Question about 1998 Toyota Sienna

2 Answers

Replace left front window regulator - 1998 Toyota Sienna

Posted by on

  • Anonymous Nov 01, 2008

    It's going down alone

  • buckeyemax Nov 29, 2008

    It seems that only the dealer can order the front left window regulator at nearly $500. Very frustrating. Junk yard may have one.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Link to replace the window motor and regulator.

http://wiki.answers.com/Q/How_to_replace_window_motor_for_a1999_sienna

-Viz

Posted on Jul 01, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You can get a replacement window regulator from many on-line parts warehouses, or at your local Kragen, Autozone, etc. Price for the regulator only (less motor) run between $65-$85, with the motor costing around the same price. I did find one place which had the regulator/motor combo for $75.

Here are a few on-line links:

1Aauto.com ( This is where I found the combo for $75)
PartsTrain.com
Car-Stuff.com

By the way, I am going to try to replace the same parts on my 1998 Sienna van. Any idea where I can download the procedures for free? Don't need the entire repair manual, just the information for replacing the regulator/motor.

Mojo

Posted on Feb 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2000 chevy s10 2wd. Where is the relay switch to my drivers side window. The window switch is and the motor is good. But cant find the relay switch to check it and see if it's bad.


Sorry but there is no relay switch ! Go to www.bbbind.com free wiring diagrams .Check it out ! Your regulator is probably bad ! Is there B+ voltage at the switch , at the motor ?
Left Front Window Switch Operation
Place the ignition switch in the RUN position in order to supply battery voltage to the left front door lock and side window switch through the POWER WINDOW circuit breaker and the CKT 1001 (DK GRN). Press the left front window UP switch in order to supply battery voltage to the left front side window regulator motor through CKT 164 (DK BLU). The window motor is grounded through CKT 165 (BRN) and the window switch DOWN contact.
The regulator motor runs to drive the window to the UP position. Press the DOWN window switch in order to provide battery voltage to the window regulator motor in the opposite direction through CKT 165 (BRN). The window regulator motor is grounded through the CKT 164 (DK BLU) and the window switch UP contact. The motor runs in order to drive the window down.

Aug 22, 2016 | Cars & Trucks

1 Answer

No power to the left front window 1996 honda crv


Motor works but window doesn't?

Remove the inner door panel & replace
the broken window regulator

Switch over motor to new one

No voltage to switch?

Some other issue?

Nov 24, 2012 | Cars & Trucks

1 Answer

I have a 2000 Cherokee sport 4 door, 4wd. The left windows work fine but the right front and rear do not work. The LED light on the switch itself is lit. I replaced the window regulator for the front left...


Take a door panel off on the right, and see if you have power and ground going to the regulator when you press the button. If you dont, then your going to be chasing wires

Mar 25, 2010 | 2000 Jeep Cherokee 2WD

1 Answer

Left front door window goes up crooket,plastic


unfortinatly the plastic piece you found is part of the regulator. more than likley the whole thing needs replacement. usually around 120 at the parts store

Feb 06, 2010 | 1997 Chevrolet Venture

1 Answer

Passenger window fails to go up the last 1/4 inch. How do I remove the interior door panel and what am I looking for? Michael


Hello Michael. I am surprised that your window continued to work well as long as it has. Most haven't. This is a common issue with 1999-2002 Sonatas. You'll either need to replace the regulator upper holder or the regulator itself.

Technical Service Bulletin (TSB) 02-80-001 provides very nice details for replacing either the regulator upper holder or the regulator itself. You can view the TSB at www.hmaservice.com (requires Internet Explorer) by signing up for a free account.

The part numbers are as follows:

left front holder: 82430-38000
right front holder: 82440-38000
left front regulator: 82403-38011
right front regulator: 82404-38011.

I copied the part numbers from the TSB. If memory serves, the regulator numbers ending in -38011 may have superseded to numbers ending in -38012.

Regards, Joe PS please rate my answer. Thank you Michael and happy holidays.

Dec 16, 2009 | 2000 Hyundai Sonata

1 Answer

Left front door window sometimes will not go back up! When I use either the left front door, window up/down switch, or the driver side up/down control, for the left front door, I can hear the switch...


USUALLY POWER WINDOW PROBLEMS ARE ONE OF THREE THINGS. 1. SWITCH 2. MOTOR 3. WINDOW REGULATOR. THE MOST COMMON PROBLEM THE LEXUS HAS IS THE MASTER SWITCH IN THE DRIVERS DOOR. IT CAN ALSO AFFECT THE OPERATION OF THE PASSENGER DOOR SWITCH....IF WINDOW REGULATOR IS BAD YOU WILL HEAR SOME CRAZY NOISES COMING OUT OF DOOR PANEL...VERY OBVIOUS.... FOLLOW THIS CLOSELY...STARE AT A LITE DOME LIGHT USUALLY WITH DOOR OPEN...WHEN YOU PRESS WINDOW SWITCH, IF THERE IS ANY DIMING OF DOME LIGHT....MOTOR IS BAD. IF DOME LIGHT STAYS THE SAME BRIGHTNESS... SWITCH IS BAD... EXCEPT IN THE CASE SOME HACKER HAS BEEN IN THE DOOR PANEL BEFORE ...IT DOES TAKE A SPECIAL TALENT TO REMOVE DOOR PANELS WITHOUT BREAKING THINGS AND EVEN MORE TALENT TO REPLACE WINDOW REGULATORS

Aug 21, 2009 | 2003 Lexus RX 300

1 Answer

I need to change out a broken window regulator on the left side front door


replacing the window regulator is pretty simple there is no need to go to a maual window all u have to do is take the door panel off and if u will go by the window regulator u can identify whick part u will need to remove and replace its a bolt on item and fairly simple to replace but the part is kinda pricey around 200-300 bucks but if u go to ebay u can buy one for around 80 -100 bucks good luck

Apr 18, 2009 | 1998 Ford Mustang

1 Answer

Power window problem. engauges then disenguages


Section 01-11: Glass, Frames and Mechanisms 1997 Windstar Workshop Manual REMOVAL AND INSTALLATION Door Glass and Regulator, Power Windows Removal
svw~us~en~file=ani_caut.gif~gen~ref.gif WARNING: IF THE REGULATOR COUNTERBALANCE SPRING MUST BE REMOVED OR REPLACED FOR ANY REASON, MAKE SURE THAT THE REGULATOR ARMS ARE IN A FIXED POSITION PRIOR TO REMOVAL TO PREVENT POSSIBLE INJURY DURING C-SPRING UNWIND.
  1. Remove front door trim panel (23942) and front door inside panel sound insulator (20394). Refer to Section 01-05 .
  1. Remove inside door belt weatherstrip.
  1. Remove front door window glass (21410) as described in this section.
  1. Remove two nut and washer assemblies attaching the window regulator equalizer arm bracket (23230).
  1. Remove four rivets retaining the front door window regulator base plate to door inner panel.
  1. Remove front door window regulator (23200) and front door window channel bracket (23288) from vehicle.
  1. Working on a bench, carefully bend tab flat to remove front door window regulator arm slides from front door window channel bracket.
  1. NOTE: Use care not to break tab; if tab is cracked or broken, replace front door window channel bracket. Make sure rubber bumper is installed properly on new front door window channel bracket, if replacement is made.

    Install new front door window regulator arm plastic guides into front door window channel bracket and bend tab back to 90 degrees.


    a9ef3ee.gif

Installation
NOTE: The front door window channel bracket and window regulator electric drive (23394) are installed into the vehicle as one assembly. The front door window channel bracket may be disassembled from the window regulator electric drive as described in Door Glass and Regulator, Power Windows .

  1. Install window regulator electric drive with preassembled front door window channel bracket into vehicle. Set the regulator base plate to door inner panel using base plate locator tab as a guide.
  1. NOTE: Two 1/4-20 x 1 inch bolts and two 1/4-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (35-44 lb-in). Equivalent metric retainers may be used.

    Install four rivets to retain front door window regulator to door inner panel.
  1. Install window regulator equalizer arm bracket.
  1. Lower front door window regulator arms to access holes in door inner panel. Install front door window glass as outlined.
  1. Install inside door belt weatherstrip.
  1. Adjust front door window glass to make sure it is properly aligned with glass run. Check window for smooth operation.
  1. Install front door trim panel and front door inside panel sound insulator. Refer to Section 01-05 .


    Door Glass and Regulator
ac1dac5.gif

Item Part Number Description 1 21410 Front Door Window Glass 2 23288 Front Door Window Channel Bracket 3 23394 Window Regulator Electric Drive 4 23230 Window Regulator Equalizer Arm Bracket 5 222A00 Front Door Glass Run Latch Side Retainer 6 N621906-S36 Nut and Washer 7 N800510-S36 Screw 8 23200 Front Door Window Regulator 9 W525172-S Rivet 10 W525175-S Rivet 11 — Wire Connector (Part of 14630 Wire Assembly) A — Tighten to 7-10 Nm (62-89 Lb-In)

Apr 13, 2009 | 1997 Ford Windstar

1 Answer

Replace a window regulator in a 1994 ford explorer


wow, a lot of work to do.

Window Regulator, Front Door, Explorer Removal
srk~us~en~file=ani_caut.gif~gen~ref.gif WARNING: IF THE REGULATOR COUNTERBALANCE SPRING MUST BE REMOVED OR REPLACED FOR ANY REASON, MAKE SURE THAT THE REGULATOR ARMS ARE IN A FIXED POSITION PRIOR TO REMOVAL TO PREVENT POSSIBLE INJURY DURING C-SPRING UNWIND.
  1. Remove front door trim panel and front door trim shield . Refer to Section 01-05B .
  1. Remove inside door belt weatherstrip and glass stabilizer.
  1. Remove front door window glass as described in this section.
  1. Remove two nut and washer assemblies attaching the equalizer bracket.
  1. Remove three rivets (manual) or four rivets (power) attaching the regulator base plate to front door trim panel finish panel (23712) .
  1. Remove window regulator electric drive and front door window channel bracket from vehicle.
  1. Working on a bench, carefully bend tab flat to remove arm slides from front door window channel bracket .
  1. Install new window regulator electric drive arm plastic guides into front door window channel bracket and bend tab back to 90 degrees. Use care not to break tab; if tab is cracked or broken, replace front door window channel bracket . Make sure rubber bumper is installed properly on new front door window channel bracket , if replacement is made.

    4a5a8fb.gif

Installation
NOTE: The front door window channel bracket and window regulator electric drive are installed into the vehicle as one assembly. The front door window channel bracket may be disassembled from the window regulator electric drive as described in Steps 7 and 8 of Window Regulator, Removal.
  1. Install front door trim panel finish panel with preassembled glass bracket into vehicle. Set the regulator base plate to window regulator electric drive using base plate locator tab as a guide.
  1. Install three (manual) or four (power) rivets (385189-S100) to attach regulator to front door trim panel finish panel . Two 1/4-20 x 1-inch bolts and two 1/4-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (3-5 ft-lb). Equivalent metric retainers may be used.
  1. Install equalizer bracket.
  1. Install inside door belt weatherstrip and glass stabilizer.
  1. Lower regulator arms to access holes in front door trim panel finish panel . Install front door window glass as outlined.
  1. Adjust glass to ensure proper alignment with glass run. Cycle glass for smooth operation.
  1. Install front door trim panel and front door trim shield . Refer to Section 01-05B .

Apr 11, 2009 | 1994 Ford Explorer Limited

1 Answer

2004 Mercury Monterey left frnt window sector gear R&R proceedure


are you a techie? You need a heavy duty riveter to do this repair. May have to rent or borrow from auto store.

here's the procedure



Front Door Trim Panel s4w~us~en~file=adobe.gif~gen~ref.gif Printable View (251 KB) NOTE: LH side is shown. RH side is similar.
  1. Remove the parts in the order indicated in the following illustration and table.

    df2877a.gif

  2. Item Part Number Description 1 23942/23943 Mirror access panel 2 1722897 Cup assembly 3 W56904-S424 Window regulator control switch panel screws 4 14A665 Window regulator control switch panel
    Removal Note 5 W701930-S424 Front door trim panel screw 6 W701930-S424 Front door trim panel screw 7 N602703-S61 Front door trim panel screw 8 1723943 Front door trim panel 9 W705590-S300 Nut insert(s)
  1. To install, reverse the removal procedure.
Item 4: Window Regulator Control Switch Panel Removal Note
  1. If equipped, disconnect the electrical connector(s).
-----------------------------------------------------------------------------------
Door Window Glass — Front s4w~us~en~file=adobe.gif~gen~ref.gif Printable View (328 KB)
Special Tool(s) s4w~us~en~file=st1132a.gif~gen~ref.gif Heavy Duty Riveter
501-D011 (D80L-23200-A)
  1. Remove the front door trim panel. For additional information, refer to Section 501-01 .
  1. Position the watershield aside.
  1. Remove the parts in the order indicated in the following illustration and table.

    To remove individual parts, only carry out the listed steps: Part Steps Front door window glass 1, 3 Front door window regulator 1-5 Front door glass run 1, 3, 6-8
    4be8135.gif
Item Part Number Description 1 W706495-5100 Rivet (2 required)
Removal Note
Installation Note 2 N8621986 Nut (3 required) 3 21410 Front door window glass 4 W706495-5100 Rivet (4 required)
Removal Note
Installation Note 5 23200 Front door window regulator
Removal Note 6 N800507-S Bolt (2 required) 7 21596 Front door glass run 8 — Front door glass run (Part of 21596)
  1. To install, reverse the removal procedure.
Item 1: Rivet Removal Note
  1. Connect the window control switch.
  1. Connect the battery.
  1. Position the door window glass halfway down to gain access to the door window glass rivets.
    • Remove the rivets.
9391398.gif Item 4: Rivet Removal Removal Note
  1. Remove the rivets.
Item 5: Front Door Window Regulator Removal Note
  1. Disconnect the electrical connector.
  1. s4w~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Prior to power window motor removal, make sure the regulator arms are in a fixed position to prevent counterbalance spring unwind. Failure to place the regulator arms in a fixed position can cause the spring to suddenly release resulting in personal injury.
    NOTE: The counterbalance spring assists the window in the upward direction.
    Remove the bolts and the window regulator motor.
Item 4: Rivet Installation Note
  1. Using the special tool, install the rivets.
b4c4793.gif

Feb 21, 2009 | 2004 Ford Freestar

Not finding what you are looking for?
1998 Toyota Sienna Logo

1,184 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

71288 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7009 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...