Question about 1993 Ford Taurus

1 Answer

Front motor mount

Whats the trick for removing the broken motor mount unable to remove top bolt, any tricks to it?

Posted by on

  • Anonymous Jul 26, 2008

    1990 ford taurus gl 3.0

  • Anonymous Mar 31, 2014

    How to remove front motor mount

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Place a block under motor, jack the motor up until you have clearance to remove top bolt.

Posted on Aug 08, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to replace oil pan gasket on a 1985 dodge pickup truck with a 318 automatic


trick is loosen the motor mounts and lift the motor slightly so pan can clear the frame . no big deal

Sep 11, 2016 | Dodge Cars & Trucks

1 Answer

1985 Pontiac 6000 4cyl 2.5L Base. - Ignition Module


Yes. Raise and support the vehicle (not by the sub-frame). Place a jack under the rear of the sub-frame and remove the rear sub-frame mounting bolts. Loosen the front bolts a few turns, but do not remove. Then slowly lower the sub-frame until it is being supported by only the front bolts. This will provide the clearance you need to get your hands in at the ignition module.

Apr 23, 2012 | Cars & Trucks

1 Answer

Getting the oil pan off,and the tricks to do it?


Remove fan and fan shroud.remove engine mount bolts,raise engine at front pulley with block of wood between jack and pulley. make sure distributor cap won't hit firewall, you may have to remove cap.

Jul 16, 2011 | 1987 Ford Ranger

1 Answer

I have a 1998 Dodge Avenger with a 2.0 (4cyl). Does anyone know of any tricks to remove the passenger side motor mount to engine bolts without removing the engine from the car ????


Put the car on stands and put a jack within a few inches of the under side of the engine. Loosen the bolt mounts by about have a turn. Have a friend use a length of timber and use jack top as a lever fulcrum to take the weight of the engine off the mount whilst you remove the mounting bolts. Take care not to put any load on the oil pan as it can crush quite easily. You should be able to adjust the engine attitude about two inches without having to detach anything, this is enough room to get the old mount out and therefore the new one in. Take your time and keep safe

Nov 30, 2010 | 1998 Dodge Avenger

1 Answer

How do you lower the motor to change the back spark plugs


You dont need to lower the motor to do this you may have to get from the underneigth of the car or remove the rear wiper bucket this will give you more room, a trick i learned but not sure if this van has it is if you have two wish bone type engine mounts on top of the engine then unbolt them and pry engine forward then slide bolt into mount and hole on bottom of mount, here a diadram of the mount. hope this helps.9c8a95b.jpg

Sep 10, 2010 | 2004 Buick Rendezvous

1 Answer

How to remove power steering and alternator belts on an Xb 2006


maybe the bolts are reverse thread?? if not heating the bolts till the locktite melts is another way

Jul 19, 2010 | 2006 Scion xB

1 Answer

Its immpossible to get to the top bolt for the starter on a 99 ford explorer, any tricks?


support the engine and remove motor mounts on the side the motor will lean the opp. way

Feb 12, 2010 | 1999 Ford Explorer

1 Answer

Rusted out oil pan


Loosening motor mounts and jacking up engine may give you some room, but might not be enough. Supporting the frame and lowering the front axle assembly is another option, but you will need a helping hand. Replacement is tricky in keeping the gasket in place. Make studs out of bolts that are the same size as factory by cutting the heads off. They will help hold the gasket in place as well as guide the pan into proper position. Cut screwdriver slots in them for easier removal after you get the mounting bolts started.

Sep 21, 2009 | 1998 Ford Ranger SuperCab

2 Answers

How do you change the starter on a 1997 vw jetta?


usally there are 3 bolts holding the starter motor in and its situated somewere on the flywheel iether the back of the engine or the front.take of the wires that are screwed to the solinoid of the starter motor then it should come off.

Mar 06, 2009 | 1997 Volkswagen Jetta

Not finding what you are looking for?
1993 Ford Taurus Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...