bearing with clutch bearing lubricant GM part no. 12345777 or equivalent.
  6. Install the actuator cylinder in the transaxle, then install the transaxle assembly.
  7. Connect the master cylinder-to-actuator hydraulic line.
  8. Bleed the hydraulic system, as outlined later in this section.
  9. If removed, install the air intake duct.
  10. Connect the negative battery cable.
prev.gif next.gif

Jun 20, 2010 | 1999 Chevrolet Cavalier

2 Answers

How do you remove and old hydraulic line of a slave cylinder on a 1992 2WD 4.0L Cherokee so that the new one can be installed?


i dont think you are supposed to remove it. they come with a hose master and slave cyl all put together.
i did get one aprt once and i think there was a roll pin i pulled out to do it

Mar 20, 2010 | 1992 Jeep Cherokee Limited

1 Answer

Cant disconnect pushrod from clutch pedal to


have some push all the way down on the clutch than squeeze the plastic tabs on bushing to release u also need a special tool to remove disconnect the hydraulic line from clutch release cylinder most auto stores carry it or let u use /loan for free

Oct 31, 2009 | 2000 Chevrolet Silverado 1500

Not finding what you are looking for?
1996 Ford Explorer Logo

Related Topics:

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5677 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...