Question about Chevrolet 1500

Open Question

Brake lights on 91 chevy silverado don't work. everything else okay. replaced the bulbs and plug assembly.

Posted by on

6 Suggested Answers

  • 68 Answers

SOURCE: Brake Lights Stay on 91 Chevy Silverado

there is a short in the wire underneath by the brake pedal keeping it on

Posted on Nov 20, 2008

keemo68
  • 1263 Answers

SOURCE: where doe's that spring go on rear brake drums 1996 chevy truck every thing is at top not at bottom, star wheel adjuster?

there should be several springs. first there are (2) real short springs that hold the shoes to the dust cover/back plate. they go in the center of each shoe. then there is a short spring that goes at the bottom where the adjuster is located. there should be a hole in each shoe. finally there is a long spring that goes at the top where your brake cylinder is and this is what gets attched last after your emergancy brake levers are placed between the shoes .

Posted on Apr 17, 2009

  • 306 Answers

SOURCE: 2007 Chevy Silverado Center brake light works but back ones dont

There is a probable bad wiring connection in problem one and three.
#2 Possible water leak causing bulb break. Try wd40 in socket. you need a wiring diagam and cheap voltmeter if you want do it yourself.

Posted on May 09, 2009

  • 4 Answers

SOURCE: nissan almera brake lights not working,checked

Check the brake light switch under the dash at the brake peddle and make sure its working if it does not close when you depress the brake peddle the lights will not work You may hve to remove the lower cover for the dash to get at the switch

Posted on Sep 03, 2009

  • 750 Answers

SOURCE: 1999 Chevy Silverado - 3rd Brake Light Inop

if you can trace the wires and look for a loose jack or broken wire

Posted on Sep 16, 2009

Testimonial: "Thank you. I'm sure it's narrowed down to a wiring issue, but I am not sure how it is wired."

  • 99 Answers

SOURCE: i need a diagram of rear drum brake assembly of a

Haynes manual should have a breakdown. They run about $20 at the parts store.

Posted on Oct 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On my 1997 Chevy truck my brake lights don't work


check your grond wire a lot of times they will corrode and lose connection after you check fuses bulbs etc.

Apr 18, 2012 | 1999 Chevrolet Silverado 1500

1 Answer

How do I replace brake lights on 2006 Chevy Silverado?


The bulb, or the full assembly?

If just the bulb, it's easy. Lower the tailgate. On the inside you will see the 2 hex screws that hold the assembly in place. Remove those carefully so you don't lose the nut inside the body, and carefully pull the assembly out. The main brake light is at the top, just twist the socket and pull gently. The bulb just pulls out of the socket.

DO NOT TOUCH THE NEW BULB GLASS! It will cause it to burn out much faster.

Replace the bulb in the housing, and then test it. Once it works, reverse the steps. Also, do not do this if it is very humid or rainy outside. The moisture can get into the assembly, and cause an early failure due to condensation. If you see water inside, take it apart and let it sit in the open to dry out. Then put it back in.

Aug 14, 2011 | 2006 Chevrolet Silverado 1500 2WD

1 Answer

I have a 2004 chevy silverado. my brake lights stopped working so i replaced them and still nothing. the only one that works is the brake light on top of the cab. any suggestions?


If all bulbs are good is most likely printed circuit board that bulbs plug into, very common to go bad. HELP/motormite sells them in 2 pack for both sides. Available in any auto parts store for less than the dealer charges.

Jun 09, 2010 | 2004 Chevrolet Silverado

1 Answer

Replacing brake switch on a 2000 Chevy Siverado, wil lthios take care of the problem...brake lights work okay..but when you brake and signal at the same time it stays lit solid and when our back up...


Check the brightness of the bulbs when they work. It sounds like a filiment broke in one of them and is laying across the other filiment in the bulb causing all lights to come on at times or not at all. You probably have one or more bad bulbs.

Nov 18, 2009 | 2000 Chevrolet Silverado

1 Answer

Brake lights on a 2003 chevy silverado 2500HD wont work.


same bulb but 2 seperate elements. wiring diagram u should be able to obtain from your local auto parts store like autozone(preferred)

Sep 23, 2009 | 2003 Chevrolet Silverado 2500HD

2 Answers

1999 Chevy Silverado - 3rd Brake Light Inop


if you can trace the wires and look for a loose jack or broken wire

Sep 16, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

Left brake light not working fuse bulb ok


check all your wiring from the light to the fuse panal. that should fix it

Apr 18, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

Brake lights do not work, all other lights work.


It is a common chevy problem for the circuit board that holds to bulb to fail, are your running lights and signals still working back there as well? If not then you need to replace the boards.

Dec 12, 2008 | 2007 Chevrolet Silverado Classic SS New...

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...