Question about Jeep Cherokee

1 Answer

Problems with bleeding a 1994 jeep cherokee master and slave cyclinder

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,071 Answers

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1994 Jeep Grand Cherokee brake pedal goes all the way to the floor. Recently replaced calipers and master cylinder and bled the whole system. Brake pedal goes all the way to the floor when first pushed...


Not bleed properly
or you have a rusted out line (leak)

There is NO Procedure-- that when driving a
vehicle or bleeding brakes,do you ever pump them

Dec 03, 2014 | 1994 Jeep Grand Cherokee

1 Answer

My 1987 jeep wrangler wont shift into gear...i have replaced the clutch master cyclinder or it may be called the slave cylinder whichever is located near the transmission...what do i do next?


If you have replaced the slave unit, and bled the system, then I'd replace the master cylinder on the firewall and bleed it again.
It seems though that you are a bit week on the diagnostics end...A slave unit is bad only if it is leaking fluid or frozen from non use. A bad master, can either leak externally (usually visible where the rod goes into it on the passenger side of the firewall) or internally bypass causing the slave not to move. The line between them cannot be leaking either or nothing will work. If everything appears to be working but the clutch will not disengage it is possible that the clutch itself is bad.

Sep 17, 2010 | 1987 Jeep Wrangler

1 Answer

Clutch pedal is going to the floor. about 2 mos ago replaced the master cylinder bled the system worked good now its doing the same thing. if i bleed the system it works good again for a day or so. dont...


i dont think its bearing problem.Did you fit a [new] master cyclinder,if you did then its the [slave ]cyclinder .,its a pressure problem not a bearing problem.adrian,,,,

Aug 04, 2010 | 1992 Jeep Wrangler

2 Answers

Have a 1990 150 lariat 4x4 put new trans in,clutch,slave cyclinder,and clutch master cyclinder, still having problems with the clutch pedal being low, i bleeded the clutch several time but it won't come...


I assume that the master cylinder is correctly installed. In that case the master cylinder's piston rod (to which the pedal is attached) is too short or maladjusted.

Apr 24, 2010 | 1990 Ford F150

1 Answer

My 94 jeep wrangler 4.0 when stopped with car in gear with clutch pedal pressed to floor sometimes the clutch disengages and i have changed slave cylinder and clutch resevoir is full. my version has...


may have a bad mastercylinder for slave, also did you bleed system good and no leaks,id say master may be the problem or clutch preasure plate is bad .good luck.

Oct 27, 2009 | 1996 Jeep Cherokee

1 Answer

STILL DOESN"T WORK!!!


you need to use a pressure system to add fluid into the master cylinder and then bleed it.

Mar 26, 2009 | 1994 Jeep Grand Cherokee

1 Answer

Nov. 94 Grand Cherokee Jeep no back brakes


I bet you still have air back there. If you didn't bleed the system after the master you need to do that. Bench bleeding a master doesn't always work.Also badly out of adjustment rear brakes can act the same way.

Nov 26, 2008 | 1994 Jeep Grand Cherokee

1 Answer

1994 Jeep Wrangler 4cyl - Bleeding slave cylinder


This is not a bleeder hole, this is a weep hole like in a water pump to see when there is seepage past the seals.

Bench bleed the system. With the master cyl. line and slave cyl assembled, place the master cylinder in a vise, fill the master cyllinder. actuate the slave cylinder back and forth lower than the master cyl. This will allow the air to escape upwards back into and out of the master cyl.
Once bled the system can be installed.

Good Luck

Aug 06, 2008 | 1994 Jeep Wrangler

5 Answers

94 jeep grand cherokee laredo brake problem


Hi there!

Check for leaks at the slave cylinders and flexi hoses.

After several attempts of losing pressure - check the brake fluid level in the master.

If you arn't losing any fluid, You've got a damaged seal in the Master cylinder, or are drawing air in due to improper adjustment (excess travel) of slave cylinders.

Are you trying this with engine running? - How does this affect it (using servo assist)

Jun 15, 2008 | 1994 Jeep Grand Cherokee

2 Answers

1999 Dodge Ram 3500 Pickup - Clutch


use a hand vacumn and cover over the reservoir, apply light vacumn and the air will come to the reservoir, usually take 2 or 3 time and the air will work back out to the top,

Jun 05, 2008 | 2001 Dodge Ram 3500 Truck

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...