Question about 2000 Toyota Tundra

1 Answer

Water Pump Installation - 2000 Toyota Tundra

Posted by on

  • krackatinni Jul 29, 2008

    cant find the water pump position

  • Anonymous Aug 06, 2008

    what is required to remove the existing water pump on the 1990 toyota celica GT? What is required to get access to the water pump and how many bolts need to be removed? approximately how long does it take?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Buy a repair book at the auto store it has pictures fix pump and return book to auto store

Posted on Dec 03, 2008

  • assblurb Dec 03, 2008

    go buy a repair manual for your year and make and follow the step by step directions and pictures then return the book or go to a library and get one for free

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to replace my water pump in my Toyota Avalon. I need to know what parts I need and if I need to replace the timing chain as well


Hi Zachary,here's a link on replacing your water pump,your engine is a 3.5,the engine number is 2GR-FE,it also says you will need 2 special tools,if you buy the water pump from Autozone,they will loan you the tools,you will have to leave them a deposit,you get your money back when you return them,also you don't need to put a new timing belt on,as it says. Repair Guides Water Pump Removal Installation AutoZone com Here'a link to a new water pump. Repair Guides Water Pump Removal Installation AutoZone com Here's a link to some gasket sealer. AGS Thermostat and water pump RTV silicone gasket sealer TG 1A...

Sep 26, 2016 | 2006 Toyota Avalon

1 Answer

Serptine belt diagram


q4073a.gif



Belt Installation, Aerostar 4.0L Engine


q1815e.gif


Item Part Number Description 1 8620 Drive Belt 2 N606068 Bolt 3 10300 Generator 4 10153 Generator Mounting Bracket 5 8509 Water Pump Pulley 6 6B209 Drive Belt Tensioner 7 N800199 Screw 8 8678 Belt Idler Pulley 9 N802096 Screw 10 19703 A/C Compressor 11 2882 A/C Compressor Mounting Bracket 12 3C718 Brace 13 N806020 Bolt 14 3A674 Power Steering Pump 15 3A733 Power Steering Pump Pulley 16 N800199 Screw 17 N606572 Bolt 18 N620481 Nut 19 8501 Water Pump 20 6312 Crankshaft Pulley A - Belt Tension Check (See Specifications) B - Tighten to 40-55 Nm
(30-41 Lb-Ft) C - Tighten to 24-30 Nm
(18-23 Lb-Ft) D - Tighten to 21-29 Nm
(15-21 Lb-Ft) E - Tighten to 40-50 Nm
(30-37 Lb-Ft)

Belt Installation, Ranger and Explorer 4.0L Engine


q4082b.gif


Item Part Number Description 1 8620 Drive Belt 2 10300 Generator 3 8678 Belt Idler Pulley 4 19703 A/C Compressor 5 3A733 Power Steering Pump Pulley 6 8501 Water Pump 7 6312 Crankshaft Pulley 8 6B209 Drive Belt Tensioner 9 N806020 Bolt 10 2882 A/C Compressor Mounting Bracket 11 3A674 Power Steering Pump 12 N606572-S2 Bolt 13 N800199-S8M Bolt 14 N620481-S2 Nut 15 3C718 Brace 16 N606068 Bolt 17 10153 Generator Mounting Bracket 18 8509 Water Pump Pulley 19 N605805-S2 Bolt A - Belt Tension Check (See Specifications) B - Tighten to 21-29 Nm
(15-21 Lb-Ft) C - Tighten to 40-55 Nm
(30-41 Lb-Ft)

Belt Installation, Ranger 2.3L Engine


q3646c.gif


Item Part Number Description 1 8678 Belt Idler Pulley 2 10300 Generator 3 8509 Water Pump Pulley 4 3A733 Power Steering Pump Pulley 5 2E884 A/C Clutch Pulley 6 6312 Crankshaft Pulley

Belt Installation, Aerostar 3.0L Engine


q4740a.gif


Item Part Number Description 1 10300 Generator 2 3F671 Belt Idler Pulley 3 3A733 Power Steering Pump Pulley 4 6B209 Drive Belt Tensioner 5 6312 Crankshaft Pulley 6 8509 Water Pump Pulley 7 19703 A/C Compressor 2010&c18=modelyear&c35=wsm%2cdrive%20belt%20replacement%2cssk%2c03-05%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=405&ct=lan&hp=n&[aqe]

Mar 07, 2011 | 1995 Ford Aerostar

1 Answer

Steps on replacing a water pump 2001 ford explorer sport trac


4.6L Enginezjlimited_400.jpg

Fig. Water pump installation - 4.6L SOHC and DOHC engines

  1. Before servicing the vehicle, please familiarize yourself with safety procedures.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    Engine cooling fan Drive belt Water pump pulley Water pump
  4. Discard the O-ring seal.
To install:
  1. Installation is the reverse of the removal procedure.
  2. Install a new O-ring seal and lubricate with engine coolant.
  3. Observe the following tightening torques:
    Pump bolts 18 ft. lbs. (25 Nm). Pulley bolts 18 ft. lbs. (25 Nm).

Hope this helps (remember to rate this answr)

Jan 04, 2011 | Ford Explorer Sport Trac Cars & Trucks

1 Answer

How long does it take to change a water pump in a 2002 SL Saturn


Hi. Normal installation would take 45 to 1 hour depends on your expertise. Here's the procedure on how to replace the power pump.

  • TOOLS REQUIRED
  • J-43651 Water Pump Sprocket Holding Tool
REMOVAL



  1. Disconnect negative battery cable.
  2. Remove air inlet tube and air cleaner assembly. Refer to "Air Cleaner Assembly Removal".
  3. Drain coolant.


  1. Remove exhaust manifold heat shield. IMPORTANT: Twist water feed pipe while pulling to remove it from water pump.


  1. Remove thermostat and water feed assembly bolts.


  1. Remove water pump sprocket access plate from front cover.


  1. Install J-43651 water pump sprocket holding tool. IMPORTANT: Be sure to remove retaining bolt that is accessed from front of engine block.


  1. Remove water pump retaining bolts.
  2. Remove water pump assembly.
INSTALLATION

NOTICE: Prior to installing the water pump read the entire procedure. Pay special attention to avoid part damage and to ensure proper sealing.



  1. Install water pump assembly.
  2. Install water pump bolts. Initially finger tighten bolts
  • Torque: 25 Nm (18 ft. lbs.)



  1. Install the water feed tube.
  2. Lubricate the feed tube O-ring with silicone gel lubricant.
  3. Install water feed tube by twisting and pushing toward water pump. Take care not to tear or damage the O-ring.
  4. Install thermostat housing to block bolts.
  • Torque: 10 Nm (89 inch lbs.)



  1. Install exhaust manifold heat shield.


  1. Install air cleaner assembly and air inlet tube. Refer to "Air Cleaner Assembly Installation".
  2. Connect negative battery cable.
  3. Add coolant.

Aug 27, 2010 | Saturn LS Cars & Trucks

2 Answers

Replacing waterpump in1999 nissan pathfinder


Water Pump Removal & Installation To Remove:
  1. Allow the engine to cool and drain the coolant from the radiator and both engine block plugs.
  2. Remove the fan shroud and both radiator hoses.
  3. Remove the drive belts.
  4. Remove the water pump pulley.
  5. Remove the crankshaft pulley.
  6. Remove the timing belt covers.
  7. Remove the water pump.
Water pump removal/installation 7924vg20.gif

To Install:
  1. Install the water pump with new gasket.
  2. Install the timing belt covers.
  3. Install the crankshaft pulley.
  4. Install the water pump pulley.
  5. Install the drive belts and fan shroud.
  6. Install the radiator hoses.
  7. Install the coolant drain plugs.
  8. Refill the cooling system.
prev.gif next.gif

Aug 10, 2010 | 1997 Nissan Pathfinder

1 Answer

Where can i find a diagram of the 1996 mercury villager water pump placement


I can sell you a shop manual ans wiring book for $25 plus postage or you can go to our website.

http://groups.yahoo.com/group/villagerquest/

  1. Drain the cooling system. Refer to Section 03-03 for the procedure.
  1. Disconnect the battery ground cable (14301).
  1. Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the removal procedures.
  1. Raise and support the vehicle.
  1. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts.




  1. Remove the water pump pulley from the water pump (8501).
  1. Remove the crankshaft pulley (6312). Refer to the procedure in this section.
  1. Remove the five lower engine front cover bolts and the lower engine front cover (6019).




  1. NOTE: Make a note of the location of the one water pump stud/bolt for ease of installation.

    Remove the six water pump bolts.




  1. Remove the water pump.
Installation
  1. NOTE: Ensure the mating surfaces between the water pump and the cylinder block (6010) are cleaned of any sealant material.

    Install a continuous 2.0-3.0mm (0.079-0.118 inch) wide bead of Gasket Maker E2AZ-19562-B or equivalent meeting Ford specification WSK-M2G348-A5, on the water pump and position the water pump on the cylinder block.




  1. NOTE: Refer to the note made during removal for the location of the stud/bolt.

    Install the six water pump bolts. Tighten the water pump bolts to 16-21 Nm (12-15 lb-ft).
  1. Position the water pump pulley on the water pump and install the four water pump pulley bolts.
  1. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley, and tighten the four water pump pulley bolts to 16-21 Nm (12-15 lb-ft).
  1. Install the lower engine front cover and the five lower engine front cover bolts. Tighten the five lower engine front cover bolts to 3-5 Nm (27-44 lb-in).
  1. Install the crankshaft pulley. Refer to the procedure in this section.
  1. Lower the vehicle.
  1. Install and adjust the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the installation and adjustment procedures.
  1. Connect the battery ground cable.
  1. Fill the cooling system. Refer to Section 03-03 for the procedure.
  1. Start the engine (6007) and check for leaks.

Apr 26, 2010 | 1996 Mercury Villager

1 Answer

How do I change a water pump on a 2004 kia sorento?


Kia Sorento 2003-05
Water Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Drain the cooling system.
  3. Disconnect the negative battery cable.
  4. Remove the drive belt and the water pump pulley.
  5. Remove the timing belt cover, timing belt, auto tensioner and idler pulley.
  6. Remove the water outlet fitting, the thermostat case and the water pump fitting.
  7. Remove the water pump mounting bolts.
  8. Remove the water pump.

  9. dc45c19.jpg

    Fig. Water pump and timing belt assembly-exploded view

To install:

1016213.jpg

Fig. Water pump bolt locations
  1. Clean the gasket surfaces of the water pump body and the cylinder block.
  2. Install the new water pump gasket and pump assembly. Tighten the bolts to 12-16 ft. lbs. (17-22 Nm).
  3. Install the water pump fitting, the thermostat case and the water outlet fitting.
  4. Install the auto tensioner and timing belt. Adjust the timing belt tension, then install the timing belt cover.
  5. Install the drive belt, water pump pulley and then adjust the auto tensioner.
  6. Refill the coolant.
  7. Run the engine and check for leaks.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Disconnect the negative battery cable.
  4. Remove the drive belt and the water pump pulley.
  5. Remove the timing belt cover, timing belt, auto tensioner and idler pulley.
  6. Remove the water outlet fitting, the thermostat case and the water pump fitting.
  7. Remove the water pump mounting bolts.
  8. Remove the water pump.

To install:


e9be8c3.jpg

Fig. Water pump bolt locations

596080e.jpg

Fig. Water pump O-ring installation
  1. Clean the gasket surfaces of the water pump body and the cylinder block.
  2. Install the new water pump gasket and pump assembly. Tighten the bolts to 12-16 ft. lbs. (17-22 Nm).
  3. Install the water pump fitting, the thermostat case and the water outlet fitting.
  4. Install the auto tensioner and timing belt. Adjust the timing belt tension, then install the timing belt cover.
  5. Install the drive belt, water pump pulley and then adjust the auto tensioner.
  6. To adjust the drive belt tension, hang the belt on the pulley of the tensioner and install the tensioner.
    NOTE If the tensioner is already installed, loosen its mounting bolts to allow belt installation
  7. Install the drive belt.
  8. Adjust the belt tension to specification by turning the adjusting bolt clockwise or counterclockwise.
  9. Air conditioning belt tension should be 0.28-0.039 inch. Alternator belt tension should be 0.39-0.051 inch. Power steering belt tension should be 0.31-0.051 inch.
  10. Torque the tensioner assembly bolt to 33-36 ft. lbs. (45-50 Nm).
  11. Refill the coolant.
  12. Run the engine and check for leaks.

TY for using Fixya; remember comment and rated this.

Apr 01, 2010 | 2004 Kia Sorento

1 Answer

How do i change the water pump on a 1999 2.5 v6 chrysler sebring?


Hello,

Removal:
Drain cooling system, remove the timing belt if necessary. Remove water pump mounting bolts. Separate water pump from water inlet pipe and remove.

Inspection:
Replace water pump if it has damage or cracks to pump body. Check the shaft seal for any leaks as evidence by traces of coolant from vent hole. Check for any impeller rubbing inside pump, and for loose or rough bearings.

Installation:
Clean all gasket and "O" ring surfaces. Install NEW "O" ring on water pipe (wet "O" ring with water to aid assembly). DO NOT allow oil or grease to contact "O" ring. Install NEW gasket on water pump, and install pump inlet opening over water pipe. Install pump-to-block bolts and tighten to specification 18 FT. Lbs. (25n.m). To complete installation, reverse removal procedure.

Hope this helps :)

Oct 19, 2009 | 1998 Chrysler Sebring

2 Answers

REMOVAL OF WATER PUMP ON 95 MERCURY VILLAGER


go here too http://autos.groups.yahoo.com/group/villagerquest/ Section 03-01: Engine 1996 Villager Workshop Manual IN-VEHICLE SERVICE -------------------------------------------------------------------------------- Water Pump Removal Water Pump Removal Drain the cooling system. Refer to Section 03-03 for the procedure. Disconnect the battery ground cable (14301). Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the removal procedures. Raise and support the vehicle. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts. Remove the water pump pulley from the water pump (8501). Remove the crankshaft pulley (6312). Refer to the procedure in this section. Remove the five lower engine front cover bolts and the lower engine front cover (6019). NOTE: Make a note of the location of the one water pump stud/bolt for ease of installation. Remove the six water pump bolts. Remove the water pump. Installation NOTE: Ensure the mating surfaces between the water pump and the cylinder block (6010) are cleaned of any sealant material. Install a continuous 2.0-3.0mm (0.079-0.118 inch) wide bead of Gasket Maker E2AZ-19562-B or equivalent meeting Ford specification WSK-M2G348-A5, on the water pump and position the water pump on the cylinder block. NOTE: Refer to the note made during removal for the location of the stud/bolt. Install the six water pump bolts. Tighten the water pump bolts to 16-21 Nm (12-15 lb-ft). Position the water pump pulley on the water pump and install the four water pump pulley bolts. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley, and tighten the four water pump pulley bolts to 16-21 Nm (12-15 lb-ft). Install the lower engine front cover and the five lower engine front cover bolts. Tighten the five lower engine front cover bolts to 3-5 Nm (27-44 lb-in). Install the crankshaft pulley. Refer to the procedure in this section. Lower the vehicle. Install and adjust the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the installation and adjustment procedures. Connect the battery ground cable. Fill the cooling system. Refer to Section 03-03 for the procedure. Start the engine (6007) and check for leaks.

Jun 06, 2009 | 1995 Mercury Villager

1 Answer

Removal of water pump


Removing alternator drive belt, refer to Engine.
Release the belt pulley from the water pump.

98758195

Drain coolant.
Release water pump.

98758196

Insert two M6 screws in water-pump thread and press out water pump evenly from gear case.

98758197

Installation:
Replace sealing ring.

May 25, 2009 | 1996 BMW 318

Not finding what you are looking for?
2000 Toyota Tundra Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...