Question about 1995 Jaguar XJ6

1 Answer

Glove Box Good Afternoon, Are you talking about the center console? Or is it in another place? Thank you for your help

Posted by on

  • prodmgr2001 Jul 29, 2008

    Thank you for your help. That is what we thought but we did not know for sure.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Yes - behind the gear shift, in between the two front seats - where the driver would place his/her right arm while he/she is driving. I beleive that is the only "glove box" that the car has. That is all that my 1995 jag XJ6 has anyway. :-)

Posted on Jul 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need diagram for replacing heater core



    Detach the heater core hoses at the firewall. The two black hoses attach near the firewall on the passenger's side of the engine compartment. Squeeze the hose clamps on the end of the hoses with pliers and slide the hoses from the heater core tubes.

    • 4Remove the lower passenger's-side and driver's-side dashboard panels. The two panels are held in with push-pins. Raise the center of the push-pins with a small, standard screwdriver and pull the pins from the panels. Pull the panels away from the dashboard to separate them from the dashboard.
    • 5Remove the center console. Separate the gear select trim piece from the center console, using a small standard screwdriver to pry the trim piece from the center console. Lift it over the shift knob and rotate it to clear the knob. Remove the retaining screws holding the center console in place with a Phillips screwdriver. Lift the console up over the shift knob and remove it from the interior.
    • 6Remove the glove box. Open the door to the glove box. Squeeze the two retaining tabs on the ends of the glove box and pull the glove box away from the dashboard. Remove it from the interior.
    • 7Detach the drain tube from the heater core cover, which is located behind the glove box. The tube can be pulled from the heater core cover by hand. Detach the air intake duct from the bottom of the heater core cover. The air intake duct runs from the bottom of the cover to the center of the dashboard. Remove the duct by hand.
    • 8Remove the retaining screws on the black heater core cover with a Phillips screwdriver. Pull the cover from the heater core and remove it from the interior. Remove the heater core clamp screw with a Phillips screwdriver, pull the clamp away from the heater core, then pull the heater core from the housing.
    • 9Place the replacement heater core against the housing. Place the clamp over the heater core and install the clamp retaining screw with a Phillips screwdriver. Position the heater core cover over the heater core and install the retaining screws with a Phillips screwdriver.
    • 10Attach the drain tube and the air intake duct to the heater core cover.
    • 11Install the glove box. Squeeze the retaining tabs on the sides of the glove box and push it into position against the dashboard. Release the tabs when the glove box is in position.
    • 12Install the center console. Guide the console over the shift knob and install the retaining screws with a Phillips screwdriver. Slip the shift selector trim piece over the shift knob and push it into the center console.
    • 13Place the lower passenger's-side and driver's-side dashboard panel in position. Install the push-pins into the retaining holes, pushing the in center of the pin to engage the pins.
    • 14Fill the radiator with coolant. Most climates require a 50/50 mix of DEXCOOL coolant and water. 2.2L engines require 8.6 qts., 2.4L

Nov 22, 2012 | 2000 Oldsmobile Alero

1 Answer

HOW TO CHANGE THE IN CABIN FILTER ON A CHRYSLER 200


All of the older answers are incorrect. Open the glove box. Remove everything from the glove box and set it aside. On the right and left sides of the glove box, there are some rubber stoppers. Simply push inward on the sides of the glove box toward the center so that you can open the glove box beyond the point where the rubber stoppers stop it.

After opening the glove box all the way (past the rubber stoppers) look inside, just above the blower unit. There are arrows on the left and right end of a rectangular black cover. Push the release tabs which the arrows point to, and remove the cover. Pull the filter out.

Install the new filter, and put the cover back in place by snapping it on as you found it. Push the sides of the glove box toward the center, and close the glove box. Open it as you normally would, and put your stuff back in the glove box.

Sep 13, 2012 | 2009 Chrysler 300

1 Answer

I am trying to replace the fuel pump relay switch on a 1997 S-10 Blazer, 4WD, 4 door. Several forums on line say to look in the back of my glove box behind a plastic panel, however, I do not have a glove...


my S-10 has a fuse relay box under the hood (Square box about 6 inches with a thumbscrew
knob in the center) it's not too obvious with all the emissions junk in there. Hope this helps.

May 01, 2011 | 1997 Chevrolet Blazer

1 Answer

Where is the turn signal relay on a 2000 chevy blazer? im getting three diff answers.. thank you


I looked it up on Alldata and they have it on the passengers side behind the glove box.The other place I remember it being was behind the ashtray panel.Check the easy one first.Behind the glove box.Hope this helps.Good luck.

Nov 07, 2010 | Chevrolet Blazer Cars & Trucks

1 Answer

How do ypou change out the blow fan in a mercury villager 1999


There are 3 screws holding it in. But, you have to remove lower center console (4 attachments, 2 on each side), then remove center trim above console, then remove glove box, then remove 2 ft long steel brace beow glove box, then remove blower. 2 hour job. one screw is hidden by carpet, pull carpet outward for access.

May 29, 2010 | 1999 Mercury Villager

2 Answers

Where is the blend door?


It is behind the center console on the right side. You can see it through the glove box, upper left, with the glove box dropped down. These are from a Sedona with the dash removed. Know this will help someone!KIZ4K8
10_5_2011_9_46_49_pm.jpg
10_5_2011_9_47_31_pm.jpg

Dec 17, 2009 | 2002 Kia Sedona

2 Answers

How does glove box come off to replace air cabin filter ?


First, take a good look at what you’re doing.
Look on the right side of open glove box and locate a plastic lever. You will see grooves on the end connected to the glove box. The grooved area is the spot to place the thumb in order to press this lever off the glove box when it comes time to do that.
Look up under the glove box. You will see two brass colored screws one on each side of the bottom of the glove box. These screws go up through two square plastic hinges that are attached to the glove box and into the the dash frame.
Okay, with the glove box closed remove the two brass colored screws, and put them aside so you won’t lose them..
Open the glove box and hold the glove box with your left hand and press on the plastic lever (grooved area) located on the right side of the glove box. This lever (the lever already mentioned above) is slotted and will pop off the glove box.
Put the glove box carefully aside.
Look straight in behind the glove box. You will see a rectangular black plastic cover approximately 1.5 inches wide by 8 inches long. On the right and left side are arrows pointing in. Press the arrows and pull out on the cover. This will slide out the tray that holds the filter. Remove old filter and insert the new one, flow arrows pointing down.
Retrieve glove box, hold in place, and attach plastic plastic lever to the right side of the glove box. The reverse of removal.
Next, the two plastic hinges located on the bottom of the glove box fit underneath the dash frame.
While holding the glove box in place (the glove box latch may hold glove box in place while installing screws) re-install the two screws through the plastic hinges into the frame and tighten.
Hope this helps you.

Oct 30, 2009 | 2004 Honda Accord

1 Answer

Where is the ecu located


On most honda/acura the ecu is always under the passenger side mat under the glove box, its going to be on the left side near the center console. If its not there its been relocated and then it could be placed in the same place just on the driver side kick panel.

Oct 06, 2009 | 2001 Acura 3.2TL

1 Answer

How do i change the fan switch on a saab 900s 1989? can someone help me out here


Are you talking about the a/c fan/blower switch?
Remove the glove box and the panel from the side of the center console.
Remove air duct on floor and protective cover. Remove the 2 fan control unit retaining screws and unplug the connector. Hope this helps....if you did not mean the a/c fan/blower switch please re-post with more specific details.

Aug 29, 2009 | 1989 Saab 900 4 Door

1 Answer

How to install air conditioning filter? How to open glove compartment


Air conditioning filter doesn't exist. If you're talking about the HEPA filter, it is installed very carefully... To open the glove box, push the glove box button or pull the glove box lever .. whichever is apparent/appropriate. Otherwise, Go to http://www.hmaservice.com/ and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about your vehicle.
If this is not what you want, Take/tow the vehicle into a Hyundai Service Center (dealership), pay the diagnostic fee. They will tell you EXACTLY what the problem is and what's needed to fix it (parts, labor, tax, time-frame, etc.). In any case, if NONE of these options appeals to you... your option is as good as mine.

Jun 24, 2009 | 2000 Hyundai Sonata

Not finding what you are looking for?
1995 Jaguar XJ6 Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Raygin
Raygin

Level 2 Expert

322 Answers

yadayada
yadayada

Level 3 Expert

61037 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...