Question about 2003 Chevrolet Trailblazer Ext

1 Answer

Drivers side door got wet inside and now none of the power equipment work on the drives side door

Posted by on

1 Answer

The same thing happened to me before in my 2003 Trailblazer LS. The service dept noticed the water had caused corrosion and shorting on the controls inside the door rest with the window controls. You may be able to repair it yourself and then place grease oil vasoline over the connectors afterwards.... to prevent the same thing from happening again.

Posted on Aug 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Door is loked on rear driver side want open


Won't open from outside? Won't open from inside? Equipped with power door locks? IF so, and won't open inside/outside, suspect stuck power door lock actuator. Sometimes working the lock/unlock button will make the door unlock. If not, the door will require disassembly from inside to determine what the failure may be. If the door needs disassembly while in the closed position, the paneling/clips may get damaged FYI

Dec 22, 2015 | 2001 Chevrolet Lumina

1 Answer

2006 Lexus LS430 with easy locks. Driver side rear door comes open while driving


Check out spring housing inside the door lock actuator. I had the same problem, some work anf JB weld will fix it,

Jul 23, 2012 | 2006 Lexus Ls 430

1 Answer

2000 Buick LeSabre-- None of the controls on the drivers side door work. This includes the power locks, power windows and trunk release. All of the other power windows and power door controls work-- just...


Follow the wiring from between the door and the body to the insides under the dashboard. It's usually inside a soft plastic or rubber tube for protection. Follow the wire bundle if you can to the fuse panel. I don't know exactly where it is on this car, but it's usually very close to the left and underneath of the dashboard. You may find that a plug that has all these wires together has come loose somewhere.

Please update here on your progress. Good luck!

Aug 02, 2010 | 2001 Buick LeSabre

1 Answer

97 chev blazer door panel removal on the passenger side


Remove the inside door handle bezel. Remove the window regulator handle, if equipped. Remove the power accessory switch mounting panel, if equipped with power accessories.
  • Remove the trim panel armrest screws.
  • Use the J 38778 in order to release the door trim panel retainers.
  • Remove the door trim panel from the door.
  • Remove the door trim panel. .

  • Read more: http://www.justanswer.com/questions/2mjs0-i-need-to-replace-the-driver-side-power-mirror-on-a-1997-chevy#ixzz0ecmMaGqz

    Feb 05, 2010 | 1997 Chevrolet Blazer

    1 Answer

    Tying to locate the fuse (fuses) for power windows, power lock (drivers side only) and power mirrors. All switches on my drivers dide door not working. Checked fuse cover under dash and hood, none list any...


    Hi
    sounds to me like the electrical cable inside the drivers door has come unplugged or broken where door swings( youll see a black ribbed rubber piece that shields the cable check for damage) youll need to remove the door panel for visual. The fuse should be listed on the fuse cover (interior). If the passenger side is functional it is more likely that the cable is unplugged or damaged as the passenger and drivers side would be on same circuit.
    I hope this helps you

    Dec 30, 2009 | 2004 Jeep Grand Cherokee

    1 Answer

    How to remove the inside door panel from a dodge 2005 2500 pick up


    FRONT DOOR TRIM PANEL - REMOVAL
    Release door latch and open door.
    Roll window down.
    Remove window crank Window Crank - Typical , if equipped.
    Remove screws attaching trim panel to door Door Trim Panel and Trim Panel Screw
    CAUTION: Do not forcibly pull trim panel from door, damage to trim panel may occur.

    Simultaneously lift upward and outward to release retainer steps from inner door panel Trim Panel Retainer
    Disengage inside handle linkage rod from inside handle.
    Disconnect speaker harness wire connector Speaker And Power Mirror Connector
    Disengage power mirror wire connector, if equipped (driver's side only) Speaker And Power Mirror Connector
    Disengage clips attaching power window/lock switch panel to door trim panel. Disengage wire connector from switch panel, if equipped Power Door Lock/Window Connector
    Separate door trim panel from vehicle.
    INSTALLATION
    Position trim panel at door.
    Engage wire connector for window/lock switch panel, if equipped. Engage clips attaching power window/lock switch panel to door trim panel.
    Engage power mirror wire connector, if equipped.
    Connect speaker harness wire connector.
    Engage inside handle linkage rod to inside handle.
    Align trim panel retainer steps with inner door panel and slide trim panel into place.
    Install screws attaching trim panel to door.
    Install window crank, if equipped.

    Hope helped with this; remember rated this help. Good luck.

    Nov 12, 2009 | 2005 Dodge Ram 2500 Truck

    1 Answer

    Fallen driver's side window


    probably need a new window regulator. ebay. 93 to 98 should fit.

    Section 01-05: Trim, Interior 1998 Villager Workshop Manual
    REMOVAL AND INSTALLATION Trim Panel(s), Door Front
    Removal
    1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
    1. swv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
      Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .




    1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
    1. Pull the shop rag back and forth to release the window regulator handle clip.




    1. Remove the three cover caps and front door trim panel screws.
    1. Remove the one front door trim panel capped screws from the door pull handle.
    1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
    1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
    1. Remove the front door trim panel.
    Installation
    To install, reverse the removal procedure.
    ---------------------------------------------------------
    Window Regulator, Power Front Door
    Removal
    1. Disconnect the battery ground cable (14301) .
    1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
    1. Remove the two front door brace bolts and the front door brace.


      415712f.gif

    1. Disconnect the front window regulator electric drive electrical connector.
    1. Remove the four front door window glass regulator track bolts.

      67b6136.gif


    1. Remove the three front window regulator electric drive bolts.
    1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
    Installation
    1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
    1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
    1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.

    Apr 29, 2009 | 1998 Mercury Villager

    1 Answer

    All 4 electric windows will not go up or down.


    First, check the drivers door to body wiring where it passes between the doors. I'd take the panel off and start from the inside and work your way through the part that travels inside the rubber cover to the car. These are notorious for rotting wires in that area, which will cause a large problem.

    If the harness is ok, replace the drivers door power window switch assembly. If the drivers door switches are bad then none of the others will work either. I see this very frequently as well from people who use too much Armour All cleaner, or drive with their window down in the rain and get it wet(smokers usually).

    Nov 28, 2008 | Hyundai Motor 2003 Elantra

    1 Answer

    Driver's side door power locks are stuck; door stuck shut.


    sounds like the rods are disconnected the clips hold the rods in place the latching mechanism holds the handle in place as well did you replace the speakers or did a shop? if a shop did then they caused this if you did then you may have caused this either way untill you reattach the rods none of it will work. you will have to manually open the door at the latch from inside teh door behind the panel.

    Jul 16, 2008 | 1993 Ford Mustang

    Not finding what you are looking for?
    Cars & Trucks Logo

    129 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    61249 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...