Question about Hyundai Sonata

1 Answer

Need to know how to install a crank shaft positon senson on a 2003 hyundai sonata with a 2.4 engin

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 96 Answers

The 2.4 i believe the sensor is under the front plastic cover that hides the belts at the bottom of the engine, if it is i wouldnt recommend doing it your self, most of them require you to remove the timing belt (which i do recommend replacing at that time) to replace the sensor which is not easy to do if you dont have all the tools and knowledge or experience doing them.

Posted on Aug 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Install crankshaft kit on 2004 hyundai sonata 6 cylinder 2.7l engine


Really need more information...It sounds like they didn't give you a complete gasket kit...You will have to remove and re-install other components just to be able to see the crank shaft....You need the front and rear oil seal for the crank..,Oil pan gasket..,exhaust will have to be removed also...etc.......NEED MORE INFO..

Jan 24, 2015 | Hyundai Motor 2004 Sonata

Tip

What you need to know about Hyundai


I am a mechanic ..most people ask questions about these foreign hyundai motors ..below is an example of engines that basically if you ask about a Hyundai Xg 350 ,xg300 ..well allow me to hammer 90% of your questions in case you want to grab another motor ..these motors listed will work on 90% of all hyundai products ...Look at the starter sizes ,,all the same for the selected models ..then look at the motor sizes ..This will help you in solving some problems most do not give the specific questioning
100% NEW REPLACEMENT STARTER
FOR
STARTER

12 VOLT / CW ROTATION / 8 TOOTH DRIVE

REPLACES:
MANDO M62957
VALEO TM000A14401
BOSCH REMAN SR4118X
BOSCH NEWMAN SR4118N
HYUNDAI 36100-37210

FITS ON:

HYUNDAI
2001 SANTA FE 2.7L ENGINE
2002 SANTA FE 2.7L ENGINE
2003 SANTA FE 2.7L ENGINE
2004 SANTA FE 2.7L ENGINE
2005 SANTA FE 2.7L ENGINE
2006 SANTA FE 2.7L ENGINE

2003 SANTA FE 3.5L ENGINE
2004 SANTA FE 3.5L ENGINE
2005 SANTA FE 3.5L ENGINE
2006 SANTA FE 3.5L ENGINE

2002 SONATA 2.7L ENGINE
2003 SONATA 2.7L ENGINE
2004 SONATA 2.7L ENGINE
2005 SONATA 2.7L ENGINE

1999 SONATA 2.5L ENGINE
2000 SONATA 2.5L ENGINE
2001 SONATA 2.5L ENGINE

2003-2008 TIBURON 2.7L ENGINE

2005-2008 TUCSON 2.7L ENGINE

2001 XG300 3.0L ENGINE

2002 XG350 3.5L ENGINE
2003 XG350 3.5L ENGINE
2004 XG350 3.5L ENGINE
2005 XG350 3.5L ENGINE

KIA
2004 AMANTI 3.5L ENGINE
2005 AMANTI 3.5L ENGINE
2006 AMANTI 3.5L ENGINE

2001 MAGENTIS 2.5L ENGINE

2002-2006 MAGENTIS 2.7L ENGINE

2001 OPTIMA 2.5L ENGINE

2002 OPTIMA 2.7L ENGINE
2003 OPTIMA 2.7L ENGINE
2004 OPTIMA 2.7L ENGINE
2005 OPTIMA 2.7L ENGINE
2006 OPTIMA 2.7L ENGINE

2002-2005 SEDONA 3.5L ENGINE

2005 SPORTAGE 2.7L ENGINE
2006 SPORTAGE 2.7L ENGINE
2007 SPORTAGE 2.7L ENGINE
2008 SPORTAGE 2.7L ENGINE

on Oct 24, 2013 | Hyundai Cars & Trucks

1 Answer

How to replace a 2003 Sonata Crankshaft sensor


It can be but it is a bear to do and you will need a full complement of tools & maybe someones' help.

Aug 31, 2014 | Hyundai Motor 2003 Sonata

1 Answer

WHERE IS THE SERPENTINE BELT LOCATED ON A 2003 HYUNDAI SONATA


Vehicles Covered: Hyundai Sonata 2002-2004 (2.4L & 2.7L Engines)

In 2003, Hyundai produced two types of Sonata:
Available engines:
4 Cylinders 2.4L VIN "S", MFI DOHC - see Figures 1 and 3.
6 Cylinders 2.7L VIN "H", MFI DOHC - see Figures 2 and 3.

To differentiate between these types of 2003 Hyundai Sonatas, the VIN 8th digit (Engine Type) will either be "S" or "H" as in the table above.

To locate the Engine drive belt, jack up the vehicle & place it onto jack stands, then slide under the car (toss a cardboard mat down first), then, once under the car, remove the (plastic) engine splash shield. Once removed, the drive & accessory belts are easily observed.

12_27_2011_5_25_29_am.jpg

Fig. 1 Accessory Drive Belt Routing 2.4L (4 cyl) Engine - Hyundai Sonata
The "COMPRESSOR" refers to the A/C compressor, and "GENERATOR" refers to the Alternator.


12_27_2011_5_27_01_am.jpg

Fig. 2 Accessory Drive Belt Routing 2.7L (6 cyl) Engine - Hyundai Sonata
The Belt Routing on the Left is "With A/C", on the Right is "without A/C"

Inspection - Drivebelt and Accessory Belts

Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. Worn or damaged drive belts should be replaced.

Drivebelt Removal & Installation - 2003 Sonata (2.4L and 2.7L engines)

Raise and support the vehicle.
Remove the engine splash shield.
Rotate the drive belt tensioner clockwise to release the drive belt tension.
Remove the drive belt from the alternator.
Slowly release the drive belt tensioner.
Remove the drive belt from the accessory drive pulleys.

To install:

Install the drive belt to the accessory drive pulley.
Rotate the drive belt tensioner clockwise.
Install the drive belt to the alternator.
Ensure the drive belt is properly aligned and seated into the grooves of the accessory drive pulleys.
Slowly release the drive belt tensioner
Install the engine splash shield.
Lower the vehicle.

Here's the best illustration I can find of the Hyundai 2.4L and 2.7L engines - the drivebelt seems to be located on the passenger side of both of these transversely mounted engines.

12_27_2011_6_03_16_am.gif

Fig. 3 Hyundai 2.4L and 2.7L engines - Underhood sensor locations 2002-2004 only

Glossary of Acronyms
---------------------------------
A/C - Air Conditioning
DOHC - Dual Overhead Cam
MFI - Multi-port Fuel Injection

Dec 25, 2011 | Hyundai Motor 2003 Sonata

2 Answers

Where is speed senor on a Hyundai Sonatas


Hyundai VSS locations:
On 1999-2003 vehicles, the vehicle speed sensor is built into the speedometer. On 2004-2005 vehicles, the vehicle speed sensor is attached to the output shaft of the transaxle.

On 1996-2003 vehicles, the vehicle speed sensor is built into the speedometer. On 2004-2005 vehicles, the vehicle speed sensor is attached to the output shaft of the transaxle.

On 1999-2003 vehicles, the vehicle speed sensor is built into the speedometer. On 2004-2005 vehicles, the vehicle speed sensor is attached to the output shaft of the transaxle.

Hope helps (remember rated this).

Jul 14, 2010 | Hyundai Motor 2004 Sonata

1 Answer

Hyundai Balance Shaft Bearing making noise?


Possible. It's hard to give you an accurate cause, since I'm not able
to hear the sound. Most of the time, when you hear a slight wrapping
sound, it's a rod bearing,or crank bearing. When the rod bearing goes,
you'll know it,since it will knock like an SOB.

Mar 25, 2010 | Hyundai Motor 2003 Sonata

1 Answer

I have a 2003 sonata, in july the alternator and battery went and now the crank shaft sensor went. are they related?


No not related, the battery and alternator can be related, but not the crank sensor.They are not on the same cicuit, just coincidence.

Oct 27, 2009 | 1992 Hyundai Sonata

2 Answers

2003 Hyundai Sonata vvvibbbrraattteess!!!!


There are Two Balance Shafts on the 2.4. Did your mechanic also change the balance shaft belt when he changed the timing belt? If he didn't, you'll want to do that. Since you mentioned the old belt was missing teeth, those loose teeth flying around could have damaged the crank position sensor and sensor blade (tone wheel). Also, the front balance shaft (on the side of the engine nearest the radiator), has THREE different positions when the timing mark is lined up - here's the glitch - ONLY ONE of them is the correct one - this is probably where your vibration is.

Oct 10, 2009 | Hyundai Motor 2003 Sonata

2 Answers

2003 hyundai sonata


I have the same problem, starting today. i was driving and it just died. and when its cold it cranks. but when hot itll start and instantly die.

Oct 28, 2008 | Hyundai Motor 2003 Sonata

1 Answer

Where is the crank position senson on a 2000 hynidai accent


One is inside the timing box near the bottom chaff balance belt. The other is on the drivers side of the engine.

Sep 11, 2008 | 2000 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...